Ride frequency and how to choose it
Ride frequency normalises stiffness by sprung mass so cars of different weight can be compared. Choosing it is a trade between mechanical grip over bumps and aero platform control, with the front/rear ratio shaping pitch behaviour.
Ride frequency and how to choose it: L1 Foundation explanation
Natural frequency of the body on its springs
Treat one corner as the sprung mass (that corner's share of body, driver, fuel – excluding wheels, uprights, brakes and roughly half the links) sitting on the ride rate . It oscillates at
with in N/m and in kg. Frequency is a better language than spring rate because it is independent of the car's mass: "3 Hz" means the same stiffness relative to the mass on a 1300 kg GT3 and a 600 kg F4.
A useful intuition: the static deflection under 1 g is . At 1 Hz (road car) that is ~250 mm; at 3 Hz ~28 mm; at 5 Hz ~10 mm. Race cars are stiff because they cannot afford the travel – geometry, aero and ground clearance all need a controlled platform.
Indicative ride frequencies (mechanical corner rates incl. tyre)
| Category | Approx. ride frequency |
|---|---|
| Road car | 1.0–1.5 Hz |
| GT4 | 2.0–2.6 Hz |
| One-make cup / TCR | 2.5–3.2 Hz |
| GT3 | 2.8–3.6 Hz (plus bump stops at speed) |
| F4 | 3–4 Hz |
| LMP2 / Formula Regional | 3.5–4.5 Hz |
| Hypercar, F3/F2, SF, IndyCar road course (heave) | 4–6 Hz |
These are typical ranges, not rules – read your car's data.
Rule of thumb: more downforce → higher frequency, because a stiffer platform is needed to hold the ride height the aero was designed for.
Ride frequency and how to choose it: L2 Practitioner explanation
Working with frequency trackside
From frequency to spring. Choose , compute the required ride rate , back out the wheel rate from the series formula , then the spring . The calculator does this chain. Get from corner weights minus estimated unsprung mass (GT3 ~45–60 kg per corner, formula cars ~25–40 kg).
Example – GT3 rear corner: corner weight 360 kg, unsprung 55 kg → = 305 kg. Target 3.2 Hz → = 305·(2π·3.2)² ≈ 123 N/mm. Tyre 360 N/mm → ≈ 187 N/mm. MR 0.8 → spring ≈ 292 N/mm.
Front/rear frequency ratio. On road cars, Olley's "flat ride" principle puts the rear frequency 10–20 % above the front so that after a bump the rear (which hits it later) catches up with the front and the body bounces rather than pitches. The delay is : 2.7 m at 100 km/h is 97 ms, a big fraction of a 1 Hz period. At 250 km/h it is 39 ms vs a ~300 ms period for a 3.3 Hz race car, so the flat-ride argument is weak on a race car. Race engineers instead choose the ratio for:
- Aero platform: front ride height is usually the most sensitive aero parameter (splitter/front floor), so high-downforce cars often run the front stiffer in heave than the rear.
- Traction: a softer rear (lower frequency) helps a RWD car put power down over bumps.
- Balance: front/rear heave stiffness changes the mechanical balance only indirectly (via roll stiffness on cars without third springs, and via aero platform).
Typical front/rear ratios lie within ±15 % of 1.0.
Pitfalls
- Using wheel rate instead of ride rate (tyre forgotten) over-estimates frequency by a factor : ~10–25 % on GT cars, 40 %+ on stiff aero cars where .
- On cars with ARBs and no third spring, raising corner springs also raises roll stiffness – check LLTD after any frequency change.
- On GT3, quoted spring frequencies ignore the bump stop: at high speed the effective frequency can be 30–60 % higher.
Ride frequency and how to choose it: L3 Advanced explanation
Choosing the frequency – the real trade-off
The ride frequency is the outcome of three competing demands:
- Mechanical grip wants low contact-patch load variation. On a bumpy surface, softer suspension (lower ) reduces tyre load fluctuation in the 2–10 Hz range – up to a point, after which body motion and travel limits dominate.
- Aero platform wants small ride-height and pitch variation. The required heave stiffness follows directly from allowable ride-height change: . E.g. a GT3 with ~3 kN extra rear downforce at Vmax on an axle heave ride rate of 2·110 = 220 N/mm drops ~14 mm – usually too much without bump stops, which is exactly why GT3s use them.
- Geometry and travel: camber change, bump steer, damper travel and skid-block/plank wear limit total motion.
The optimum therefore scales with downforce: low-downforce cars sit near 2–3 Hz where mechanical grip dominates; high-downforce cars move to 4–6 Hz in heave and accept a mechanical-grip penalty because the aero gain is larger.
Frequency vs damping. Body frequency and damping must be chosen together. Doubling stiffness raises by √2 and lowers the damping ratio by 1/√2 for the same damper. A frequency change without a damper adjustment is a combined change.
Heave vs pitch vs roll frequency. The single-corner frequency is a simplification. The body has separate modes:
- Heave – all four corners together.
- Pitch – depends on the pitch inertia and . The dynamic index is ~1 on many road cars (front and rear then act independently, which is Olley's assumption) but often 0.6–0.8 on race cars where mass is centralised – the pitch mode is then higher than the heave mode and the corner-frequency picture under-predicts pitch stiffness. Segers reports equivalent pitch masses of 60–80 % of vehicle mass on race cars.
- Roll – roll inertia is small and roll stiffness (with bars) large, so roll "frequencies" are much higher; equivalent roll masses are only ~20–40 % of the car (Segers ch12).
Measuring. Verify on track: the PSD of ride-height or damper-position signals shows the body mode as a peak (see the frequency-domain lesson); a 4-post rig gives it directly.
Ride frequency and how to choose it: L4 Expert explanation
Limits of the frequency concept
- Amplitude dependence. Real cars have friction, progressive bump stops, MR progression and aero stiffness. The "frequency" at 2 mm amplitude in a slow corner differs from that at 15 mm at Vmax. Quote frequency together with the operating point (speed, ride height, bump-stop engagement).
- Speed dependence. With ground-effect aero, net heave stiffness = , and is normally negative (more downforce as the car drops). The aero term alone therefore lowers the effective frequency with speed; near the stall region the aero response can also remove damping – porpoising is the extreme case. On cars running onto progressive stops, packers or rising-rate rockers the mechanical rise usually dominates (the GT3 case in the practitioner section), so the net frequency at speed can be higher or lower – measure it rather than assume.
- Coupled modes. With a cross-coupled stiffness (), heave and pitch couple; the measured peaks are mixtures. Modal decomposition (heave = mean of four, pitch = front − rear, etc.) of the measured motion gives cleaner estimates than single-corner signals.
- Tyre-dominated regime. Once , ride frequency asymptotes to (≈ 6–7 Hz for a formula-car corner with ~300 N/mm tyres and 150–190 kg sprung mass; lower for a heavier prototype corner). Extra spring then buys platform only through reduced suspension travel, while the tyre-dominated mode becomes poorly damped. That ceiling is why ground-effect cars bottom out on stiffness and move to ride-height control via packers, heave stops and aero design rather than ever-stiffer springs.
- Frequency ratio as a balance tool is at best second order on race cars; changes in front/rear heave stiffness act on balance mostly through aero platform (front ride-height sensitivity) and through the roll stiffness of corner springs. Attribute a balance change to "frequency ratio" only after ruling those out.
Key formulas
- f
- ride frequency (Hz)
- ride rate (N/m)
- sprung corner mass (kg)
- tyre rate (N/m)
- g
- 9.81 m/s²
- pitch radius of gyration (m)
- a, b
- CG to front / rear axle (m)
Ride frequency
Combine wheel rate and tyre rate into ride rate and natural frequency for both axles, compared with typical ranges per car category.
Front
Rear
Typical GT / GT3: 2–3 Hz. Moderate downforce; platform control vs. kerb compliance.
Trackside takeaways
f = (1/2π)·√(K_ride / m_sprung); always include the tyre.
Typical: GT4 ~2–2.6 Hz, GT3 ~2.8–3.6 Hz, LMP2 ~3.5–4.5 Hz, F3/F2/SF/IndyCar heave ~4–6 Hz.
Frequency rises with downforce because the platform must hold ride height: Δh = ΔF_aero / K_heave.
Flat-ride (rear > front) matters less at race speeds; race cars set the ratio for aero platform and traction.
Stiffer springs with the same dampers = less damping ratio. Change both consciously.
On your car
Mechanical ride frequencies ~2.8–3.6 Hz, but bump stops carry much of the aero load at speed, so effective high-speed frequency is far higher. Spring choice is often for low-speed grip and kerbs; bump-stop gap/rate for platform.
Check yourself
F3-type front corner: corner weight 170 kg, of which 35 kg unsprung. Spring 300 N/mm at MR 0.9 (spring/wheel travel), tyre rate 280 N/mm. What is the ride frequency?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 16 Ride and Roll Rates
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 21 Suspension Springs
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.6 Modal Frequency Issues · wheel-equivalent masses for roll (≈20–40 %) and pitch (≈60–80 %) on race cars