Learn / Driver Analysis / The cornering sequence and driving lines: minimum speed, apex placement, V vs U corners
L1 · Foundation

The cornering sequence and driving lines: minimum speed, apex placement, V vs U corners

Every corner is a sequence: braking, turn-in to apex, apex to exit. Use the corner-radius and curvature channels to locate the apex, judge the line, and decide whether a corner should be driven V-shaped (rotate and drive out) or U-shaped (carry speed).

The cornering sequence and driving lines: minimum speed, apex placement, V vs U corners: L1 Foundation explanation

The cornering sequence (Segers §7.1):

  1. Braking point to turn-in – straight-line braking; where braking starts fixes where the car can turn and how fast it arrives.
  2. Turn-in to apex – trail braking that blends into a brief, possibly near-zero, neutral-pedal phase (not the same as coasting) to carry speed to the apex.
  3. Apex to exit – the driver goes to full throttle and onto the next straight.

Why exit matters most. Speed out of a corner that leads onto a straight is carried all the way down the straight. Lines should be judged primarily on corners followed by significant acceleration zones.

Minimum corner speed for a given radius RR and grip μ\mu without downforce:

Vmax=μgRV_{max} = \sqrt{\mu g R}

Bigger radius → higher speed, so the fastest line through an isolated corner is the one with the largest radius. But the best line overall depends on what comes before and after.

Speed-trace shapes. Look at the speed trace through a corner:

  • V-shaped: brakes late and deep, short rotation, low minimum speed, early and hard acceleration.
  • U-shaped: brakes earlier/lighter, carries a high minimum speed through a long constant-speed arc, accelerates later.

Neither is universally right; it depends on the car and the corner.

Key formulas

Maximum cornering speed (no aero)
Vmax=μgRV_{max} = \sqrt{\mu g R}
μ\mu
tyre friction coefficient
R
path radius (m)
Maximum cornering speed with downforce
Vmax=μgR1−μρCLAR2mV_{max} = \sqrt{\frac{\mu g R}{1 - \frac{\mu \rho C_L A R}{2m}}}
ρ\rho
air density (kg/m³)
CLAC_L A
downforce coefficient × area (m²)
m
mass (kg)
Path radius and curvature from data
R=V2Glat g,κ=Glat gV2R = \frac{V^2}{G_{lat}\,g}, \qquad \kappa = \frac{G_{lat}\,g}{V^2}
Time value of an exit-speed advantage
Δt≈ΔVeax(Ve)(1−VeVend)\Delta t \approx \frac{\Delta V_e}{a_x(V_e)}\left(1 - \frac{V_e}{V_{end}}\right)
ΔVe\Delta V_e
exit-speed advantage (m/s)
ax(Ve)a_x(V_e)
available longitudinal acceleration at exit speed (m/s²)
VendV_{end}
speed at the end of the straight (m/s)
Traction/power crossover speed
V∗≈Pwheelm ax,tracV^* \approx \frac{P_{wheel}}{m\,a_{x,trac}}
PwheelP_{wheel}
power at the wheels (W)
ax,traca_{x,trac}
traction-limited acceleration (m/s²)
Interactive

Cornering speed with downforce

Solve the steady-state grip-limited cornering speed with and without downforce, including the flat-out case.

Steady-state cornering limit with downforce
mv2R=μ(mg+12ρv2CLA)\frac{m v^2}{R} = \mu\left(m g + \tfrac{1}{2}\rho v^2 C_L A\right)v2=μmgmR−12ρ μ CLAvno aero=μgRv^2 = \frac{\mu m g}{\dfrac{m}{R} - \tfrac{1}{2}\rho\,\mu\,C_L A} \qquad v_{no\,aero} = \sqrt{\mu g R}
If m/R ≤ ½ρμCLA the downforce grows faster than the required centripetal force: the corner is flat-out (limited by power/drag, not grip).
Inputs
Results
Max speed with aero
155.3 km/h
43.14 m/s
Max speed, no aero
142.6 km/h
39.62 m/s
Lateral acceleration
1.90 g
no aero: 1.60 g
Downforce at that speed
250 kg
flat-out above R = 639 m
Radius [m]No aero [km/h]With aero [km/h]Gain [km/h]Lateral [g]
2571.372.71.41.67
50100.9105.04.21.74
100142.6155.312.71.90
200201.7243.341.62.33
400285.3466.3181.04.28
800403.4∞——

Trackside takeaways

  • Judge lines first on corners followed by long acceleration zones – exit speed is carried down the straight.

  • Minimum radius (curvature peak) locates the apex; early peak = late apex, late peak = early apex.

  • Late apex for corners onto straights and decreasing-radius corners; mid apex for constant radius.

  • V-shaped corners suit high power-to-grip cars in slow corners (they stay traction-limited on exit); U-shaped suit high-grip, lower-power cars and fast corners.

  • Analyse compound corners as one sequence with segment times bounded on straights.

On your car

High power and mass, ABS and good traction: V-style in slow corners is usually fastest – brake deep, rotate, straighten early, full throttle.

Check yourself

Question 1 / 4L1 · Foundation

The corner-radius channel shows the minimum radius occurring early in the corner, with lateral g peaking soon after turn-in and then decaying. Which line was used?

Further reading
  • Segers – Analysis Techniques for Racecar Data Acquisition — §7.1 The Cornering Sequence
  • Segers – Analysis Techniques for Racecar Data Acquisition — §14.7 The Driving Line (§14.7.1–14.7.4)
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 1 The Problem Imposed By Racing · minimum time and path
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 9 "g-g" Diagram · acceleration-limit boundary, traction vs power limit
  • Other — Casanova, Sharp & Symonds, "Minimum time manoeuvring: the significance of yaw inertia", Vehicle System Dynamics 34 (2000)
  • Other — Perantoni & Limebeer, "Optimal control for a Formula One car with variable parameters", Vehicle System Dynamics 52 (2014)