Learn / Springs, Anti-roll Bars & Heave / Heave / third springs: decoupling heave from roll
L2 · Practitioner

Heave / third springs: decoupling heave from roll

A third (heave) element acts only when both wheels of an axle move together. It lets aero cars hold ride height under downforce with high heave stiffness while roll stiffness and single-wheel compliance are tuned separately.

Heave / third springs: decoupling heave from roll: L1 Foundation explanation

Why a third spring?

With only corner springs and ARBs, an axle has two stiffnesses you can tune:

  • Heave (both wheels together): set by corner springs only.
  • Roll (wheels opposite): corner springs + ARB.

An aero car needs very high heave stiffness – downforce of several kN would otherwise squash it onto the ground and wreck the aero map – but does not want correspondingly high stiffness for single-wheel bumps and kerbs. Stiff corner springs give both, plus roll stiffness you may not want.

A third spring (heave spring) is mounted between the two rockers of an axle (or on a separate rocker driven by both pushrods) so that it compresses only when both wheels rise together. In roll, one rocker moves up and the other down – the third element doesn't move.

So the stiffness "menu" becomes:

ModeCorner springsARBThird spring
Heave✓–✓
Roll✓✓–
Single-wheel bump✓~½~¼

The car can then be stiff in heave (platform), stiff-ish in roll (aero attitude, balance via bars), yet relatively compliant to single-wheel inputs.

Where you find them: LMP2, hypercars, F3/F2, Super Formula, IndyCar, and many other prototypes. GT3/GT4/TCR/one-make cups use corner springs + ARBs + bump stops instead.

Key formulas

Axle heave rate with third element
Kheave=2Kw+K3 MR32K_{heave} = 2K_w + K_3\,\mathrm{MR}_3^2
K3K_3
third spring rate (N/mm)
MR3MR_3
third-element travel per unit axle heave
Axle roll stiffness (third element absent)
Kϕ=(Kw+Karb) t22K_\phi = (K_w + K_{arb})\,\frac{t^2}{2}
KarbK_{arb}
ARB rate per wheel in roll (N/m)
Single-wheel rate (approx.)
Ksingle≈Kw+12Karb+14K3MR32K_{single} \approx K_w + \tfrac{1}{2}K_{arb} + \tfrac{1}{4}K_3\mathrm{MR}_3^2
Ride-height drop under aero load
Δh=ΔFaeroKheave\Delta h = \frac{\Delta F_{aero}}{K_{heave}}
ΔFaero\Delta F_{aero}
axle downforce increase (N)
KheaveK_{heave}
axle heave rate – use the ride rate (tyres in series) when Δh is ride height
Parallel descent (constant rake)
Kride,fKride,r=Faero,fFaero,r,Kride=KheaveKt,axleKheave+Kt,axle\frac{K_{ride,f}}{K_{ride,r}} = \frac{F_{aero,f}}{F_{aero,r}},\quad K_{ride} = \frac{K_{heave}K_{t,axle}}{K_{heave}+K_{t,axle}}
KrideK_{ride}
axle heave ride rate, suspension in series with tyres (N/mm)
Kt,axleK_{t,axle}
sum of the two tyre rates on the axle (N/mm)

Trackside takeaways

  • Third spring acts in heave only; ARB in roll only; corner springs in both.

  • Single-wheel stiffness ≈ K_w + ½ ARB + ¼ heave element – that is what the driver feels over kerbs.

  • Heave packers/gap are the main ride-height-at-speed tool on prototypes and FIA formula cars.

  • Heave ride-rate ratio front/rear (tyres included) ≈ aero load ratio front/rear for constant rake at speed.

  • Heave changes also change pitch stiffness – check braking/accel platform.

On your car

No third element. Platform comes from corner springs plus bump stops (and their gaps), which also act in roll – a key difference from prototypes.

Check yourself

Question 1 / 4L1 · Foundation

Which statement about a third (heave) spring is correct?

Further reading
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 16 Ride and Roll Rates
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 21 Suspension Springs
  • Segers – Analysis Techniques for Racecar Data Acquisition — §12.5 Modal Analysis · heave/pitch/roll/warp modes and modal stiffness matrix