Topics A–Z
Race engineering topics A–Z
All 113 lessons in alphabetical order, each with its short answer. Open a lesson for the full explanation at four levels, the formulas and a quiz.
A
- ABS in GT3 & Cup cars: maps, interaction with balance, and what it hidesBrakesL2
- Motorsport ABS keeps each wheel near its optimum slip, but it doesn't make brake balance irrelevant. Learn to read ABS activity, choose maps, and spot when ABS is masking a setup problem.
- Ackermann geometry: 100 %, parallel and anti-AckermannSteeringL1
- Ackermann sets how much more the inside front wheel steers than the outside. It is exact for slow parking-speed turns, nearly irrelevant in fast corners, and at the limit it is really a tool for distributing slip angle between a loaded and an unloaded tyre.
- Aero balance & centre of pressureAeroL1
- Aero balance is the front share of total downforce (equivalently, where the centre of pressure sits along the wheelbase). Its relation to the static weight distribution decides how the car's balance changes from slow to fast corners.
- Aero efficiency & trim choice: low drag vs high downforceAeroL2
- L/D describes efficiency, but the right trim is decided by the track's exchange rate between downforce and drag. Monza and Le Mans reward low drag; Monaco and Hungary reward downforce. Marginal efficiency of each change matters more than the car's overall L/D.
- Aero in traffic (dirty air, slipstream) & yaw sensitivityAeroL2
- Following another car reduces dynamic pressure and disturbs the flow: less drag on the straight but lost (mostly front) downforce in fast corners. Yaw from body slip and crosswind changes downforce and balance too. Both should shape race setup and strategy.
- Analysing braking technique: brake point, peak pressure, build rate, trail braking and releaseDriverL1
- Braking is where drivers differ most. Quantify brake point, time to peak, peak pressure, modulation and release with a handful of math channels, and connect them to deceleration and corner entry.
- Analysis software essentials: plots, overlays, XY, histograms, filtering, run notesDataL1
- Most analysis is comparison. Know when to plot against time or distance, how to read XY plots and histograms, how filtering changes what you see, and how to keep run notes so data stays tied to a setup.
- Anti-dive, anti-squat & anti-liftGeometryL2
- Side-view geometry can route part of the longitudinal load transfer through the links instead of the springs, controlling pitch. It never changes how much load is transferred – only the path, and therefore pitch, platform and feel.
- Anti-roll bars and roll stiffness distributionSprings & ARBL1
- Anti-roll bars add roll stiffness without adding heave stiffness. The front/rear split of total roll stiffness sets most of the lateral load transfer distribution (LLTD) and is the primary mechanical balance tool.
B
- Balance of Performance: restrictors, boost, power & energy limits, weightEngineL2
- BoP equalises different cars with restrictors, boost tables, power caps, energy per stint and minimum weight. Each lever changes a different part of the performance envelope — and therefore which setup and strategy decisions are optimal.
- Banking, grade and vertical curvature effectsWeight transferL2
- Banking, uphill/downhill grade and crests/compressions change both the normal load on the tyres and what the accelerometers read. Correct for them before comparing grip, balance or load-transfer data between corners or tracks.
- BoP, regulation awareness and sporting regulationsStrategyL2
- Regulations define the optimisation space. Know how Balance of Performance works, which parameters it fixes, and the sporting rules that shape strategy: drive times, refuelling procedures, mandatory stops, tyre allocations and parc fermé.
- Brake bias in practice: balance bar, master cylinders, in-car adjust & migrationBrakesL2
- How the hydraulic bias is actually set — balance bar position, master-cylinder sizes, driver adjusters — how to measure it with pressure sensors, and how brake-by-wire migration in hybrid prototypes changes the bias through the braking event.
- Brake temperatures & cooling: windows, carbon vs iron, ducts, glazingBrakesL2
- Brakes convert ~1 MJ per front disc in a big stop into heat. Disc and pad compounds work in temperature windows; ducting, compound choice and bias keep them there. Brake heat also feeds tyre temperatures and pressures.
- Braking analysis with data: quickness, effort, brake points, release & pedal travelBrakesL2
- The standard data toolkit for braking (Segers ch. 5): how fast the driver builds deceleration, how much of the available grip is used, where the brake point is and why it moves, how the release blends into cornering, and what pedal travel and pressure reveal about the hardware.
- Braking physics, longitudinal load transfer & ideal brake balanceBrakesL1
- Braking moves load from the rear to the front axle in proportion to deceleration × CG height / wheelbase. The ideal brake force split follows the axle loads, so it changes with deceleration, grip level and downforce — and it is not the same as the pressure bias shown on the dash.
- Bump steer & roll steerGeometryL1
- Toe that changes with wheel travel steers the car without the driver. Measuring it with a bump-steer gauge and shimming the track-rod end is a core workshop skill; using roll steer deliberately is a balance tool.
- Bump stops, packers and progressive ratesSprings & ARBL2
- Bump stops (bump rubbers) and packers turn a linear suspension into a progressive one. Used deliberately they control ride height at speed – the aero platform – while keeping softer springs for low-speed grip; used carelessly they cause sudden balance shifts.
C
- Camber and camber thrustTyresL1
- Negative static camber is run so the loaded outside tyre has an even contact pressure at the limit, not mainly for camber thrust. The cost is braking/traction patch, inner-shoulder heat and tyre-supplier limits.
- Camber gain & camber compensation in rollGeometryL1
- Body roll tilts the outside tyre towards positive camber; suspension geometry gains negative camber in bump to fight it. How much is recovered – and what it costs in heave – shapes static camber choice and tyre temperatures.
- Caster, kingpin inclination, scrub radius & mechanical trailGeometryL1
- The steering axis geometry decides steering weight, self-centring, camber change with steer and the diagonal weight jacking that happens every time the driver turns the wheel.
- Checking vital signs and building alarm channelsDataL1
- The first job of the data system is to keep the car running. Check vitals before performance, learn their normal patterns, and build alarm logic that warns the driver without crying wolf.
- Choosing ratios: top gear, gaps & corner gearsGearboxL2
- Pick top gear for the longest straight in race conditions (tow!), space the intermediates for the speed bands the track actually uses, and choose corner gears so the exit sits in the rpm of best acceleration without a forced mid-exit shift.
- Combined slip and the friction ellipseTyresL1
- A tyre has one friction budget shared between lateral and longitudinal force. The friction ellipse describes the trade, and its non-linearity explains trail braking, exit traction limits and many balance complaints.
- Comparing laps: delta time, segment times and track mappingDataL1
- Find where time is gained or lost before asking why. Delta-time channels, segment times, theoretical best laps and accurate distance alignment are the backbone of every debrief.
- Comparing two drivers and coaching with dataDriverL2
- Comparison is the heart of driver development. Use a structured process – speed and delta first, then inputs, then line – and deliver it in a way the driver can absorb, acknowledging that car balance and driver technique are intertwined.
- Compliance steer & compliance camberGeometryL2
- Real suspensions deflect under load. Compliance steer and camber under cornering forces can be as large as the kinematic effects engineers carefully set on the alignment pad.
- Consistency analysis and lap-time variationDriverL2
- Race pace is won by consistency. Quantify it with lap-time statistics, sector reports and per-corner metrics, separate it from fuel and tyre effects, and recognise the data signatures of fatigue.
- Corner phases and which tools act in eachSetupL1
- A corner is a sequence – braking, entry, mid/apex, exit – and each phase has a different load state and therefore a different set of effective setup tools. Matching the tool to the phase is the core skill of setup work.
- Corner weights, cross weight and setting up on scalesSprings & ARBL1
- Corner weights describe how the static load is shared between the four tyres. The diagonal (cross weight) is adjusted with spring platforms and determines whether the car behaves the same in left- and right-hand corners.
D
- Damper fundamentals: force vs velocity, bump vs reboundDampersL1
- A damper produces force from shaft velocity, not displacement. Its force–velocity curve (shape, bump/rebound asymmetry, knee) is what you tune; it only acts while the suspension is moving.
- Damper velocity histograms, box plots and run chartsDampersL2
- The shock-speed histogram characterises each damper as installed on the car. Symmetry, zero-bin height, % time in low/high-speed bump and rebound, and statistics like standard deviation, skewness and kurtosis turn it into objective metrics you can track lap by lap.
- Dampers and transient balance: entry and exitDampersL2
- While the body is rolling and pitching, damper forces add to the spring forces and change how load transfer is distributed front to rear. Low-speed bump and rebound, front vs rear, are therefore the tools for entry and exit balance – not for mid-corner.
- Damping ratio and critical damping (body and wheel)DampersL1
- Damping ratio ζ normalises the damper coefficient against mass and stiffness. Race cars typically run a body damping index ζ ≈ 0.6–0.8 at low shaft speed and wheel ζ ≈ 0.3–0.5 at high shaft speed – single-corner indices for comparing setups, not the true modal damping of the car.
- Data analysis with metrics, KPIs and run chartsDataL2
- Compress thousands of samples into one number per lap. Well-designed metrics in run charts reveal trends across stints, days and seasons – and let you relate any parameter to lap time quickly.
- Diff effect on yaw: entry stability, mid-corner understeer, exit tractionDifferentialL2
- A left/right drive or braking force difference produces a yaw moment ΔF·t/2. Its sign depends on which wheel is faster, so the same diff stabilises entry, resists mid-corner rotation and can either push or snap on exit.
- Differentials in specific cars: GT3, formula cars & on-wheel diff mapsDifferentialL2
- What you can change depends on the category: GT3s usually offer preload (sometimes homologated ramp/plate options), spec formula cars offer little, and the F1-style hydraulic diff with entry/mid/exit maps on the wheel shows what an unrestricted diff can do.
- Downforce, drag & air densityAeroL1
- Downforce and drag both scale with dynamic pressure ½ρV². Engineers work with the products C_L·A and C_D·A, and must correct for air density (temperature, pressure, altitude, humidity) before comparing sessions.
- Driver activities that indicate vehicle balanceDriverL2
- Drivers react to a handling problem before they can describe it. Steering, throttle and lateral g patterns reveal understeer and oversteer by corner phase – and distinguish a car problem from a driver-induced one.
E
- Engine braking, downshifts & rear stability on entry (diff, hybrid regen, brake-by-wire)BrakesL2
- The rear axle's braking on entry is not only the rear brakes: engine braking, downshift transients, the differential and (on hybrids) regeneration all add rear torque. Managing their sum is the key to a stable but rotating car on entry.
- Engine vital signs & data monitoringEngineL1
- Before looking at performance, confirm the car is healthy: oil and fuel pressure, fluid temperatures, lambda, voltage, rpm. Good alarm channels and trend views catch failures a run before they happen.
- Engineer–driver communication: radio and debrief structureStrategyL1
- The radio is for short, timely, prioritised information; the debrief is for structured, unbiased capture of the driver’s experience followed by data. Both depend on agreed vocabulary and trust.
F
- Frequency analysis basics: FFT, PSD and the sampling theoremDataL2
- Suspension behaviour is easier to judge in the frequency domain: an FFT or PSD of damper, ride-height and acceleration signals reveals body and wheel modes, and transfer functions quantify platform control and tyre-load fluctuation.
- Frequency-domain suspension analysis & modal decompositionDampersL3
- Transfer functions, power spectral densities and modal decomposition (heave, pitch, roll, warp) characterise the suspension independent of a particular bump. They reveal body and wheel-hop resonances, quantify grip (tyre load variation) vs platform (body motion), and are the basis of 4/7-post rig and on-track damper optimisation.
- Fuel consumption and fuel strategy per stintStrategyL1
- Know your fuel per lap to the decilitre, validate the ECU figure against measured fuel by mass and temperature, and turn it into laps per tank, start fuel, stint lengths and fuel-saving targets.
- Fuel consumption, fuel accounting & lift-and-coastEngineL1
- Know fuel per lap, laps per tank and the lap-time cost of fuel mass; measure fuel by mass with temperature correction; when you must save, lift-and-coast at the end of fast straights is usually the cheapest technique.
G
- Gear ratio fundamentals & tractive effort curvesGearboxL1
- The gearbox keeps the engine inside its power band across the speed range. Tractive-effort curves per gear, compared with the ideal constant-power hyperbola, show what each ratio costs and gains.
H
- Heave / third springs: decoupling heave from rollSprings & ARBL2
- A third (heave) element acts only when both wheels of an axle move together. It lets aero cars hold ride height under downforce with high heave stiffness while roll stiffness and single-wheel compliance are tuned separately.
- Hybrid systems in LMH / LMDh: deployment, energy & brake-by-wireEngineL2
- In Hypercar the hybrid does not add peak power — total power is capped. It changes where energy comes from, which axle drives (LMH above a speed threshold) and how braking torque is split, which makes brake-by-wire a key engineering topic.
I
- Instant centre & roll centreGeometryL1
- The front-view instant centre and the roll centre decide how much lateral load transfer goes through the links rather than the springs, how much the body rolls, and whether the car jacks up in corners.
K
- Kerb riding and high-speed damping controlDampersL2
- Kerbs and big bumps drive shaft velocities to several hundred mm/s. High-speed bump lets the wheel climb without launching the car, high-speed rebound returns it to the ground without bouncing, and the whole package (springs, bump stops, ARBs, ride height) decides whether the car can use kerbs.
L
- Lap time simulation: steady-state, quasi-steady-state, transient, and correlation with dataDataL2
- Simulation lets you test without the track, but only a model correlated against logged data is worth trusting. Learn the simulation levels, the vehicle–tyre–track model structure, how to correlate, and how to use sims before, during and after an event.
- Lateral load transfer and its three componentsWeight transferL1
- Total lateral load transfer is fixed by mass, CG height, track width and lateral g. Suspension only decides how it is split between axles and through which path: unsprung, geometric (roll centre) or elastic (springs/bars).
- Limited-slip types: plate/ramp, viscous, Torsen, activeDifferentialL1
- Plate-and-ramp (Salisbury) diffs lock in proportion to input torque plus a preload; viscous diffs respond to speed difference; Torsen gear diffs to torque ratio; active diffs to a controller. Each has a distinct signature on track.
- LLTD, the "magic number" and mechanical balanceWeight transferL2
- The front share of total lateral load transfer (LLTD) is the main mechanical balance parameter. A commonly quoted starting point is front LLTD about 5 points above static front weight, but the right number depends on tyres, drivetrain, aero and driver.
- Load sensitivity: why load transfer costs gripTyresL1
- Tyre friction coefficient falls as vertical load rises, so an axle with unequal wheel loads makes less total force than the same axle with equal loads. This is the root of LLTD balance tuning and of why downforce gives less than proportional grip.
- Lock-up diagnosis: front vs rear, wheel speed vs reference speedBrakesL2
- Detect and classify lock-ups from wheel speeds against a reliable vehicle reference speed, then separate bias, technique, platform and powertrain causes.
- Longitudinal load transfer, pitch and anti-geometryWeight transferL1
- Braking moves load to the front and acceleration to the rear by m·a_x·h/L. Springs and anti-dive/anti-squat geometry do not change that total; they decide how much pitch it causes, which matters for aero platform, braking stability and traction.
- Low-speed vs high-speed damping: body vs wheelDampersL1
- "Low" and "high" speed refer to damper shaft velocity, not car speed. Low-speed damping controls body motion from driver inputs and aero; high-speed damping controls the wheel over bumps and kerbs.
M
- Math channels: a practical toolboxDataL2
- Math channels turn raw sensor data into engineering quantities: corrected speed, understeer angle, roll gradient, slip ratio, total gear ratio, combined g and delta time. Learn the core set, their assumptions and where they break.
- Measurement fundamentals: ADC resolution, sensor specs and uncertaintyDataL2
- Every logged number is an estimate. Know how ADC resolution and sampling limit what you can see, how to read a sensor data sheet, and how to put an honest uncertainty on a result – including whether a setup change really made a difference.
- Measuring aero on track: coast-down, constant-velocity & logged-data estimatesAeroL2
- Drag from coast-downs, downforce and balance from constant-speed runs with suspension loads, and both from normal laps with the right corrections. Includes a fully worked GT3 straight-line test.
- Motion ratio & installation ratioGeometryL1
- The spring, damper and anti-roll bar never sit at the wheel. The motion ratio converts what they do into what the tyre feels – and because it enters squared, small geometry errors become large rate errors.
O
- Operating windows: temperature, hot vs cold pressure, TPMSTyresL1
- A race tyre only delivers its grip inside a temperature and pressure window. You set cold pressures, but the tyre works at hot pressures, so the engineer’s job is predicting the build-up and verifying it with TPMS.
- Oversteer remedies by phase and speedSetupL2
- Oversteer costs confidence more than lap time on paper – a driver who doesn't trust the rear will not commit. Cure it by phase (entry instability, mid-corner looseness, exit traction) and by speed (mechanical vs aero), and distinguish true balance from traction and platform problems.
P
- Pit stop strategy: pit loss, undercut/overcut, safety cars and FCYStrategyL2
- Pit loss, tyre warm-up and gaps decide whether stopping early (undercut) or late (overcut) gains position. Neutralisations (SC, VSC/FCY, Code 60) change pit loss dramatically – the best calls are prepared before the race.
- Pitch gradient and the aero platformSprings & ARBL2
- Pitch gradient (pitch angle per g of longitudinal acceleration) characterises how the platform moves under braking and traction. On aero cars it drives aero balance changes on entry and exit and is shaped by heave stiffness, bump stops and anti-geometry.
- Platform control & ground effect: diffuser, stall, porpoising, plankAeroL2
- Underbody downforce rises as the car gets closer to the ground — until the flow stalls. Controlling the dynamic platform (heave, pitch, roll) to stay near the peak without crossing the cliff is the core of modern aero setup, and the source of porpoising.
- Power steering & steering torque as a data channelSteeringL2
- Power assistance changes how much of the tyre's message reaches the driver. A steering-torque channel lets the engineer see the front limit, driver effort and system health objectively.
- Preload, ramp angles & friction faces: drive vs coast lockingDifferentialL2
- Locking torque = preload + (friction faces × μ × radius / ramp geometry) × input torque. Lower ramp angles and more faces lock harder; drive and coast are set separately. A worked example puts real numbers on torque bias.
- Putting the driver in the simulation: sim racing and driver-in-the-loopDriverL2
- Offline lap simulations assume a driver at the limit everywhere. Driver-in-the-loop simulators add the human – their perception, confidence and technique – and all the data-analysis methods transfer one-to-one to virtual laps.
R
- Reading tyre temperatures: probes, IR sensors and math channelsTyresL1
- Inner/middle/outer temperatures tell you about camber, pressure and which tyre is working hardest. On-car IR adds corner-by-corner detail and lets you build objective channels: spread, pressure index, workload share and time-in-window.
- Ride frequency and how to choose itSprings & ARBL1
- Ride frequency normalises stiffness by sprung mass so cars of different weight can be compared. Choosing it is a trade between mechanical grip over bumps and aero platform control, with the front/rear ratio shaping pitch behaviour.
- Ride height & rake as geometryGeometryL1
- Ride height is not just an aero number: it sets the operating point of every kinematic curve – roll centre, camber, bump steer, anti percentages. Static and dynamic ride height can differ by tens of millimetres.
- Ride-height sensitivity, rake & aero mapsAeroL2
- On any car with an underbody, downforce, drag and balance depend strongly on dynamic front and rear ride heights. Aero maps capture this; the engineer's job is to place the car's dynamic platform in the right region of the map.
- Roll gradient & roll ratio as setup toolsSprings & ARBL2
- Measure suspension roll from damper pots, regress it against lateral g, and you get front and rear roll gradients and their ratio – objective, lap-by-lap metrics of roll stiffness and its distribution that also flag broken bars and deflating tyres.
- Running a test or practice session: run plans, change discipline and tyre allocationStrategyL2
- Track time is the scarcest resource. A run plan with clear objectives, disciplined one-at-a-time changes, controlled tyre and fuel states, and a baseline check turns a session into knowledge instead of noise.
S
- Self-aligning torque, pneumatic trail & steering feelSteeringL1
- Steering torque comes mostly from the tyre lateral force acting behind the steering axis. Because the tyre's pneumatic trail collapses as it approaches the limit, steering goes light just before the front saturates – the driver's primary understeer cue.
- Sensor technology: temperature, pressure, displacement, acceleration, strain, speed and GPSDataL2
- Choose sensors by asking what, what range, what environment, what accuracy and what budget. Know the working principle and failure modes of the sensors on your car so you can trust – or distrust – their data.
- Sequential gearboxes, paddle shift & what homologation leaves youGearboxL1
- Racing sequential gearboxes use dog engagement, a selector barrel and electronic shift control (cut + blip). In GT3, F2 and similar categories ratios are homologated — but shift calibration, maintenance and monitoring remain the engineer’s job.
- Setup change priority and the tool hierarchySetupL1
- Not all setup changes are equal: they differ in time to make, predictability, scope and side effects. A disciplined hierarchy – tyre pressures → ARB → wing → springs → dampers → geometry – plus correct magnitude and one change at a time keeps a test session productive.
- Setup for track characteristicsSetupL2
- Every circuit pulls the setup in a different direction: bumps want compliance, high-speed tracks want platform and low drag, street circuits want ride height, steering lock and stability, kerb-heavy tracks want controlled high-speed damping, and temperature shifts the tyre window. Start the weekend from the right baseline.
- Slip angle and cornering stiffnessTyresL1
- A tyre only makes lateral force by running at a slip angle. The slope of the force-vs-slip curve (cornering stiffness) sets the car’s linear response, and the peak sets its grip.
- Slip ratio and longitudinal forceTyresL1
- Braking and traction force need the tyre to rotate slightly slower or faster than free rolling. Peak force on dry slicks comes at a slip ratio of roughly 6–12%, and wheel-speed data shows you where the driver and the electronics operate.
- Static toe, front & rearSteeringL1
- Toe pre-loads the tyres with opposing slip angles. Front toe trades turn-in response against straight-line stability; rear toe-in is a primary stability tool. On the straights toe costs almost nothing in drag or heat; its real effects are stability, response and how slip is shared between the loaded and unloaded tyre in corners.
- Steering ratio: steering-wheel angle vs road-wheel angleSteeringL1
- The logged steering channel measures the steering wheel, not the tyres. Knowing the true, non-linear and compliant relationship to road-wheel angle is the basis of every steering-related math channel.
- Steering smoothness and corrections: steering rate and error metricsDriverL2
- Steering traces show both driver technique and car balance. Steering-speed and steering-error metrics quantify smoothness and corrections – but only mean something once you know whether the car is balanced and the driver is at the limit.
T
- The beginner’s logging kit and sensor plausibility checksDataL1
- Learn what the six basic signals and damper pots look like on a good lap, and how to verify sensors with physics – pit-lane steady-state checks, sign conventions and cross-channel consistency.
- The cornering sequence and driving lines: minimum speed, apex placement, V vs U cornersDriverL1
- Every corner is a sequence: braking, turn-in to apex, apex to exit. Use the corner-radius and curvature channels to locate the apex, judge the line, and decide whether a corner should be driven V-shaped (rotate and drive out) or U-shaped (carry speed).
- The g-g diagram and using the friction envelopeWeight transferL1
- Plotting lateral against longitudinal acceleration shows the car’s performance envelope and how much of it the driver uses. It is speed dependent (aero), asymmetric (power, drag) and best analysed in speed bands and with gated grip statistics.
- The gear chart & the total-gear-ratio math channelGearboxL1
- Plot rpm against speed and every sample should fall on one line per gear. The total-gear-ratio math channel turns that into a stepped trace that reveals gear usage, wheelspin, lock-ups and poor down-shift blips.
- The setup sheet, baseline philosophy and back-to-back testingSetupL2
- A setup is only as good as its documentation. Keep a complete setup sheet and run log, work from a known baseline, evaluate changes back-to-back with controlled conditions, and check whether a lap-time difference is statistically real before believing it.
- Throttle application: full-throttle %, throttle acceptance, pickup and hesitationDriverL1
- The throttle is the driver’s primary interface. Histograms, full-throttle time, throttle acceptance, throttle speed and coasting metrics reveal whether a driver is too careful, too aggressive, or fighting the car.
- Throttle maps, pedal maps & drivabilityEngineL1
- With drive-by-wire the pedal is a torque request, not a throttle cable. The pedal map shapes how predictable torque is at small openings — which decides how hard the driver can lean on the rear tyres on exit.
- Time vs distance & the value of corner-exit speedGearboxL1
- A constant time gap looks like a growing distance gap on a straight. Exit speed gains carry down the following straight but decay — by how much depends on whether the car is traction-, power- or drag-limited.
- Torque, power & tractive force: power-limited vs traction-limitedEngineL1
- Engine torque becomes wheel force through the total gear ratio; power sets how much force is available at a given speed. Below a crossover speed the tyres, not the engine, limit acceleration.
- Total wheel loads: aero, transfer and estimation from dataWeight transferL2
- Each tyre’s vertical load is the sum of static weight, lateral and longitudinal transfer, aero load, banking/grade and bump content. You can estimate it from accelerations and setup data, or measure it via damper potentiometers or load cells, as long as you know what each method misses.
- Track data and track characterisationDataL2
- Data tells you what kind of circuit you are at: speeds, gear usage, brake energy, full-throttle share, corner direction balance, g-g quadrant usage and bumpiness. Use these numbers to choose the baseline setup and tyre pressures before turning a wheel.
- Traction control: slip targets, TC maps & cut strategiesEngineL2
- TC keeps driven-wheel slip near the tyre’s peak by cutting torque when measured slip exceeds a target that depends on speed, gear, lateral g and throttle. How it cuts matters as much as when.
- Translating driver language into engineeringSetupL1
- Drivers describe sensations, not mechanisms. The engineer's job is to turn "it won't rotate" or "the rear snaps" into a corner phase, a speed range, an axle and a physical cause – by asking the right follow-up questions and checking the data.
- Tuning the diff from driver feedback & dataDifferentialL2
- Compare the measured rear wheel-speed difference with the kinematic one (track × yaw rate) to see whether the diff is free, locked or letting the inside wheel spin — then link it to the driver’s phase-specific comments.
- Tyre degradation modelling and stint lengthStrategyL2
- Measure how tyres perform over their life during practice long runs, separate degradation from fuel and driver effects, and use a simple model to choose stint lengths and the number of stops.
- Tyre degradation: graining, blistering, thermal vs wear deg, managementTyresL2
- Lap time lost over a stint comes from distinct mechanisms (graining, blistering, thermal degradation, wear) with different signatures and different cures. Diagnose the mechanism before changing the car or the driver’s approach.
- Tyre-driven setup decisionsSetupL2
- Hot pressure targets, temperature-based camber decisions and degradation management turn the tyre from a black box into a setup input. The best setup is the one that keeps all four tyres in their window for the whole stint.
U
- Understeer angle from dataSteeringL2
- Subtract the kinematic (Ackermann) steer angle the car would need at zero slip from the actual road-wheel angle: what remains is the understeer angle – a math channel and a lap statistic for tracking balance over runs, setups and stints.
- Understeer gradient and steady-state cornering (bicycle model)Weight transferL2
- The linear bicycle model defines understeer gradient, neutral steer, characteristic and critical speed. In data it becomes the understeer-angle channel, a powerful balance statistic, provided you remember it is only strictly valid in the linear range.
- Understeer remedies by phase and speedSetupL2
- Understeer is cured differently on entry, mid-corner and exit, and in slow (mechanical) versus fast (aero) corners. Pick the remedy from the phase × speed cell, not from a generic list.
- Up-shift & down-shift analysis: shift points, shift time, blips, over-revGearboxL2
- Optimal upshift rpm maximises the power used between post-shift and shift rpm; shift time is read from the longitudinal-g dip; down-shifts need a correct blip and must be protected against over-rev.
W
- Wet and changing conditions setupSetupL2
- In the wet, grip falls by 30–50%, downforce matters less, standing water threatens aquaplaning and tyre temperatures collapse. Setup moves toward compliance, stability and drivability – and in changing conditions the engineer must manage the crossover between tyre types and setups.
- What a DAQ system is: sensors, logger, ECU and sampling ratesDataL1
- A data acquisition system turns physical quantities into time-stamped numbers. Understanding the chain sensor → conditioning → ADC → logger, and choosing sensible sampling rates, decides whether the data can answer your questions at all.
- Wheel rate, tyre rate & ride rate (springs in series)Springs & ARBL1
- The spring on the damper is not the stiffness the tyre sees. Motion ratio turns spring rate into wheel rate, and the tyre acts as a second spring in series, giving the ride rate that actually sets body frequency.
- Why a differential: the open diff and its inside-wheel limitationDifferentialL1
- In a corner the outside wheel must turn faster than the inside one. An open diff allows that by splitting torque equally — which caps total drive at twice what the weakest (inside) wheel can transmit.
- Wings, Gurneys & dive planes: typical adjustment sensitivitiesAeroL2
- What a wing click, a Gurney or a dive plane actually does to total downforce, balance and drag on GT3 and formula cars — and how to verify it on track despite driver and weather noise.