Kerb riding and high-speed damping control
Kerbs and big bumps drive shaft velocities to several hundred mm/s. High-speed bump lets the wheel climb without launching the car, high-speed rebound returns it to the ground without bouncing, and the whole package (springs, bump stops, ARBs, ride height) decides whether the car can use kerbs.
Kerb riding and high-speed damping control: L1 Foundation explanation
What happens on a kerb
Hitting a kerb pushes one or two wheels up in a few hundredths of a second. Shaft velocities of 200–600 mm/s (sausage kerbs and high kerbs up to ~1 m/s) are typical – far into the high-speed range.
- High-speed bump (compression) decides how much of that impact goes into the chassis. Too stiff → the force spike lifts and launches the car, the other tyres lose load, the driver feels a "kick". Too soft → the suspension uses all its travel and hits the bump stops hard (which is even stiffer).
- High-speed rebound (extension) decides how quickly the wheel comes back down after the kerb. Too stiff → the wheel "hangs" in the air, the tyre loses contact, and repeated kerbs pack the car down. Too soft → the wheel springs back and bounces, unsettling the car.
A car that "rides kerbs well" lets the driver straight-line chicanes and use exit kerbs without losing the rear – often worth several tenths per lap at tracks like Monza, Zandvoort, Sebring, Bathurst or street circuits.
It's never only dampers. Single-wheel stiffness (corner spring + about half the ARB rate + bump stops), ride height and bump-stop gap all decide kerb behaviour. With the ARB rate quoted as the usual per-wheel rate in pure roll, a single-wheel kerb strike sees half of it (the bar twists half as much as when both wheels move opposite) – so a stiff ARB still transmits a large share into the strike.
Kerb riding and high-speed damping control: L2 Practitioner explanation
Diagnosing and tuning kerb behaviour
Data to look at
- Damper velocity peaks at each kerb (bump and rebound) and the time to settle (number of oscillations after the strike).
- Damper position: did it reach the bump-stop gap? Hit full droop on the way back?
- Vertical acceleration of chassis (and hub, if fitted) – spikes of 3–6 g on the chassis are common, hub much higher.
- Steering and yaw-rate response just after the kerb: driver corrections reveal instability.
- Lap time segment: compare laps with and without kerb use.
Typical moves
| Symptom | Likely cause | Try |
|---|---|---|
| Car launched/"kicked" by kerb | HS bump too stiff or blow-off too high, stop engaged | softer HS bump, more bump-stop gap, softer ARB |
| Wheel hangs, rear steps out after exit kerb | HS rebound too stiff / packing down | less HS rebound |
| Car bounces after kerb, takes several cycles to settle | HS rebound too soft | more HS rebound |
| Floor/plank strikes on kerbs | ride height / heave too soft or packers | ride height +, packers, stiffer heave |
Packing down / jacking. Over a series of bumps or a "sawtooth" kerb, a damper with much more rebound than bump at high speed can't extend fully between hits: the car sinks lower with each hit (packs down), losing travel and hitting stops. The opposite (bump ≫ rebound) jacks the car up. Look at the mean damper position across a kerb sequence.
Dedicated kerb setup decisions are a trade: softer HS bump and more gap for kerbs usually costs a little platform on smooth high-speed sections. Some dampers offer a hydraulic bump stop or blow-off valve to keep LS/medium-speed control while capping kerb forces.
Kerb riding and high-speed damping control: L3 Advanced explanation
The physics of a kerb strike
A kerb is a displacement input with a very high velocity: a 40 mm step kerb at 150 km/h taken over ~0.3 m length rises in ~7 ms – a velocity input far above any body frequency. The damper force for a linear HS slope is ; at 500 mm/s with = 7 N·s/mm (damper) that's 3.5 kN – comparable to the static corner load. The impulse transmitted to the body is roughly – so for a given kerb, HS bump force × duration sets body disturbance. Blow-off (knee) caps , limiting the impulse.
Wheel dynamics after the strike. The unsprung mass, launched upward, is restored by the spring + tyre and damped by HS rebound. With wheel ζ ≈ 0.3–0.5 and ≈ 15 Hz, the wheel settles in ~1–2 cycles (~70–130 ms). Too little ζ → visible ringing at in the damper-position trace and tyre-load spikes; too much rebound → the wheel can't follow the falling side of the kerb, contact is lost (zero tyre load) for tens of ms – lateral grip at that corner disappears, which is the "rear steps out after the kerb" feeling.
Tyre load during kerbs can be estimated with hub accelerometers or from pushrod load plus unsprung inertia (after Segers §12.8, Eq. 12.35, which uses dynamic components only; for absolute load add ): , upward positive, with the total spring + damper + bump-stop force referred to the wheel (plus the vertical component of link forces under braking/traction). If is the raw accelerometer reading (≈ +1 g at rest), it already contains . Contact-patch load reaching zero is the objective failure criterion.
Kerb compliance budget
- Single-wheel rate (corner spring + ½ ARB per-wheel roll rate + ¼ axle heave rate) – lower = less force spike.
- HS bump slope and blow-off – lower = less impulse.
- Bump-stop gap – enough to avoid stop contact on the kerb.
- HS rebound – enough to avoid ringing, not so much to pack down.
Packing analytically. Under periodic input of amplitude and frequency , an asymmetric damper (bump , rebound ) produces a mean force of (bilinear model, velocity amplitude ) that must be balanced by a spring offset: . Fast, large inputs (kerb sequences) and soft springs maximise packing.
Kerb riding and high-speed damping control: L4 Expert explanation
Advanced considerations
- Cavitation and hysteresis at high velocity: insufficient gas pressure lets the rebound chamber cavitate after a hard bump stroke → rebound force arrives late, wheel overshoots. Check dyno hysteresis loops at 300–500 mm/s.
- Kerb-strike modelling in simulation requires the tyre's enveloping behaviour (the tyre "swallows" short kerbs – effective input is filtered by contact-patch length), damper non-linearity and bump-stop curves. Linear quarter-car models overestimate peak forces on sharp kerbs.
- Chassis torsion absorbs part of a single-wheel strike on less stiff chassis (GT4/TCR) and redistributes load diagonally (warp). Warp is not resisted by third (heave) springs, but it is resisted by corner springs and ARBs (front and rear roll stiffness acting roughly in series, with the body free to roll), by the tyres and by chassis torsion. A softer chassis adds compliance in series with the suspension: it lowers warp stiffness, so less of a single-wheel strike is passed diagonally to the opposite corners, at the cost of less precise load distribution.
- Driver-specific: some drivers attack kerbs, others avoid them. Analyse kerb usage per driver before changing the car; in multi-driver endurance cars, choose a setup that is robust to kerb use rather than optimal for one style.
- Regulatory/track factors: track limits enforcement and kerb shapes (sausages, negative kerbs) change from event to event; a kerb setup is circuit- and even session-specific (wet: less kerb use).
Key formulas
- force at knee/blow-off (N)
- high-speed slope (N·s/mm)
- knee velocity (mm/s)
- spring + damper + bump-stop force on the hub, referred to the wheel, plus vertical link-force components (N)
- unsprung mass (kg)
- hub vertical acceleration, up positive, excluding gravity (m/s²); a raw accelerometer reading already includes g
- rebound / bump coefficients
- X
- input amplitude
- k
- spring rate
Trackside takeaways
Kerbs produce 200–600+ mm/s shaft speeds: HS bump decides launch, HS rebound decides return.
Rebound ≫ bump at HS over repeated bumps → car packs down; bump ≫ rebound → jacks up.
Kerb compliance = single-wheel rate (spring + ½ ARB + ¼ heave) + HS damping + bump-stop gap.
The failure criterion is contact-patch load reaching zero after the strike.
Analyse kerb usage per driver and per session before making a kerb setup change.
On your car
Kerb riding is crucial at Monza, Zandvoort, Spa (Bus Stop) and Bathurst; softer HS bump, more front bump-stop gap and softer ARBs are the common package. Watch rear stability on exit kerbs.
Check yourself
Over a sequence of sawtooth kerbs, the mean damper position drifts toward bump and the car hits its bump stops. Which damper characteristic causes this?
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.3 Shock Speed Ranges · kerbs produce very high shock speeds
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.8 Frequency Analysis from Sensor Data · contact patch load from hub dynamics
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 22 Dampers