Traction control: slip targets, TC maps & cut strategies
TC keeps driven-wheel slip near the tyre’s peak by cutting torque when measured slip exceeds a target that depends on speed, gear, lateral g and throttle. How it cuts matters as much as when.
Traction control: slip targets, TC maps & cut strategies: L1 Foundation explanation
A driven tyre produces longitudinal force only by slipping: the tyre surface moves slightly faster than the road. The slip ratio compares driven-wheel speed to a reference (free-rolling) speed:
Force rises with slip up to a peak — for racing slicks typically around 6–12 % (lower for stiff-carcass, high-downforce tyres, higher for wet tyres) — and then falls off. Beyond the peak the tyre also loses lateral grip, which is why wheelspin on exit turns into oversteer.
Traction control (TC) measures slip continuously and, when it exceeds a target, reduces engine torque until slip returns below target. In Segers' Bosch example, actual slip briefly reaches 6 % against a 4 % target and the system retards ignition until it is back under.
Basic building blocks:
- Reference speed – from the undriven wheels (or vehicle-speed estimate in AWD cars).
- Slip target – a table, e.g. vs speed and gear; often a driver-selectable TC level shifts the whole table.
- Intervention – ignition retard, ignition/fuel cut of some cylinders, or throttle closing.
What TC is not: a cure for a car with poor rear grip. If TC is cutting a lot, the tyres are being asked for more than they have; the lap time is in setup, tyre management or the driver's throttle application. Well-set TC is mostly invisible in the data — brief interventions at the peak — and lets the driver go to full throttle earlier with confidence.
Typical numbers: GT3 TC dials with 8–12 positions; a step is a few percent of slip target. Drivers often reduce TC (less intervention) on new tyres and add it as the rear degrades.
Traction control: slip targets, TC maps & cut strategies: L2 Practitioner explanation
Reading TC in the data (Segers §4.3). Essential channels: driven-wheel speeds (both sides), reference speed, slip target (from the ECU), TC torque reduction or ignition-cut %, throttle/pedal, gear, lateral g.
- Compute your own slip channel, (Segers Eq. 4.13). Better: use the mean of both front wheels to remove the cornering-radius bias of a single front wheel.
- Overlay slip vs target: brief overshoots followed by cuts = TC working. Slip sitting well under target with cuts anyway = target table too conservative or a noisy reference speed.
- Inside-rear slip: with lateral load transfer the inside rear spins first. Separate left/right slip channels show whether the diff is distributing torque or letting the inside wheel go.
TC maps. The slip target is rarely a single number. Typical axes:
| Axis | Why |
|---|---|
| Vehicle speed | at low speed small absolute speed errors give large % slip; targets often higher at low speed |
| Gear | more wheel torque in low gears → faster spin-up, needs earlier/firmer intervention |
| Lateral g / steering | combined slip: allow less longitudinal slip when the tyre is carrying cornering force |
| Throttle / torque request | relax target at small throttle to avoid nuisance intervention |
Most GT3/GT4/LMP2 cars expose two driver dials: TC slip level (how much slip is allowed) and TC cut/aggression (how hard it reduces torque once triggered). Higher slip level = more rotation and drive but more tyre wear; higher cut = smoother but slower recovery of torque.
Cut strategies:
- Ignition retard – fast (next combustion), smooth, but hot exhaust gases; sustained use cooks exhaust, turbo and catalyst.
- Ignition/cylinder cut – very fast, large torque steps, audible "rattle"; harsher on the driveline.
- Fuel cut – slower to act (wall-wetting, port injection), risk of lean cylinders; used for coarse reductions.
- Throttle closing (DBW) – slow (≈ 50–150 ms + manifold), but efficient; used for the base torque level, with ignition for fast trimming.
Pitfalls: TC on a wet track with a front-wheel reference speed that itself locks or aquaplanes; incorrect tyre circumference after a tyre change (a 1 % circumference error is a 1 % slip offset!); and reading "TC active" as "car has no traction" when it is only trimming peaks.
Traction control: slip targets, TC maps & cut strategies: L3 Advanced explanation
Control loop structure. A typical engine-based TC is a PI(D) controller on slip error with a feed-forward term:
plus a torque ramp-back rate after intervention. The trade-off: aggressive gains cut slip overshoot but cause limit cycles (torque oscillating at 3–8 Hz, felt as "rattle" and often visible in longitudinal g). The driveline torsional mode (half-shafts + tyre longitudinal stiffness, typically 5–15 Hz) limits the usable bandwidth: cutting faster than that excites the mode and makes slip oscillate.
The slip target should follow the tyre, not the other way round. The slip at peak depends on load, temperature, wear and combined lateral slip. With high lateral force, the friction-circle reduces longitudinal capacity; the peak shifts and the post-peak drop becomes steeper. A lateral-g axis that lowers the slip target at high prevents the TC from allowing the slip that would destroy lateral grip at the rear — the main cause of TC-on oversteer.
Reference speed challenges.
- Single front wheel: in a 50 m radius corner with 1.6 m track, inside and outside front speeds differ by ≈ 3 %. A single-wheel reference gives ±1.5 % slip bias left vs right-hand corners.
- Under braking or trail braking the fronts slip negative; TC reference must not be used while braking.
- AWD (LMH above deployment threshold): no free-rolling wheel. Reference is estimated by fusing wheel speeds, IMU longitudinal acceleration and GPS; errors here directly become TC errors.
Choosing a TC level as an engineer. Use a matrix: per corner, compute (a) peak slip on exit, (b) TC torque reduction integral (Nm·s), (c) time from apex to full throttle. Plot each against TC level from a test. The fastest setting usually has small but non-zero intervention integral. Over a stint, track TC intervention per lap as a rear degradation proxy: rising intervention at constant TC level means the rear is going off — that is information for strategy as well as for the driver's TC dial.
Traction control: slip targets, TC maps & cut strategies: L4 Expert explanation
Engine-based TC vs brake-based TC vs diff. Engine torque reduction acts on the axle sum; it cannot separate left and right. If only the inside rear is spinning, an engine cut reduces both wheels’ torque, sacrificing outside-wheel drive force that the tyre could have used. Brake-based TC (common in road cars, rare and often banned in racing) applies the inside brake, mimicking a locked diff. In a racing car the differential locking does this job mechanically — which is why diff setup and TC calibration must be done together: a more open diff produces more inside-wheel spin and more TC activity, a more locked one gives less TC but more power-on understeer/oversteer transitions.
Ignition retard thermal budget. Retard reduces torque by moving combustion late; the energy goes into exhaust heat. 30° retard for a couple of seconds per corner across a lap can raise EGT by 50–100 °C and turbine inlet temperature beyond limits; ECUs include a retard budget that switches to cylinder cut when exhaust temperature is high. When TC "feels different" late in a stint, check whether the strategy switched modes.
Torque-domain TC (hybrids). In a hybrid, an MGU on the driven axle can modulate torque within milliseconds and with no thermal penalty — and on an LMH front axle it effectively becomes a per-axle torque controller. Regulation limits (deployment threshold, ramp rates, total power cap) are written precisely to stop this becoming a full torque-vectoring traction system.
Limits of the slip-target model. Peak-μ slip is not constant: transient exits pass through the curve faster than the tyre's relaxation length allows equilibrium (relaxation length ~ 0.3–0.6 m longitudinally). At low speed, the tyre's slip response time is longer and the controller can overshoot. Good calibrations therefore use a slip-rate term (the derivative) as an early trigger rather than raising gains.
Key formulas
Trackside takeaways
Slicks peak at roughly 6–12 % slip; TC holds slip near a target that should drop when the tyre is carrying lateral load.
A tyre circumference error of 1 % is a 1 % slip offset — update TC/logger rolling circumference after tyre changes.
TC level = how much slip is allowed; TC cut/aggression = how hard it reduces torque. Tune them separately.
Rising TC intervention per lap at the same level is a rear-tyre degradation indicator.
Ignition retard is smooth but heats the exhaust; cylinder cut is fast but harsh.
Diff locking and TC must be tuned together: inside-rear spin triggers engine-wide cuts.
On your car
Bosch/Magneti/Cosworth-based TC with typically 8–12 driver positions plus a separate cut/aggression dial on many cars. Drivers adjust per stint phase and per tyre condition.
Check yourself
Only the rears are changed: a worn pair is replaced by a new pair whose rolling circumference is 1.0 % larger (more tread). The fronts, which give the reference speed, stay on, and nobody updates the TC/logger rear circumference. What happens?
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.2 Traction and Longitudinal Slip · slip ratio definitions, sensor configurations, Eq. 4.11–4.13
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.3 TCS and Slip Ratios · Bosch ASR example, nominal slip vs actual slip, ignition angle during ASR, driven-wheel speed from rpm (Eq. 4.14)
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior · longitudinal slip characteristics
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking