Dampers and transient balance: entry and exit
While the body is rolling and pitching, damper forces add to the spring forces and change how load transfer is distributed front to rear. Low-speed bump and rebound, front vs rear, are therefore the tools for entry and exit balance – not for mid-corner.
Dampers and transient balance: entry and exit: L1 Foundation explanation
Dampers as temporary roll stiffness
When the car turns in, the body rolls: the outside wheels go into bump, the inside wheels into rebound. On the axle where the dampers resist that motion more, the load transfer happens faster and larger during the transient – exactly as if that axle had extra roll stiffness for a moment. Once roll stops, damper forces vanish and the springs/bars alone set the balance. This "temporary roll stiffness" picture holds while roll is building; on exit the roll unwinds and the sign flips (below).
So:
- More front damping in roll (front bump on the outside, front rebound on the inside) → more front load transfer during turn-in → more entry understeer, sharper but less front grip at turn-in.
- More rear damping in roll → more rear load transfer during the transient → more rotation / entry oversteer.
Typical starting table (low-speed adjusters, roll-dominated reasoning):
| Phase | Problem | Try |
|---|---|---|
| Entry | understeer | soften front LS bump, or stiffen rear LS rebound |
| Entry | oversteer | stiffen front LS bump, or soften rear LS rebound |
| Exit | understeer | soften rear LS bump, or stiffen front LS rebound* |
| Exit | oversteer (power-on) | stiffen rear LS bump, or soften front LS rebound* |
Why bump at one end and rebound at the other? On entry, braking pitches the car forward: the fronts compress (bump), the rears extend (rebound). On exit, the car squats and the roll unwinds: the rears – above all the inside rear – compress, the outside front extends. The table picks the adjuster on each axle that is actually working in that phase.
Why the exit rows are not the entry rows mirrored. On exit the springs are pushing the body back upright and the dampers resist the unwind: the more-damped axle now takes less load transfer than its springs alone would give. Rear LS bump is the robust exit lever: the inside rear (least loaded, traction-limiting) is compressed by both squat and unwind, so its bump damping pushes it into the road, and squat damping also gets load onto the rear tyres sooner. *Front LS rebound has competing effects: roll unwind and (on aero cars) holding the nose down both reduce exit understeer, but faster rearward pitch transfer slightly adds it. Published damper charts disagree on exit for exactly this reason – verify with data.
Mid-corner: dampers do almost nothing for steady-state balance. If the complaint is mid-corner, use bars, springs, aero, pressures, geometry.
Dampers and transient balance: entry and exit: L2 Practitioner explanation
Doing it with data
1. Identify the phase precisely. Split the corner like Segers' Zolder example: (1) straight-line braking – fronts bump, rears rebound; (2) braking + turn-in – inside front starts to extend, outside front stays compressed, inside rear extends more; (3) mid-corner/throttle pick-up – fronts steady, rears go into bump as the car squats; (4) exit/unwind – outside wheels rebound, inside wheels bump as roll reduces.
2. Find which damper is moving, and how fast. Use LS direction channels (filtered velocity) on the track map. A damper with ~0 velocity in the problem phase cannot be the tool – Segers notes front LS changes have no effect in a steady phase where the fronts aren't moving.
3. Target the least-loaded wheel. The inside wheels have the least load and usually limit the axle. E.g. entry understeer with the inside front in rebound: reduce front LS rebound so the inside front stays on the ground (Segers' suggestion) – this complements the "soften front bump" route.
4. Prefer symmetric changes. Opposite wheels move in opposite directions, so tables seem to suggest asymmetric settings – but asymmetric damping makes left and right corners behave differently. Change left and right together unless the track is strongly one-directional.
Magnitude: LS damper changes are effective for the first ~0.2–0.5 s of a transient – exactly the turn-in and throttle-application phases drivers are most sensitive to. Expect one or two clicks to be clearly felt on stiff, light cars (F3, SF), less on heavy GT cars.
Aero cars – the competing mechanism. On cars with strong ride-height sensitivity, the damping also changes the platform during the transient: more front LS bump holds the front up under braking (less forward aero-balance shift, more stable rear), more front LS rebound holds the nose down on exit (more front downforce, less exit understeer). These aero effects can agree with the mechanical table (front LS rebound on exit) or be opposite in sign to it (rear LS rebound on entry – see L4). Check ride heights in the transient before choosing.
Dampers and transient balance: entry and exit: L3 Advanced explanation
The mechanism, properly
Roll. During roll velocity , each axle's resisting moment is with roll damping (average of bump and rebound coefficients for symmetric motion). The elastic load transfer distribution during the transient is therefore
At turn-in is small and large, so the damping ratio between axles dominates the early distribution; it decays to the stiffness ratio as roll velocity goes to zero. If , the car is more understeery at turn-in than mid-corner, and vice versa. On exit has the opposite sign to (unwind), so the damping term reduces that axle's share: with the same front-biased damping the car is less understeery on exit than in steady state.
Pitch. Longitudinal load transfer between axles () is fixed by statics – dampers cannot change the total axle loads in pitch in steady state. During the transient the pitch-acceleration term , which damping shapes, can briefly shift axle loads by a significant fraction of the steady transfer (illustrative GT3 with an assumed ≈ 1500 kg·m² – take the real value from your sim model: 1° of pitch in 0.15 s → ≈ 0.85 kN, roughly a quarter of ≈ 3.2 kN at 1.5 g, 1300 kg, h 0.45 m, L 2.7 m): with more pitch damping less of the moment goes into pitch acceleration, so the load reaches the tyres sooner. What pitch damping otherwise changes is ride heights (aero), geometry (camber, bump steer, anti effects) and the timing with which pitch combines with roll. That's why the mechanical part of entry/exit tuning is mostly a roll (and diagonal) effect, while pitch damping is a platform effect.
Diagonal (combined) motion. In trail-braking the motion is diagonal: outside front bump + inside rear rebound. Front bump and rear rebound together set the "diagonal damping"; increasing both does little to balance but stiffens the transient overall, while trading one for the other shifts it. Similarly on exit: rear bump vs front rebound.
Wheel-load view. Damper force acts on the tyre: in bump it adds load to that wheel, in rebound it removes load (pulls the wheel up). So stiff front rebound unloads the inside front during turn-in (more understeer). During exit unwind the same adjuster works on the outside front: rebound damping unloads it while bump damping loads the compressing inside front, so front load transfer falls and front grip rises. One adjuster, opposite balance effects on entry and exit – which is why front rebound appears in both rules with opposite signs. At the rear on exit, bump damping loads the inside rear (squat and unwind both compress it) – the traction-limited wheel on a RWD car.
Consistency check with data: compute vs through a turn-in using dyno curves and pot data – if the damping term is less than ~20 % of the elastic term at the moment the driver complains, dampers are not your main lever.
Dampers and transient balance: entry and exit: L4 Expert explanation
Where the simple rules break
- Yaw response vs balance. Faster load transfer at the front also builds front slip-angle response faster (tyre relaxation length, lateral force build-up). A stiffer front LS can feel more responsive at initial turn-in yet produce more understeer 0.2 s later. Drivers may describe both as "better front" or "worse front" depending on what they value; probe with targeted questions (initial response vs mid-entry grip).
- Diff and brakes interplay. Entry balance also depends on diff coast locking, engine braking and brake balance/migration. Damper changes are small compared to diff/brake changes; make sure those are right first.
- Aero non-linearity. On ground-effect cars the platform effect can dominate: e.g. adding rear LS rebound keeps the rear lower in braking (less rake) – may reduce total downforce and rotate balance rearward, giving entry understeer, the opposite of the mechanical rule. Use the aero map with transient ride heights.
- Tyre-dominated roll mode. If roll stiffness is high and the roll mode is tyre-dominated (Segers ch12), damper changes may barely affect roll dynamics; the transient effect then comes mainly through pitch/platform.
- Third dampers (heave) act on axle heave – i.e. the heave/pitch platform – not on roll or warp; corner dampers affect all modes. With heave dampers fitted, use them for the platform objective and corner dampers for the roll objective – the cleanest separation available.
- Simulation: a quasi-static lap sim can't show any of this. Transient vehicle models with roll/pitch dynamics, tyre relaxation and a damper model are needed; validate on a step-steer or a single corner's yaw-rate/steer ratio vs time.
Key formulas
- wheel-referred damping coefficient (N·s/m)
- t
- track (m)
- roll angle (rad)
- roll rate (rad/s)
Trackside takeaways
While roll builds (entry), dampers act like temporary roll stiffness: the more-damped axle takes more load transfer. While roll unwinds (exit) the sign flips: the more-damped axle takes less.
Entry: front LS bump / rear LS rebound. Exit: stiffer rear LS bump is the robust cure for power-on oversteer; front LS rebound has competing roll, pitch and aero effects – verify with data.
Mid-corner (steady state) balance is not a damper problem.
Look at the inside (least-loaded) wheel and at which dampers actually move in the phase of the complaint.
On aero cars, platform effects of damping can oppose the mechanical rules – check transient ride heights.
Keep changes symmetric left/right unless the track is strongly one-directional.
On your car
LS bump front / LS rebound rear are classic GT3 entry tools; combined with bump-stop gaps for high-speed braking stability.
Check yourself
Driver reports understeer only at turn-in (first ~0.3 s), with good mid-corner balance. Which change fits best?
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.1 Shock Absorber Velocity Analysis · roll speed and damper force during corner entry/exit
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.2 Determining in Which Range to Tune the Shock Absorbers · corner phases, Table 11.1, direction channels
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 22 Dampers
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 6 Simplified Transient Stability and Control