Throttle application: full-throttle %, throttle acceptance, pickup and hesitation
The throttle is the driver’s primary interface. Histograms, full-throttle time, throttle acceptance, throttle speed and coasting metrics reveal whether a driver is too careful, too aggressive, or fighting the car.
Throttle application: full-throttle %, throttle acceptance, pickup and hesitation: L1 Foundation explanation
More power = thinner margin. Throttle errors come in three pairs – under- or over-application, early or late, slow or abrupt – and every extra kilowatt narrows the window between them.
Basic tools:
- Throttle histogram – % of lap time in each throttle band. Ideal: a tall bar at 100 %, a bar at 0 % (braking), and little in between. A driver with high part-throttle bins is modulating – often "tap-dancing" on the pedal.
- Average throttle per lap – a performance statistic; generally higher = faster.
- Full-throttle time % – time with throttle above ~95–98 % divided by lap time. Segers' Donington example: 63.85 % vs 63.23 % for two drivers whose laps differed by 0.28 s.
- Coasting – neither throttle nor brake (TP < 5 % and brake < 5 bar). Before braking it is always lost time; after braking, a short neutral phase can be deliberate to settle the car.
Classic inexperienced pattern (Segers): the driver brakes too early and too much, realises he is too slow mid-corner, and goes back on the throttle while the tyres are still at maximum lateral load. The driven wheels spin, he lifts, waits – and reaches full throttle later than a driver who carried more entry speed, accepted a lower minimum speed and then went to full power in one smooth motion. The second driver was 2 s per lap faster.
Throttle application: full-throttle %, throttle acceptance, pickup and hesitation: L2 Practitioner explanation
Throttle acceptance. Define, per corner,
– how much lateral load the driver is still using when reaching full throttle. Segers' Donington example: McLean's – peak 1.61 g, full throttle reached at 1.23 g → 76 %; Coppice – similar speed, peak 1.60 g, full throttle at 1.45 g → 91 %. Same driver, same car: he is a bit careful in McLean's. Buddy Fey's targets: ~95 % for cars under ~150 hp, ~80 % above ~400 hp.
A low throttle acceptance means either a careful driver or a car with an exit problem (oversteer or understeer) – check balance channels and ask the driver before coaching. A too-early throttle shows wheelspin, TC intervention, opposite lock and a lift.
Throttle speed (%/s; log throttle at ≥ 20 Hz, preferably 100 Hz). A fluctuating throttle-speed trace on exit means pitch oscillation and tyre-load fluctuation – unsettled exits. For a lap metric, average only the positive values below full throttle so lifts and full-throttle zeros don't bias it.
Pickup and hesitation. Look at the pickup point (first throttle application after the brake) relative to the apex/minimum speed, and for hesitation: a partial lift after pickup, often 10–30 % for 0.2–0.5 s. Hesitation usually means the car didn't feel ready (mid-corner oversteer, poor traction, entry speed too high) or the line was too tight. Map it per corner – the same hesitation every lap in one corner is a car/line issue; random hesitations suggest driver confidence.
Typical full-throttle % (dry, GT3): Monza ~70 %, Spa ~60–65 %, Barcelona ~55 %, Hungaroring ~50 %. Fuel saving drops it a few % (Segers shows a ~5 % deficit for a driver saving fuel to avoid a stop); tyre degradation lowers it lap by lap through a stint.
Throttle application: full-throttle %, throttle acceptance, pickup and hesitation: L3 Advanced explanation
Separating driver and car on exit. Overlay throttle, rear slip ratio (or TC cut/intervention channel), steering and lateral g:
- Traction-limited exit: throttle progressive, slip ratio at the peak-traction value (typically 6–12 % for slicks), TC active – the driver is at the limit; improve car traction (diff, rear ARB, damper, ride height) rather than coaching.
- Balance-limited exit: throttle held part-open while steering is still increasing (understeer) or reducing with corrections (oversteer) – setup issue unless caused by entry speed.
- Confidence-limited exit: low throttle acceptance, no slip, no correction, lateral g already falling – the driver could be more aggressive; show a reference lap.
Throttle speed vs tyre life. Segers shows a pro whose average throttle speed changes little over a stint while adapting modulation to falling grip, and a less experienced driver whose throttle speed falls markedly as tyres degrade – with more lap-time scatter. Run charts of per-lap throttle metrics are a quick indicator of how a driver adapts to degradation.
Power and drivetrain context. Turbo lag, torque maps and TC settings shape throttle traces: a pedal trace is not torque. On drive-by-wire cars compare pedal position with throttle-body position and ECU torque request; on hybrids (Hypercar) the driver's pedal maps to a total torque request split between ICE and MGU. Engine maps can deliberately soften low-pedal torque for driveability.
Building per-corner KPIs. Implement two math channels per corner: max |lat g| held until corner end, and lat g latched at the moment throttle first exceeds 98 %. Export the table per lap and plot throttle acceptance per corner across a qualifying run – Segers' Navarra example shows a driver whose best values in each corner came on different laps: the ideal lap was never put together.
Key formulas
- TP
- throttle position (%)
- lap time (s)
- %/s
Trackside takeaways
High part-throttle histogram bins reveal pedal modulation (“tap-dancing”).
Throttle acceptance ~80 % for high-power cars, ~95 % for low-power cars are reasonable targets.
Low throttle acceptance can be the car (balance/traction) – check slip, TC and steering before coaching.
Hesitation that repeats in one corner is a car/line issue; random hesitation is confidence.
Full-throttle % falls with fuel saving and tyre degradation – compare like with like.
On your car
500+ hp with TC: compare TC intervention per corner between drivers; a driver relying on TC may look aggressive on throttle but lose drive due to power cuts.
Check yourself
Same car, same session: driver A has a lower minimum speed than driver B in a hairpin but is 0.15 s faster to the next braking point. Most likely reason?
- Segers – Analysis Techniques for Racecar Data Acquisition — §14.3 Throttle (§14.3.1 Histogram, §14.3.2 Full Throttle Time, §14.3.3 Throttle Acceptance, §14.3.4 Throttle Speed, §14.3.5 Coasting)
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.2 Traction and Longitudinal Slip; §4.3 TCS and Slip Ratios