Frequency-domain suspension analysis & modal decomposition
Transfer functions, power spectral densities and modal decomposition (heave, pitch, roll, warp) characterise the suspension independent of a particular bump. They reveal body and wheel-hop resonances, quantify grip (tyre load variation) vs platform (body motion), and are the basis of 4/7-post rig and on-track damper optimisation.
Frequency-domain suspension analysis & modal decomposition: L1 Foundation explanation
Why look at frequencies?
Any road input – bumps, ripples, kerbs – can be broken down into many sine waves of different frequencies (Fourier). A suspension responds very differently to each:
- Below the body frequency (< ~2 Hz): the body follows the road (long undulations, crests).
- Around the body frequency (~2–5 Hz on race cars): the body resonates – it moves more than the road input unless damped.
- Between body and wheel-hop (~5–12 Hz): the body is isolated; the wheel follows the road.
- Around wheel hop (~12–20 Hz): the wheel resonates on the tyre – tyre load fluctuates strongly, grip suffers.
- Above: the tyre itself absorbs input.
So a race car has two key resonances per corner: the body mode (platform) and the wheel-hop mode (grip). Damping is mainly about controlling these two peaks.
The road input frequency depends on car speed: a surface wavelength λ excites . At 250 km/h (69 m/s), a 20 m undulation excites 3.5 Hz – right on the body mode; a 4 m ripple excites 17 Hz – wheel hop. The same track bump can be harmless at 100 km/h and a problem at 250 km/h.
Modes of the whole car. Four corner motions combine into four modes: heave (all together), pitch (front vs rear), roll (left vs right) and warp (diagonals opposite). Each has its own stiffness, inertia and damping – and each matters differently for aero and grip.
Frequency-domain suspension analysis & modal decomposition: L2 Practitioner explanation
Practical frequency analysis with car data
PSD of damper or ride-height signals. Export damper positions (or laser ride heights) for a stable section of the lap (or the whole lap), at ≥ 200 Hz (500 Hz better for wheel hop). Compute the power spectral density with Welch's method (segments of 2–4 s, Hann window, 50 % overlap). Plot on log axes. Look for:
- Peak at 2–5 Hz = body mode; its height relative to the low-frequency level tells you how well damped it is.
- Peak at 12–20 Hz = wheel hop; tall/narrow = under-damped wheel.
- Narrow spikes at fixed frequency across speeds = mechanical (driveline, engine order) – not suspension.
- Peaks that move with speed = road wavelength excitation ().
Segment by speed (e.g. 150–200 and 200–250 km/h) so the road input spectrum is comparable between runs.
Modal channels (Segers ch12, displacements positive in bump): PSDs of and describe the aero platform; describes roll dynamics; (warp) is pure road input (track twist, kerbs) and produces diagonal load changes without body motion.
Using it
- Compare runs before/after a damper change: did the body peak drop? did the wheel-hop peak drop or grow?
- On aero cars, minimise heave/pitch PSD energy in 1–6 Hz at high speed (platform).
- On mechanical cars, minimise wheel-hop peaks and 2–10 Hz tyre-load content (grip).
Four-post rig: shakes each wheel with sine sweeps or track replays and measures contact-patch load directly – the most controlled place to measure tyre load variation (on track you need wheel force transducers, or pushrod load plus hub acceleration – see L4). Limits: non-rolling tyre, no real aero (7-post adds aero actuators), car on rig may differ from car on track.
Frequency-domain suspension analysis & modal decomposition: L3 Advanced explanation
Transfer functions and the quarter car
Single-DOF transmissibility (body displacement / road displacement) for frequency ratio :
at low , peak near (≈ for small ζ; ≈1.4–1.5 at ζ = 0.5, ≈1.2–1.3 at ζ = 0.7), crossover at regardless of ζ, and isolation above. Note the trade-off: more damping lowers the resonance but raises transmissibility above – Segers fig. 12.12 shows over-damped settings increasing response in the 1–10 Hz band, hurting grip and comfort.
Quarter car (sprung , unsprung , , , ) gives three useful FRFs (Segers fig. 12.10): road → body displacement (platform/stability), road → tyre deflection (∝ contact-patch load variation, i.e. grip), road → suspension travel. Optimising damping on the peak of each gives different optima: grip prefers less damping than body control. Heavier unsprung mass raises the tyre-load FRF around wheel hop – the reason regulations and engineers chase low unsprung mass.
Modal stiffness matrix (Segers §12.5): with front/rear corner rates and ARB rates, the modal elasticities are e.g. heave , roll from springs and ARBs, and off-diagonal terms and coupling heave–pitch and roll–warp. The roll–warp coupling term is what sets mechanical balance (LLTD): front/rear roll stiffness difference shows up as warp coupling. Tyres and chassis enter in series, softening especially warp.
Effective modal masses. Race cars concentrate mass centrally, so the equivalent mass per wheel in roll is only ~20–40 % and in pitch ~60–80 % of the quarter mass (Segers). Roll therefore has high frequency, high stiffness and low inertia; with the tyre comparable in stiffness to the suspension in roll, the roll mode gets "trapped" with the tyre's low damping – race-car roll transfer functions show poorly damped peaks that dampers can only partly control.
Frequency-domain suspension analysis & modal decomposition: L4 Expert explanation
FRFs from on-track data and their limits
Building FRFs from car sensors (Segers §12.8): with body vertical acceleration , suspension displacement (→ suspension acceleration), wheel loads (pushrod) and known , :
- Hub acceleration (or measured with an upright accelerometer).
- Contact-patch load (Segers' Eq. 12.35 omits because it works with dynamic components; the term gives absolute load. Up positive; = total spring + damper + bump-stop force at the wheel; a raw accelerometer reading already contains ); contact-patch (road) acceleration assuming a linear tyre spring.
- FRFs as ratios of spectra: body/contact-patch and hub/contact-patch. Use cross-spectral estimators () and check coherence – low coherence (< 0.7) means nonlinearity, noise or uncorrelated inputs, and the FRF there is unreliable.
Practical requirements: ≥ 500 Hz for hub content; anti-alias filtering; position sensor resolution limits high-frequency acceleration derived by double differentiation (Segers notes this impairs high-frequency data); speed-segmented averaging; correction for anti-geometry load paths in braking.
Non-linearity. Dampers are neither linear nor symmetric, bump stops and packers are piecewise, friction locks the suspension at small amplitudes, aero stiffness varies with speed and ride height. FRFs are therefore amplitude- and speed-dependent – quote them with the operating condition. Asymmetric damping additionally produces mean offsets (jacking) that no linear FRF shows.
Aero-coupled dynamics. At speed, and add (usually destabilising) stiffness and, through flow lag, effective damping to heave and pitch. A 7-post rig with aero actuators or on-track FRFs are the only way to see the real platform modes; porpoising appears as a speed-dependent, lightly damped (or growing) heave/pitch peak in the 3–8 Hz region.
From analysis to decision. Define a cost: e.g. weighted sum of contact-patch load RMS (grip, per axle, weighted by aero balance/tyre load sensitivity) and ride-height RMS at the aero reference points (platform). Optimise damper clicks on a rig or a validated vertical-dynamics model driven by measured road profiles, then confirm on track with PSD/histogram metrics and the driver. That closes the loop between Segers ch11 (time/statistical) and ch12 (frequency) methods.
Key formulas
- V
- car speed (m/s)
- road wavelength (m)
- H, P, R, W
- heave, pitch, roll, warp
- z
- corner wheel displacement
- total suspension force on the hub, referred to the wheel (N)
- hub vertical acceleration excluding gravity, up positive (m/s²)
- cross-spectral density
- coherence (0–1)
Trackside takeaways
Two key resonances per corner: body (~2–5 Hz, platform) and wheel hop (~12–20 Hz, grip).
Road wavelength excites f = V/λ – the same bump matters differently at different speeds.
More damping lowers the resonance peak but raises transmission above √2·f_n: grip optimum < platform optimum.
Modal channels (heave, pitch, roll, warp) separate platform, balance and road-twist effects.
On-track FRFs need high sampling, cross-spectral estimators and coherence checks; results are amplitude- and speed-dependent.
On your car
Body ~3 Hz, wheel hop ~14–17 Hz. Ride-height PSD at high speed shows bump-stop-stiffened body peaks; good for checking platform at Spa/Monza.
Check yourself
At 216 km/h (60 m/s), which road wavelength excites a 3 Hz body mode?
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.1 Introducing Frequency Analysis
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.3 Theoretical Analysis · transfer functions, quarter-car, unsprung mass and damping effects
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.4 Suspension Optimization Using Frequency Analysis
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.5 Modal Analysis
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.8 Frequency Analysis from Sensor Data
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 16 Ride and Roll Rates
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 22 Dampers