Learn / Engine & Hybrid / Throttle maps, pedal maps & drivability
L1 · Foundation

Throttle maps, pedal maps & drivability

With drive-by-wire the pedal is a torque request, not a throttle cable. The pedal map shapes how predictable torque is at small openings — which decides how hard the driver can lean on the rear tyres on exit.

Throttle maps, pedal maps & drivability: L1 Foundation explanation

In almost every modern racing car the throttle pedal is a sensor. The ECU reads pedal position and, through a pedal map, decides what throttle-blade angle (or what engine torque) to deliver. The driver does not feel the engine directly; they feel the map.

Why maps exist: a throttle butterfly is extremely non-linear. At low rpm, the first 15–20 % of blade angle can already produce 60–80 % of the available torque, while the last 50 % adds almost nothing. A 1:1 pedal-to-blade relation would make the car "binary" on corner exit: tiny pedal movements, large torque steps, rear tyres overwhelmed.

A good pedal map makes wheel torque roughly linear with pedal travel — or deliberately progressive at small openings — so the driver can meter torque precisely at the point where the rear tyres are combined-loaded (lateral + longitudinal).

Typical options on a GT or prototype steering wheel:

  • Dry / race map – close to linear torque vs pedal.
  • Wet map – softer initial response, sometimes reduced peak torque in low gears.
  • Fuel-save / lean maps – less fuel per stroke, sometimes lower torque.
  • Qualifying / push maps where permitted.

Key vocabulary:

  • Pickup / tip-in – the moment of going from 0 to partial throttle. A snappy pickup unsettles the car mid-corner.
  • Overrun / engine braking – the torque when the pedal is released. Too much braking torque can lock the rear inside wheel on entry; too little makes the car feel like it "runs on".
  • Throttle lag – delay between pedal and torque (turbo spool, manifold filling, DBW motor speed).

When a driver says "the car is snappy on power" the cause may be the chassis — or the first 10 % of the pedal map. Always check the map before you change the rear end.

Key formulas

Torque-demand pedal map
Treq(p,n)=Tmax(n) g(p),g(0)=0,  g(1)=1T_{req}(p, n) = T_{max}(n)\, g(p), \quad g(0)=0,\; g(1)=1
Wheel torque from engine torque
Tw=Te itot ηT_w = T_e\, i_{tot}\, \eta

Trackside takeaways

  • The pedal is a torque request — the map, not the engine, is what the driver feels on pickup.

  • Throttle blades are highly non-linear at low rpm: build maps as blade angle = f(pedal, rpm).

  • Rain maps should soften the first 30–40 % of pedal, not just cap peak torque.

  • Overrun/engine-braking calibration changes effective brake balance and diff coast locking.

  • Check the pedal map and tip-in filtering before changing the rear suspension for a "snappy on power" complaint.

On your car

Homologated maps; usually several pedal-map positions selectable on the wheel (dry/wet/fuel). BoP changes in boost or restrictor can change the feel of the same map.

Check yourself

Question 1 / 4L1 · Foundation

With a pedal-to-blade relation of 1:1, why does a car often feel "on/off" on slow corner exits?

Further reading
  • Segers – Analysis Techniques for Racecar Data Acquisition — §4.2–4.3 Traction, TCS and Slip Ratios · throttle application vs slip on exit
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking
  • Other — Bosch Motorsport / MoTeC ECU documentation · drive-by-wire torque structure, pedal maps