Balance of Performance: restrictors, boost, power & energy limits, weight
BoP equalises different cars with restrictors, boost tables, power caps, energy per stint and minimum weight. Each lever changes a different part of the performance envelope — and therefore which setup and strategy decisions are optimal.
Balance of Performance: restrictors, boost, power & energy limits, weight: L1 Foundation explanation
In GT3, GT4, TCR and the WEC/IMSA prototype classes very different cars race together. Balance of Performance (BoP) adjusts each model so lap times converge. The main levers:
| Lever | Typical use | What it changes |
|---|---|---|
| Air restrictor diameter | NA GT3/LMP | caps air mass flow → caps peak power, flattens the top of the power curve |
| Boost pressure table vs rpm | turbo GT3/TCR | sets torque/power curve directly |
| Power cap / power-speed curve | Hypercar | maximum total powertrain power, sometimes different above/below a speed |
| Energy per stint | WEC Hypercar, LMGT3 | maximum energy usable between refuels (MJ) |
| Minimum weight / ballast | everywhere | mass; often with prescribed ballast position |
| Fuel tank capacity / refuel time | endurance | stint length, pit time |
| Ride height, wing range | some GT series | aero performance |
A restrictor works because once the airflow through the throat reaches the speed of sound (choked flow), mass flow cannot increase however hard the engine pulls. Since power ∝ air mass flow, max power ∝ throat area ∝ : on a 30 mm restrictor, +0.5 mm is about +3.4 % peak power.
For the engineer BoP is a boundary condition, not something to argue about at the track. When BoP changes, many optimal choices change with it: wing level, gearing, shift points, ballast placement, brake balance, fuel strategy. Knowing which lever moved tells you what to re-optimise.
Balance of Performance: restrictors, boost, power & energy limits, weight: L2 Practitioner explanation
How each lever changes your decisions.
Less power (restrictor/boost/cap):
- The car becomes power-limited at lower speed; drag now costs relatively more lap time → re-evaluate wing angle (less downforce may now be faster on long-straight tracks — check with lap sim sensitivity, not intuition).
- Shift points: a restrictor flattens the power curve above choke rpm , so upshifting earlier can cost nothing — but only as long as the rpm after the shift stays on the plateau, i.e. (gear step). Shift earlier than that and the engine drops below the plateau and loses drive force (see the shifting lesson). Turbo boost tables shape torque over rpm — re-derive optimum shift points from the new curve.
- Gearing: with fixed homologated ratios you cannot follow, so the top-gear rpm at end of straight changes; check limiter hits in tow.
More weight (ballast):
- Lap time grows roughly as 0.1–0.3 × the relative mass change: on a 2-minute lap with a 1300 kg GT3, +30 kg (+2.3 %) costs ≈ 0.3–0.8 s before tyre effects. Treat this as an order of magnitude and get the exact sensitivity from your lap sim — it is track-dependent (stop-and-go tracks are more mass-sensitive).
- Ballast location is often prescribed (passenger floor), but if it is free, place it low and where it corrects the weight distribution you want.
- Springs/dampers: +40 kg on a 1300 kg car is +3 % mass — ride frequencies drop by ~1.5 %; usually no change needed, but brake balance and tyre temperatures move slightly.
Energy per stint (WEC):
- The car must not exceed X MJ between refuels. Energy is spent at full throttle; the engineer converts it into a per-lap energy target and coaches lift-and-coast or chooses maps to hit it.
- It makes efficiency a performance parameter: lower drag reduces energy per lap at the same lap time; that is why low-drag setups often win in energy-limited races even if single-lap pace is lower.
Turbo cars and ambient: cars whose ECU controls charge mass or torque hold power with altitude and temperature by raising boost (until the compressor/turbo-speed limit); restrictor cars lose power as falls. Even a turbo car loses a little on a hot day: with a fixed pressure target the charge temperature after the intercooler rises with ambient, charge density falls and knock margin shrinks (ignition retard). BoP often includes ambient corrections; check which ones apply to your car.
Pitfalls: don't compare "your" power with competitor data from a different BoP version or event; most series publish BoP per event — archive it with the setup sheet.
Balance of Performance: restrictors, boost, power & energy limits, weight: L3 Advanced explanation
Choked-flow physics. For isentropic flow of a perfect gas through a throat of area with upstream stagnation pressure and temperature , once the throat Mach number reaches 1:
For air (, J/kg·K) at 1.013 bar, 25 °C, a 30 mm throat with passes ≈ 0.16 kg/s. At λ ≈ 0.9 (AFR ≈ 13.2) and ≈ 35 % brake efficiency this supports roughly 180–190 kW — two such restrictors for a typical V8 GT3 is consistent with ≈ 370 kW.
Consequences:
- Power ∝ , ∝ , ∝ . Restricted engines lose power with altitude and heat; a hot day (+20 °C) costs ≈ 3 %.
- Above the rpm at which the restrictor chokes, the engine cannot breathe more air: power becomes flat with rpm, torque falls as 1/n. The earliest no-loss upshift is (gear step), so that post-shift rpm stays on the plateau; revs above that buy nothing but wear and fuel, revs below it cost drive force.
- Engine developers then chase efficiency (thermal and volumetric) — which is why BoP authorities also monitor torque sensors.
Power caps and torque sensors (Hypercar). Rather than restrict air, the regulations cap delivered power measured by FIA torque sensors on the driveshafts, and specify a power-speed curve — BoP can change the power above a speed (e.g. 250 km/h) separately. This allows the authority to tune straight-line speed independently of acceleration. Engineering consequence: with a hard power cap, the total drive force at speed is fixed; lap time comes from drag, cornering and traction — exactly the opposite of an unrestricted formula car where power is the dominant variable.
Energy per stint vs fuel tank. Energy-limited racing is an optimisation with a budget: minimise subject to . The marginal cost (seconds per MJ) must be equal at all places on the lap at the optimum — that is the formal reason lift-and-coast belongs at the end of the longest, fastest straights, where the time cost per MJ saved is smallest.
Key formulas
- LHV
- fuel lower heating value (≈ 43 MJ/kg)
- AFR
- air–fuel ratio (≈ 13–14.7)
- brake thermal efficiency (≈ 0.33–0.45)
Trackside takeaways
Restrictor power ∝ d²: +0.5 mm on 30 mm ≈ +3.4 % peak power.
Restricted engines go flat above choke rpm: upshift as early as possible while keeping post-shift rpm on the plateau (n_shift ≥ n_choke × gear step); revs beyond that buy nothing.
Less power → drag matters more; re-check wing level and gearing after every BoP power change.
Mass sensitivity: lap time rises ≈ 0.1–0.3 × the relative mass increase — get the exact, track-specific number from the sim.
Energy-per-stint racing rewards efficiency: low drag and well-placed lift-and-coast.
Archive the event BoP with every setup sheet; data comparisons across BoP versions are meaningless otherwise.
On your car
SRO/IMSA/WEC BoP via restrictor or boost table, weight, sometimes ride height and fuel/refuel parameters. Teams cannot change the engine — the engineering response is wing, ballast placement within rules, shift points and strategy.
Check yourself
An NA GT3 car has its twin restrictors reduced from 32.0 mm to 31.0 mm. Approximate change in peak power?
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.1 Torque and Horsepower · power and drag relations used for BoP sensitivity
- Segers – Analysis Techniques for Racecar Data Acquisition — §16.1 Fuel Consumption · fuel/energy accounting used under energy limits
- Other — FIA WEC / SRO / IMSA BoP bulletins · check per event; values change