Damper velocity histograms, box plots and run charts
The shock-speed histogram characterises each damper as installed on the car. Symmetry, zero-bin height, % time in low/high-speed bump and rebound, and statistics like standard deviation, skewness and kurtosis turn it into objective metrics you can track lap by lap.
Damper velocity histograms, box plots and run charts: L1 Foundation explanation
A picture of what each damper does over a lap
Take the damper velocity channel for one corner over a lap and count how much time it spends in each velocity bin (e.g. 5 mm/s bins from −300 to +300 mm/s). That's the shock-speed histogram (a method pioneered by Claude Rouelle and detailed by Segers ch11). Plot the four corners side by side.
What you look at first:
- Shape: ideally close to a bell curve (Gaussian), centred on zero.
- Symmetry: bump side (positive) vs rebound side (negative). For mechanical grip, Segers argues the ideal is symmetric – equal time and similar velocities in bump and rebound, keeping tyre load as constant as possible.
- Width: a wide base = lots of high-velocity movement (soft/under-damped or bumpy track); a sharp tall peak = stiff/well-damped.
- Left vs right, front vs rear: big differences between corners point at setup asymmetries, pressure differences or a damper fault. Left vs right compares directly; front vs rear only after correcting for motion ratio (shaft velocity = wheel velocity × MR, see L2).
Key point: the histogram is a tool, not a target. It doesn't show the ideal setup; it shows how the car's suspension is behaving on this track. Its shape changes with damping, springs, ARBs, mass, tyres, pressures and the track itself. Use it for comparison: car A vs car B, run 1 vs run 2, left vs right.
Damper velocity histograms, box plots and run charts: L2 Practitioner explanation
Reading the numbers
Set up the histogram properly (so histograms are comparable):
- Same bin width and same velocity limits for every corner and every run (e.g. 5 mm/s bins, ±300 mm/s).
- Sample pots at ≥ 200 Hz; filter consistently before differentiating.
- Include a zero bin (−2.5…+2.5 mm/s) or sum the two bins adjacent to zero.
- Express as % of samples (time), not counts.
- When zooming into a single corner, start and end at the same damper position – otherwise the extract is biased to bump or rebound.
Metrics per corner (Segers Table 11.4 style)
| Metric | Meaning |
|---|---|
| % LS bump / LS rebound (0…±25 mm/s) | body-motion time per direction |
| % HS bump / HS rebound (> 25 mm/s) | road-input time per direction |
| Avg bump speed / avg rebound speed | magnitude per direction |
| Zero-bin height | relative stiffness of the corner |
Interpretation rules
- More time in LS rebound than LS bump (and lower average rebound speed) → rebound is slow → relatively too much LS rebound (or too little bump). Segers' example: LF 3.5 % more time in rebound → reduce LF rebound or add bump; RR 5.1 % more time in bump → reduce RR bump or add rebound.
- Front vs rear: correct for motion ratio first. Shaft velocity = wheel velocity × MR, so with front MR 0.6 and rear 0.9 the same 35 mm/s wheel motion reads 21 mm/s (LS) at the front and 31.5 mm/s (HS) at the rear. Refer velocities to the wheel (divide by MR) or scale the 25 mm/s boundary by each axle's MR before comparing ends. Track input also differs front to rear (wheelbase filtering, axle loads).
- Front vs rear HS percentages that still differ by several % after that correction → the end with more HS time is under-damped at high speed (Segers: ~6 % more rear HS → add rear HS bump and rebound).
- Zero-bin height differing between corners of a symmetric car (Segers: LF 21 % vs others 14–15 %) → check tyre pressures first, then consider asymmetric damping.
- Average shock speed over a segment equals Δposition / T and must be ≈ 0 over a lap. If not, the segment start and end positions differ, the pot drifted (thermal growth, mounting), or the velocity math channel has a bias (filter/differentiator offset). A gain calibration error cannot cause it.
Aero exception. If you are deliberately using damping to hold attitude (e.g. heavy front rebound to keep the nose down), the histogram will not be symmetric – that's intended. Compare to your own reference shape for that car, not to a textbook Gaussian.
Damper velocity histograms, box plots and run charts: L3 Advanced explanation
Statistics, box plots and run charts
Descriptive statistics (spreadsheet or math channels):
- Median – should be near zero; positive = more samples in bump, negative = more in rebound. First indicator of asymmetry.
- Standard deviation σ – width; large σ = more HS movement. Doesn't capture asymmetry.
- Skewness – asymmetry of the distribution (sign depends on your bump-positive convention; check it with a synthetic test).
- Kurtosis (excess) – peakedness/tail weight. Race-car histograms are usually leptokurtic (> 0): a lot of time near zero plus long tails from bumps/kerbs. Higher kurtosis front vs rear means the front's motion is more concentrated at low speed.
Segers' two-configuration comparison: config 1 has the taller zero bin (14.2 vs 11.5 %), more LS time and the smaller σ (36.5 vs 43.3 mm/s), yet the lower kurtosis (5.7 vs 8.9). Config 2 is flatter and wider overall but has heavier tails relative to its σ. Lesson: kurtosis describes shape (tail weight relative to σ), not peak height.
Box plots (Segers' adaptation): box from 25th to 75th percentile, median line, whiskers at 15th and 85th percentiles (not min/max, which are kerb strikes), plus average bump and rebound speeds. Advantages: objective (no bin choices), four corners comparable at a glance. A bigger box = flatter histogram. Unequal distances from median to the 25th/75th percentiles = asymmetry.
Run charts. Compute per lap the time (not %) each damper spends in LS bump, LS rebound, HS bump, HS rebound (integrate a 1 when velocity is in range, reset per lap). Plot across the whole weekend. Sessions, setup changes, fuel load, tyre degradation and track evolution all show up as steps or trends; it's the fastest way to verify a damper change did what you intended and to spot a damper failing (sudden HS increase on one corner).
What the simple model says (Segers' single-corner simulations): more damping → taller, narrower peak; softer spring → also sharper (the same damper is relatively stronger); more mass → lower peak, wider base. Use it to sanity-check a change: if you added damping and the histogram widened, something else changed (pressures, track, a fault).
Damper velocity histograms, box plots and run charts: L4 Expert explanation
Pitfalls and a more rigorous approach
- Noise inflation: differentiating a pot signal amplifies noise ∝ frequency. An under-filtered velocity channel adds a symmetric "fake" HS population and reduces kurtosis. Use the same filter everywhere and verify with a stationary car (velocity should be ~0 ± 1 mm/s).
- Track content dominates: histograms of the same car at Monza vs Zandvoort differ more than any click change. Only compare within track/conditions; for setup decisions prefer segment histograms (a bumpy braking zone, a kerb set) over full laps.
- Symmetry isn't a law: a damper with rebound > bump under random road input packs down; a perfectly symmetric histogram doesn't guarantee the optimum CPLV. Use histogram symmetry as a starting hypothesis, then confirm with lap time, driver feedback and frequency-domain metrics.
- Velocity ≠ force: two dampers with identical histograms can have very different forces (different curves). Combining velocity data with dyno curves gives a damper force histogram and energy per lap per corner () – a more physical comparison and a check for damper overheating in endurance stints.
- Mode histograms: build histograms of modal velocities (heave, pitch, roll, warp) instead of corners. A roll-velocity histogram isolates transient balance; a heave histogram isolates platform/road input. This removes the cross-talk that makes single-corner histograms ambiguous.
Key formulas
- T
- lap (or segment) duration (s)
- damper velocity samples (mm/s)
- force from dyno curve (N)
Trackside takeaways
Use identical bins/limits/filters for all corners and runs; express as % time.
For mechanical grip aim for symmetric, bell-shaped histograms; aero attitude control legitimately breaks symmetry.
More LS rebound time than LS bump → too much rebound (or too little bump) on that corner.
Zero-bin height differences between corners → check tyre pressures before asymmetric damping.
Box plots (15/25/50/75/85 percentiles) and lap-by-lap run charts make damper behaviour trackable across a weekend.
On your car
Histograms show big HS tails from kerbs; segment the lap (exclude kerb zones) to judge LS behaviour. Compare left/right to catch fuel-load or driver-side asymmetries.
Check yourself
The LF histogram shows 3.5 % more time in low-speed rebound than low-speed bump, with a lower average rebound speed. What does this suggest (aiming for mechanical grip)?
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.3 Shock Speed Ranges
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.4 The Shock Speed Histogram
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.4.3 Statistical Analysis · zero bin, median, σ, skewness, kurtosis, box plots
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.6 Shock Speed Run Charts