Fuel consumption, fuel accounting & lift-and-coast
Know fuel per lap, laps per tank and the lap-time cost of fuel mass; measure fuel by mass with temperature correction; when you must save, lift-and-coast at the end of fast straights is usually the cheapest technique.
Fuel consumption, fuel accounting & lift-and-coast: L1 Foundation explanation
Three questions every race engineer must answer before the race (Segers §16.1):
- Fuel per lap — in racing we think in litres (or kg) per lap, not L/100 km.
- Laps per tank — sets stint length, pit-stop count and pit windows.
- Weight penalty — how much each kg of fuel costs in lap time, and how the balance changes as the tank empties (CG height drops; if the tank is not central, weight distribution moves).
Where the number comes from. The ECU knows total injector opening time; the logger/dash multiplies it by an injector flow-rate scalar to give fuel used. This calculation must be calibrated against reality: weigh the fuel in and out (with temperature) and correct the fuel-used calculation scalar — not the ECU's fuelling injector characterisation, which sets pulse width and would change lambda. Segers' GT example: 107.1 L actually used, the logged fuel-used figure said 106.2 L (99.1 %) — the scalar is adjusted so that the dash fuel figure is trustworthy for the race.
Why weigh, not measure volume? Fuel density changes with temperature, roughly 0.1 % per °C. Fuel at 15 °C vs 40 °C differs by ≈ 2.5 % in volume for the same mass: on a 100 L tank that's 2.5 L — about one lap of a GT car.
Typical numbers.
| Car | Fuel per lap (≈ 4–5 km lap) |
|---|---|
| GT3 | 2.5–4 L |
| GT4 | 2.5–3.5 L |
| LMP2 | 2–2.7 L |
| F3 | 1.5–2 L |
Lap-time cost of fuel: a useful scaling is that lap time grows by roughly 0.1–0.3 × the relative mass increase. For a ≈ 1300 kg GT car on a 2-minute lap that is ≈ 0.01–0.03 s per kg per lap; for a ≈ 800 kg formula car on a 90 s lap ≈ 0.03 s/kg. Carrying 10 kg more fuel than needed therefore costs ≈ 0.1–0.3 s every lap — get your car's exact figure from the lap sim.
Lift-and-coast (L&C): the driver lifts off the throttle some distance before the normal braking point, coasts, then brakes a bit later/softer. Fuel is saved during the coast (injectors cut on overrun) at the moment where the car is fastest, accelerates least and is about to brake anyway — so it costs very little lap time per litre saved.
Fuel consumption, fuel accounting & lift-and-coast: L2 Practitioner explanation
Fuel accounting (calibrating the fuel-used calculation). Procedure from Segers:
- Weigh fuel added before and during the session and fuel drained after (scale accurate to ±10 g), and measure temperature each time.
- Fuel mass used = in − out (mass is temperature-independent).
- Convert to volume with the temperature-dependent density, compare with the logged fuel-used total.
- Correct the fuel-used calculation scalar in the logger/dash (not the ECU fuelling injector characterisation, which would change lambda): .
Remember in/out laps use less fuel; extract race-pace consumption per lap only once the total is validated.
Fuel needed for a stint/race:
with a safety margin (1–3 %), plus the regulation sample/reserve (e.g. ~1 L or a minimum mass must remain for scrutineering — check rules) and formation/safety-car laps (SC laps use ≈ 40–60 % of a race lap).
Fuel-saving techniques, in order of time cost per litre (cheapest first, usually):
- Lift-and-coast before the big braking zones, especially from high speed.
- Leaner fuel map (if permitted): λ 0.88 → 0.95 saves several % fuel with ~1 % power loss.
- Short-shifting (upshift earlier): engine runs at lower rpm, lower friction/pumping; on a flat-topped (restricted) power curve almost free as long as post-shift rpm stays on the plateau.
- Higher gear in slow corners — costly if traction-limited exits suffer.
- Lower apex speeds / earlier braking — the most expensive, avoid.
Lift-and-coast in practice. Define it as coast distance (m) or lift point marker before each target braking zone. Measure saved fuel per lap with the ECU fuel channel; measure time lost per lap with a delta. Typical outcome: coasting 50–100 m before two or three big stops saves 2–5 % fuel at a cost of 0.1–0.3 s per lap.
Data: overlay throttle and speed; L&C appears as throttle = 0 with brake = 0 before the braking point. Check consistency lap to lap (the dash "fuel target / delta" helps the driver).
Balance effect: L&C reduces brake temperatures and moves weight transfer earlier — some drivers find entry balance changes; also tyre temperatures drop, which can matter in cold conditions.
Fuel consumption, fuel accounting & lift-and-coast: L3 Advanced explanation
Why lift-and-coast is cheap. Let the car be at speed near the end of a straight with full-throttle acceleration (small near terminal speed) and coasting deceleration (drag + engine braking + rolling, large at high speed). Coasting for a short distance before the braking point:
- Fuel saved ≈ (full-throttle fuel flow × time coasted, overrun fuel cut ≈ 0).
- Time lost ≈ the integral of the speed deficit, . The speed deficit grows with ; but at the braking point the car is slower, so the subsequent braking distance shrinks — the driver brakes later, recovering part of the loss.
Because scales as for small coast distances (deficit grows linearly from zero) while fuel saved scales as , the first metres of coast are almost free and the marginal cost rises with coast length. The optimum distributes coasting over several straights so the marginal cost is equal everywhere — the same principle as energy-per-stint optimisation.
Numbers (GT3, 400 kW, BSFC ≈ 260 g/kWh): full-throttle flow ≈ 104 kg/h ≈ 0.029 kg/s ≈ 0.039 L/s. At 250 km/h, coast deceleration ≈ 2–3 m/s². One second of coast (≈ 70 m) saves ≈ 0.04 L and costs on the order of 0.02–0.04 s — roughly 0.5–1 s per litre saved. Short-shifting usually costs more per litre on non-restricted engines; leaner mapping can be cheaper where available.
Fuel mass effect on lap time. Sensitivity comes from the sim or from two runs with known fuel difference (correcting for tyre state). It is not linear with lap length alone: tracks with many slow corners and long acceleration phases are more mass-sensitive. Use it to:
- pick qualifying fuel (minimum needed + margin),
- compute fuel-corrected lap times for degradation analysis: .
Density. Gasoline thermal expansion coefficient ≈ 0.00095–0.0012 /K. With ρ15 ≈ 0.75 kg/L: . For energy-limited formulas, the sensor reads energy via fuel flow × calorific value; fuel batch LHV variations (≈ ±0.5 %) are part of the regulator's tolerance.
Key formulas
- lap-time sensitivity to mass (s/kg)
- current fuel mass (kg)
Fuel & stint planner
Plan stints, pit stops and start fuel for a race, and find the fuel saving per lap needed to drop one stop.
| Stint | Laps | Fuel used [L] | Fuel added before [L] | Refuel time [s] |
|---|---|---|---|---|
| 1 | 31 | 111.6 | 113.6 (start) | — |
| 2 | 30 | 108.0 | 108.0 | 36.0 |
| 3 | 30 | 108.0 | 108.0 | 36.0 |
Stints split evenly; start fuel is the first stint plus margin (lighter car), each stop adds the next stint's fuel (car arrives with the margin left). Pit-lane time loss and tyre changes are not included.
Trackside takeaways
Measure fuel by mass and temperature; calibrate the logger/dash fuel-used scalar against the drain (never the fuelling injector data).
Fuel volume changes ≈ 0.1 %/°C — 25 °C difference on 100 L is about a GT lap of fuel.
Each extra kg costs ≈ 0.01–0.03 s/lap in a GT car (≈ 0.03 s in a light formula car); don’t carry more than the stint needs.
Lift-and-coast at the end of fast straights is usually the cheapest saving; first metres are nearly free.
Spread fuel saving over several straights — equal marginal cost everywhere.
Safety-car laps use ~40–60 % of a race lap: include them in the plan.
On your car
Endurance: stint length set by tank (≈ 100–120 L) and/or BoP-defined refuel time or stint energy. Sprint: fuel load matters for qualifying and mandatory minimum fuel at the end.
Check yourself
You drain 25.0 kg of fuel at 38 °C. The fuel has ρ₁₅ = 0.750 kg/L and an expansion coefficient β = 0.0010 /K. What volume did you drain?
- Segers – Analysis Techniques for Racecar Data Acquisition — §16.1 Fuel Consumption · fuel-used calculation, weighing with temperature correction, flow-rate scalar, laps per tank
- Segers – Analysis Techniques for Racecar Data Acquisition — §16.2.1 Fuel Load Variation · fuel mass effect on lap time
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.5 The Importance of Corner Exiting Speed · speed deficit vs time along a straight