Comparing laps: delta time, segment times and track mapping
Find where time is gained or lost before asking why. Delta-time channels, segment times, theoretical best laps and accurate distance alignment are the backbone of every debrief.
Comparing laps: delta time, segment times and track mapping: L1 Foundation explanation
Start with "where", then "why". Performance analysis begins by locating the gain or loss, not by staring at dampers.
Segment (sector) times. Place virtual beacons around the lap – on straights, or splitting corners into entry/apex/exit – and the software tabulates time per segment for every lap. Two derived numbers:
- Theoretical best lap = sum of the best segment times in the run. It estimates the potential of the package. Good drivers in a clean run get within 0.1–0.3 s of it.
- Best rolling lap = fastest full-lap time measured between any beacon pair (not necessarily start/finish). Useful when traffic spoiled every proper lap, because it was actually driven.
Overlays and delta time. Overlay speed traces against distance and add the delta-time channel: the running time difference between two laps at each point of the lap. The slope tells you where time changes; the final value is the lap-time difference.
Track maps. Software builds the map from speed and lateral g (inertial mapping) or GPS. Colour it by braking, throttle or delta to see the lap at a glance.
Comparing laps: delta time, segment times and track mapping: L2 Practitioner explanation
Reading delta time. Define
with the running lap time at distance . Positive and rising means lap B is losing. The slope is the instantaneous loss rate; equivalently
so a speed deficit costs most time where speeds are low. Rule of thumb: a constant speed deficit over a distance at speed costs . Being 2 km/h slower over a 300 m straight at 200 km/h costs ~0.05 s; being 2 km/h slower for 60 m through an 80 km/h hairpin costs ~0.07 s.
Why corner exit matters. An exit-speed deficit persists down the whole following straight (until both cars approach top speed or brake). The delta channel shows this as a steady ramp after the corner – the most valuable losses to fix are therefore exits onto long straights.
Segment pitfalls.
- More segments always give a faster theoretical lap. Segers' Spa example: 7 segments gave a theoretical lap 1.42 s under the best real lap, 3 segments only 0.42 s. Start with few segments, add more where you need detail.
- Beacons placed at apexes make segments sensitive to line variations; place them on straights where possible.
- A line that is faster in one segment may compromise the next – the theoretical lap can be unachievable.
Distance alignment. Distance from wheel speed drifts with lock-ups, wheelspin and tyre radius changes, so the same corner can be offset by several metres. Check alignment with high-rate damper data: road bumps are a fingerprint of the track. If the bump spikes of two laps don't line up, the overlay is misaligned there (Segers shows a 6 m offset after a single lock-up). GPS-fused distance largely removes the problem.
Comparing laps: delta time, segment times and track mapping: L3 Advanced explanation
Delta time is a cumulative integral – read the slope, not the level. A large delta at the end of a sector may come from one 50 m zone; everything after it is flat. Engineers new to data often attribute the whole deficit to the corner where it is displayed largest, rather than where the slope was steep.
Time-slip rate formulation. Some software expresses the loss rate as a percentage speed difference (time-slip rate) and integrates it (time slip). To first order this equals the delta-time channel – Segers notes both give the same result – but the exact slope is , so a 20 % speed deficit costs 25 % more time, not 20 %. Running lap time itself is just the logger time stamp at each distance sample; both methods depend on the same distance alignment, and that alignment is the real accuracy limit.
Alignment strategies:
- Beacon offset – shifts the whole lap; fixes the start but not mid-lap drift.
- Corner-based re-alignment – software stretches distance between identified features (apex minimum speeds, braking points) so each corner aligns.
- Road-profile correlation – cross-correlate high-pass filtered damper signals between laps in windows; the lag that maximises correlation is the distance offset.
- GPS/IMU fused position – best, typically within 1 m with a good receiver and inertial blending.
Missing beacons. Recognisable road features in the damper trace can be used to insert beacons manually when the IR beacon or GPS gate fails, and to sanity-check lap distance (lap distances should match within ~0.5 % on a clean line).
Comparing across conditions. When comparing different runs (fuel, tyres, track evolution), normalise first: fuel-correct lap times, compare like-for-like tyre age, and look for systematic offsets that span the whole lap (grip change) versus local ones (driving or setup). A uniform small positive slope everywhere suggests weight or grip; a localised step suggests a corner-specific issue.
Key formulas
- s
- lap distance (m)
- running lap time of laps A and B at distance s (s)
- V
- local speed (m/s)
- N
- number of segments
- time in segment k (s)
Trackside takeaways
Locate the loss with delta time before investigating its cause.
Read the slope of delta time; the level only accumulates history.
Speed deficits cost most at low speed; exit deficits onto long straights are the most expensive.
More segments = more optimistic theoretical best; place beacons on straights.
Verify distance alignment with damper bump fingerprints or GPS before comparing a specific corner.
On your car
In Pro-Am line-ups, the theoretical best per driver vs the pro reference is a clean coaching KPI; best rolling laps help when practice is full of traffic (40+ car fields).
Check yourself
The delta-time channel (B minus A) rises by 0.25 s through a hairpin and the following 400 m straight, then stays flat. Where should you look first?
- Segers – Analysis Techniques for Racecar Data Acquisition — §3.2 Lap Markers and Segment Times
- Segers – Analysis Techniques for Racecar Data Acquisition — §3.3 Comparing Laps · instantaneous/cumulative variance, time slip, road-profile alignment
- Segers – Analysis Techniques for Racecar Data Acquisition — §3.4 Track Mapping
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 1 The Problem Imposed By Racing · lap-time sensitivity to grip and speed