Torque, power & tractive force: power-limited vs traction-limited
Engine torque becomes wheel force through the total gear ratio; power sets how much force is available at a given speed. Below a crossover speed the tyres, not the engine, limit acceleration.
Torque, power & tractive force: power-limited vs traction-limited: L1 Foundation explanation
Torque is what the engine produces at the crank; force at the contact patch is what accelerates the car. The link is the total gear ratio (gearbox ratio × final drive) and the loaded rolling radius:
Power is force times speed, . At a given road speed, the maximum force you can put down is set by power, not by peak torque: the gearbox lets you trade engine rpm for wheel force, and the best you can do at speed is . That is why engineers talk about power and gearing together, and why "a torquey engine" is mostly a statement about the shape of the power curve.
There is a second ceiling: the tyres. The driven tyres can only produce of longitudinal force. At low speed, is huge, so the engine could deliver far more force than the tyres accept — the car is traction-limited. As speed rises, falls until it drops below the tyre limit; from there the car is power-limited.
Typical GT3 numbers (≈1300 kg with driver, ≈400 kW at the crank, ~57 % rear weight, slicks μ ≈ 1.5):
| Value | |
|---|---|
| Max rear-tyre drive force (static rear load) | ≈ 10.9 kN |
| Max rear-tyre drive force (with load transfer, see L3) | ≈ 14.5 kN |
| Power available at the wheels (η ≈ 0.9) | ≈ 360 kW |
| Crossover speed | ≈ 33 m/s (119 km/h) static, ≈ 25 m/s (89 km/h) with load transfer |
| Accel at 250 km/h (drag ≈ 2.9 kN, ≈ 1.0 m²) | ≈ 0.16–0.18 g |
So in a straight line a GT3 is traction-limited in 1st and much of 2nd gear, and power-limited above roughly 90–120 km/h; on a corner exit, where the rears still carry lateral force, it stays traction-limited to higher speed. A Hypercar (≈ 470 kW/t, BoP-capped) or an F2 car (≈ 580 kW/t, and no TC to help) stays traction-limited to considerably higher speed; a Tatuus F4 (≈ 230 kW/t) becomes power-limited soon after slow exits.
Why it matters trackside: in the traction-limited zone, more power does nothing — traction control, differential, rear grip and driver throttle application decide lap time. In the power-limited zone, power, drag and gearing decide it.
Torque, power & tractive force: power-limited vs traction-limited: L2 Practitioner explanation
Measuring wheel power from data (Segers §4.1). You do not need a chassis dyno: speed and longitudinal acceleration give it. The power used to accelerate the mass is
and the total wheel power adds drag and rolling resistance, . Build it as a math channel and plot it against rpm on full-throttle samples only (throttle > 98 %, gear stable, no shift, |lat g| < 0.2). Segers' Viper example recovered the flywheel torque to within ~6 % — the rest being driveline loss.
Pitfalls that fake a "down on power" engine:
- Gradient: 1 % uphill costs ≈ 0.01 g, i.e. ≈ 128 N, or ≈ 3.5 kW at 100 km/h (≈ 9 kW at 250 km/h) for a 1300 kg car — 1–2.5 % of a GT3's wheel power, the same size as the effect you are trying to detect. Compare the same straight, not different ones.
- Wind and tow: always compare several laps; a tow at 250 km/h is worth several percent of drag.
- Air conditions: NA and restricted power scales ≈ (choked flow for restrictors; the SAE J1349-type correction for NA engines), not with density: +20 °C costs ≈ 3 %, a 30 hPa lower barometer ≈ 3 %, 1000 m altitude ≈ 10 %. Turbo engines compensate up to the turbo limit (minus some knock/charge-temperature loss), restricted engines do not.
- Mass factor: rotating inertia. Segers uses (road-car derived); in low gears this is 10–25 % of the mass, so ignoring it underestimates engine power in 1st/2nd and makes the power curve look as if it rises with gear.
Recognising which regime you are in. Plot vs for full-throttle sections:
- Traction-limited: roughly flat (or rising with downforce) while driven-wheel slip ratio sits at the TC target (5–10 %) or TC is cutting.
- Power-limited: constant (a hyperbola), minus drag. Slip ratio falls to 1–3 %.
What to change. Traction-limited corners respond to rear grip (tyre pressures/temps, rear roll stiffness, diff drive locking, TC map, exit line). Power-limited sections respond to drag (wing, rake), shift points and gearing. A common mistake is to chase exit traction with setup in a corner where the car is already power-limited by second gear — the data will show low slip and no TC activity; the time is in the straight, not the exit.
Top speed sensitivity. Drag power rises with : +10 % top speed needs ≈ +33 % power. Conversely an engine 3 % down only loses ≈ 1 % top speed, but it loses 3 % of tractive force over the whole power-limited range. Net acceleration is , so that is ≈ 3 % of acceleration at low speed but 5–10 % of net acceleration near the end of the straight (≈ 7 % at 250 km/h for a GT3). Check the mid/late-straight speed gradient, not just the speed trap.
Torque, power & tractive force: power-limited vs traction-limited: L3 Advanced explanation
Traction limit with load transfer. For a rear-wheel-drive car of mass , wheelbase , CG height , CG-to-front-axle distance (static rear fraction ) and driven-tyre friction , longitudinal load transfer adds to the rear axle:
With , , m, m and no aero, g in pure straight-line, against 0.86 g from static load alone. The higher traction ceiling (≈ 14.5 kN instead of 10.9 kN for a 1300 kg car) lowers the straight-line crossover from ≈ 119 km/h to ≈ 89 km/h with 360 kW at the wheels. For front-wheel drive (TCR) the sign flips — load leaves the driven axle — so ; with 62 % front weight that gives ≈ 0.75 g. That structural deficit is why TCR cars live on front diff locking and why their exit traction is so sensitive to kerbs.
On a corner exit the tyre is also carrying lateral force: with a friction-ellipse approximation the available drive force is . At 80 % of lateral capacity only 60 % of the drive force remains, and the inside rear is lighter still. Since , a lower available drive force means a higher crossover speed (×1/0.6 ≈ 1.7 in that example). That is why the crossover speed you calculate in a straight line is a lower bound for corner exits: with the tyre still carrying lateral force, the car stays traction-limited up to a considerably higher speed and gear.
Aero moves the crossover. Rear downforce grows with , so the traction ceiling rises with speed. For a high-downforce prototype the traction curve and the curve can run nearly parallel through 3rd–4th gear — the car is "on the edge of traction" for a long time, which is where driver throttle modulation and TC calibration earn the most.
Equivalent mass and gear choice. The rotating inertia reflected to the wheel is (engine + flywheel + clutch + gearbox input), plus wheel and drive-shaft inertia. Because it scales with , a short 1st gear loses a significant part of its torque advantage to spinning up the engine. When comparing gearing options in a sim, model equivalent mass per gear; otherwise you will systematically over-predict the benefit of short ratios.
Data method: power curve from the lap. Bin by rpm (200 rpm bins), keep the upper envelope (the 90th percentile of each bin rejects TC cuts and shifts), and overlay with the dyno curve. A consistent offset = driveline loss or air conditions (p/√T); a shape change at a particular rpm = intake/exhaust or a restrictor reaching choke; a change only in hot laps = knock-control or IAT-related ignition retard.
Key formulas
- engine torque (Nm)
- total ratio = gear × final drive (–)
- driveline efficiency (≈0.88–0.93)
- r
- loaded rolling radius (m)
- P
- engine power (W)
- v
- vehicle speed (m/s)
- driven-tyre longitudinal friction
- driven-axle load incl. load transfer and aero (N)
Trackside takeaways
At a given speed, power — not peak torque — sets the maximum drive force: F = Pη/v.
Below the crossover speed (~90–120 km/h straight-line for a GT3, higher on a combined-slip exit) the tyres limit acceleration; more power is wasted there.
+10 % top speed needs ~+33 % power; an engine down 3 % mainly shows as slower mid/late-straight acceleration.
Wheel power can be measured from speed + long g; compare the same straight, several laps, and correct for air conditions (≈ p/√T).
In traction-limited corners work on rear grip, diff and TC; in power-limited sections work on drag and gearing.
On your car
≈300 kW/t. Traction-limited in 1st/2nd on slow exits; power-limited from ~90–120 km/h in a straight line, somewhat higher on exits that still carry lateral g. BoP power changes therefore matter mostly on medium/high-speed exits and straights.
Check yourself
RWD GT3: 1300 kg, 58 % static rear weight, CG height 0.48 m, wheelbase 2.75 m, rear-tyre μ = 1.45, 350 kW at the wheels, no aero, straight line. Up to what speed is it traction-limited?
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.1 Torque and Horsepower · Wheel torque/power from logged data, mass factor, Viper example
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.1.1 Aerodynamic Drag · v³ power–speed relation
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.2 Traction and Longitudinal Slip
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking