Wheel rate, tyre rate & ride rate (springs in series)
The spring on the damper is not the stiffness the tyre sees. Motion ratio turns spring rate into wheel rate, and the tyre acts as a second spring in series, giving the ride rate that actually sets body frequency.
Wheel rate, tyre rate & ride rate (springs in series): L1 Foundation explanation
Three stiffnesses, one corner
A race car corner has (at least) two springs between the body and the track:
- The suspension spring, mounted on the damper, usually driven through a pushrod/rocker or directly by the wishbone. Its catalogue rate (N/mm) is what you write on the setup sheet.
- The tyre, which is itself a stiff air spring with a vertical rate of roughly 250–450 N/mm for a racing slick.
The spring does not move as much as the wheel. The motion ratio = spring travel / wheel travel (typically 0.6–1.0). Because the lever reduces both the travel and the force seen at the wheel, the wheel rate scales with the square:
A 200 N/mm spring at is only 128 N/mm at the wheel.
The suspension and tyre are in series – the same load passes through both, and their deflections add. Series springs combine like resistors in parallel:
is the ride rate: the stiffness between the sprung mass and the road. It is always lower than the softer of the two.
Typical numbers
GT3 front: = 200 N/mm, MR = 0.9 → = 162 N/mm. Tyre 360 N/mm → ≈ 112 N/mm. The tyre takes about a third of the ride deflection. On formula cars with stiffer springs the tyre takes more than half.
Why you care: every frequency, roll-stiffness and platform calculation you do later must use the correct rate – using spring rate instead of ride rate is the most common first-season mistake.
Wheel rate, tyre rate & ride rate (springs in series): L2 Practitioner explanation
Getting the rates right trackside
Motion ratio comes from the kinematics model or a simple measurement: jack the wheel (spring removed or replaced by a solid link), log wheel travel vs damper travel at 5 mm steps through the working range. The slope is MR. If the damper is inclined to the wheel's path, the cosine of that angle is already contained in a measured MR – don't apply it twice. Remember MR is generally not constant: rocker geometry gives a rising or falling rate over travel; use the value at the dynamic ride height, not at full droop.
Tyre rate depends on pressure (rises roughly linearly – a few % per 0.1 bar), construction, load, camber, temperature and speed. Typical vertical rates:
| Tyre | Approx. |
|---|---|
| F4 slick | 200–260 N/mm |
| GT3 / LMP2 slick | 300–420 N/mm |
| F2 / SF / IndyCar slick | 300–400 N/mm |
Use the manufacturer's data (at hot pressure) if available; rig data or a data-logging method otherwise: wheel load from pushrod load cells (Segers §10.6) plotted against tyre deflection, taken as laser ride height minus the pot-derived ride height (Segers §13.4.2).
Practical consequences
- Doubling the spring does not double the ride rate. F3 example: = 250 → 500 N/mm with = 300 N/mm changes from 136 → 188 N/mm, only +38 %.
- A tyre pressure change is a stiffness change. In ride, a 10 % tyre-rate change is worth about of wheel rate: ≈4–5 % on a GT3 (), 10–20 % on a stiff aero car. Segers' roll-ratio example (one car, one metric) needed +25 % rear wheel rate to undo a 10 % rear tyre-rate change. When you change compound/construction or run pressures 0.2 bar off-target, your spring setup has effectively changed.
- When comparing to another team's sheet, compare wheel rates, not spring rates – the motion ratios may differ.
- Bump rubbers, heave springs and ARBs add in parallel with the corner spring before the tyre is put in series.
Pitfall: Segers and several data tools define motion ratio the other way round (wheel/spring > 1), giving . Always check which convention a sheet uses.
Wheel rate, tyre rate & ride rate (springs in series): L3 Advanced explanation
Parallel and series networks, and what really sets the rate
Build the corner as a network: in parallel at the wheel, the corner spring , the bump-stop rate when engaged, a share of the ARB (roll only) and of the heave element (heave only). In series with that, the tyre and also the compliance of the suspension itself – wishbone bending, rocker and pushrod stretch, bearing slop, upright and chassis pick-up flex. On many cars the structure is "only" 3000–10000 N/mm, which still removes several % of a stiff wheel rate. Rig-measured wheel rates are therefore 3–10 % below the calculated on stiffly sprung formula cars.
Because series compliances add,
the softest element dominates. On a high-downforce car with wheel rates of 400–600 N/mm, the tyre is the softest element in heave, so tyre pressure, construction and even tyre temperature drive the body frequency more than a 20 % spring change. That is why aero platform work starts from a good tyre model.
Non-constant motion ratio. With a rocker, varies with wheel travel ; the instantaneous wheel rate is
The second term (spring force times rate of change of MR) is often forgotten – with a large preload or a strongly rising rocker it can be 10–20 % of the total and is how "progressive" rockers stiffen the car as aero load compresses it.
Tyre rate is not a constant either. It rises with pressure and, mildly, with deflection/load (the load–deflection curve of a slick is near-linear and slightly progressive); the rolling tyre differs from a static pad measurement, and warm tyres are softer than cold ones at the same pressure. Expect ±10 % across a stint as pressures build. Using static cold numbers can mis-predict body frequency by 5 %.
Measuring. Compare the theoretical ride rate to the rate inferred on track: ride-height laser (body to ground) vs pushrod load (or modelled load from damper position × wheel rate) gives the total; pot displacement gives the suspension share; the difference is tyre (+ structure) deflection.
Wheel rate, tyre rate & ride rate (springs in series): L4 Expert explanation
Edge cases a simulation engineer must handle
Single-wheel vs heave vs roll rate. "Wheel rate" is mode-dependent once an ARB or third element is fitted. For a single-wheel input the ARB contributes about half its roll-mode wheel rate (the opposite wheel stays put, so the bar twists half as much) and a heave element contributes about a quarter of its axle heave rate. Kerb compliance therefore depends strongly on how much of the axle stiffness you carry in ARB/third spring vs corner springs.
Tyre damping and hysteresis. The tyre is a spring with very low damping (ζ ≈ 0.03–0.05 on its own). Every mode in which the tyre is the dominant compliance (wheel hop, the race-car roll mode, the heave mode of very stiff aero cars) is poorly damped by the tyre and must be controlled by the damper through the suspension – which becomes ineffective when the suspension is much stiffer than the tyre. This is the fundamental limit on how stiff you can spring a car: past a wheel-rate/tyre-rate ratio of roughly 1:1 the damper "sees" less and less of the motion and contact patch load variation rises.
Aero stiffness. Downforce depends on ride height. Over most of the map downforce rises as the car gets lower (), so the aero "spring" is destabilising: the net heave stiffness is , i.e. less than the mechanical rate. Near the ground-effect stall the slope changes abruptly. On F2/SF23/hypercar platforms the aero term can be tens of N/mm per axle at speed – enough to shift heave frequency by 5–10 % – and around the stall the downforce–height curve plus its time lag can feed energy into the heave mode (effectively negative damping): porpoising.
Series stiffness in roll with chassis torsion is handled in the roll-stiffness lesson; the same rule (series compliances add) applies, and a torsionally soft chassis caps the roll-stiffness distribution range you can achieve with bars.
Key formulas
- wheel rate (N/mm)
- spring rate (N/mm)
- MR
- motion ratio, spring travel / wheel travel (–)
- ride rate (N/mm)
- tyre vertical rate (N/mm)
- structural compliance of links, rocker, upright, pick-ups (N/mm)
- spring force (N)
- z
- wheel travel (mm)
Trackside takeaways
Wheel rate = spring rate × MR² (with MR = spring/wheel travel). Check which MR convention the sheet uses.
Tyre and suspension are in series: ride rate is always below both. Use ride rate for frequencies.
Tyre rate ~250–450 N/mm on slicks; on stiff aero cars the tyre is the softest spring in heave.
A tyre pressure / construction change is a stiffness change: in ride, 10 % tyre rate ≈ 10 %·(K_w/K_t) of wheel rate (≈4–5 % on a GT3, 10–20 % on a stiff aero car); Segers' roll-ratio example needed +25 % wheel rate.
Compare setups across cars in wheel rate, never spring rate.
On your car
Coil-over corner springs, MR ~0.8–1.0 at the front, often lower at the rear. Typical wheel rates ~120–250 N/mm; tyre ~320–400 N/mm, so the tyre takes 30–45 % of ride deflection. Bump stops add a large parallel rate at speed.
Check yourself
A 180 N/mm spring is mounted with a motion ratio (spring travel / wheel travel) of 0.75. What is the wheel rate?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 16 Ride and Roll Rates
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 21 Suspension Springs
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 23 Compliances
- Segers – Analysis Techniques for Racecar Data Acquisition — §9.3 Using Roll Gradients as a Setup Tool · wheel rate from spring rate and motion ratio (inverse MR convention)
- Segers – Analysis Techniques for Racecar Data Acquisition — §9.4 Front to Rear Roll Angle Ratio · worked example: +10 % rear tyre rate needs ≈ +25 % rear wheel rate to restore the roll ratio
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.6 Measuring Wheel Loads with Suspension Load Cells
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.7 Tire Spring Rates · tyre springs act in series with the suspension springs
- Segers – Analysis Techniques for Racecar Data Acquisition — §13.4 Ride Height Measurement · tyre deflection = laser ride height minus suspension ride height