Bump stops, packers and progressive rates
Bump stops (bump rubbers) and packers turn a linear suspension into a progressive one. Used deliberately they control ride height at speed – the aero platform – while keeping softer springs for low-speed grip; used carelessly they cause sudden balance shifts.
Bump stops, packers and progressive rates: L1 Foundation explanation
Not just a travel limiter
A bump stop (bump rubber) is an elastomer (or stack of polyurethane/microcellular foam, sometimes disc springs) on the damper shaft. Once the damper has compressed by the gap, the stop contacts and adds a strongly progressive rate in parallel with the main spring. A packer is a spacer (often 1–2 mm shims) that reduces that gap.
Why race cars use them on purpose:
- Downforce rises with . Springs soft enough for slow corners would let the car sink far too much at Vmax.
- With a stop, the car runs on the spring at low speed (mechanical grip, kerbs) and on spring + stop at high speed (platform).
So the effective wheel rate becomes speed- (load-) dependent:
where is zero until the gap is closed and then rises steeply – often from a few hundred N/mm at first contact to several thousand N/mm after 5–10 mm.
Typical use: GT3 cars routinely spend a large part of the lap on the front bump rubbers (braking, high-speed corners). Prototypes and formula cars do the same with packers on the heave element.
Trap: the bump stop also acts in roll on the outside wheel. If it engages mid-corner, that axle's roll stiffness suddenly jumps → LLTD shifts to that axle → sudden understeer (front) or oversteer (rear).
Bump stops, packers and progressive rates: L2 Practitioner explanation
Setting gaps and reading the data
Measuring the gap. Measure free gap on the damper shaft at static ride height with driver and fuel (or ballast): distance between bump rubber and the damper body/cap. Convert to wheel travel with MR: . Statically the spring carries the same corner load whatever you adjust, so its compressed length is fixed – that decides what each adjuster does:
- Ride height via the spring perch (preload collar) changes the static damper length. The measured gap grows or shrinks by the perch change (in damper mm), but the stop still contacts at the same damper length, i.e. the same body-to-wheel position, so the ride height at contact is unchanged.
- Ride height via pushrod length or damper/eye length (the separate length adjuster many coil-overs have) leaves the spring and damper at the same static position, so the static gap is unchanged, but the ride height at which contact occurs moves by the same amount as the ride-height change.
Know which adjuster your car uses, and re-measure the gap after any perch change.
Data checks
- Overlay damper position with the contact threshold (gap) – compute "% of lap on bump stop" per corner and where it happens.
- Plot ride height (laser) or damper position vs speed: the slope flattens when the stop engages – that's your platform knee.
- Estimate bump-stop force from manufacturer curves (force vs compression) to see how much of the aero load it carries.
Typical trackside moves
| Problem | Bump-stop lever |
|---|---|
| Front too low at Vmax / splitter grounding | reduce front gap (add packer) or harder rubber |
| Understeer only in fast corners | check outside-front contact mid-corner – increase front gap or softer rubber |
| Rear instability in high-speed braking | front dives onto/through its stop and aero balance moves forward – more front support (less gap/harder rubber), check rear droop |
| Car harsh over kerbs | stops engaging on kerb strikes – more gap or softer rubber |
Progressive rate via geometry. Rising-rate rockers do something similar continuously. The difference: the stop gives a defined knee, which is predictable for aero work but can feel abrupt; a rising rocker is smoother but fixed by design.
Pitfalls: worn/heat-aged rubbers change rate (check them every event); stops on left and right must be identical in length and spec (asymmetry = left/right balance difference); never compare gaps between cars with different motion ratios without converting to wheel travel.
Bump stops, packers and progressive rates: L3 Advanced explanation
Designing the knee
Ride height vs speed with a linear suspension and a stop engaging at wheel travel . The stop is in parallel with the suspension spring only; the tyres are in series with both, so write suspension travel and tyre deflection separately (axle quantities, wheel-referred, = suspension heave rate without tyres):
The tyre term keeps its full slope after contact – on a stiff stop it becomes the main source of further ride-height loss, which is why tyre pressure matters so much for Vmax ride height.
(using an equivalent linear for the stop; real stops are progressive so the second slope keeps flattening). Pick so contact begins around the speed above which aero platform matters more than compliance – often 150–200 km/h on GT3 – and pick the rubber so ride height at Vmax stays inside the aero map's good region.
Interaction with balance
- In heave/pitch: stops at the front engaged in braking increase front pitch stiffness → less dive, less aero-balance shift forward. Good for high-speed braking stability; but the front is now very stiff over bumps under braking → lock-ups and ABS activity rise.
- In roll: only the outside stop engages (the inside wheel extends). Roll stiffness on that axle increases by roughly (one wheel only) – a large and non-linear shift of LLTD. This is how GT3 cars can be neutral at 120 km/h and understeer at 220 km/h even with modest aero balance change.
- Combined: in high-speed corners on an aero car, heave from downforce brings both stops closer, so roll engages the outside one sooner. Gap decisions are therefore speed- and g-dependent; build a simple map (gap closure vs speed and ) from the data.
Damper interplay. When a stop engages, the effective spring jumps but the damper doesn't: damping ratio falls (by ~30–60 % at large stop rates) → body oscillation on the stop, "skittish" fast corners. Some teams add high-speed bump or use hydraulic bump stops for this reason.
Bump stops, packers and progressive rates: L4 Expert explanation
Edge cases
- Energy and rebound. Elastomer stops have hysteresis (some damping) but return their stored energy in rebound. A hard stop strike at kerbs returns energy into rebound – the wheel and body are launched. That is why kerb setups combine more gap with appropriate high-speed rebound damping.
- Temperature and ageing. Microcellular PU stops soften with temperature and permanently set (shorten) with use; a 2 mm permanent set opens the gap by 2 mm – the same as removing a 2 mm packer: the stop engages later and the car runs lower at Vmax. Measure free length.
- Using stops as the main spring. Some GT3 philosophies run soft main springs and let the stops carry most of the aero load (very progressive car). Pros: great low-speed grip and kerbs. Cons: high-speed balance becomes very sensitive to ride height and fuel load (heavier car closes the gap earlier), and to tyre pressure (tyre rate in series). Track stop contact vs fuel load through the stint.
- Aero stall and stops. On ground-effect cars a stop that keeps the floor just above the stall height is a safety net against porpoising; but if the floor's optimum lies on the stop, you are running on a very stiff element with poor damping – contact-patch load fluctuation and plank wear rise sharply.
- Asymmetric stops (different gaps left/right) are a deliberate tool on ovals and for tracks dominated by one corner direction – but they make the car's balance direction-dependent; document and communicate it.
Key formulas
- bump-stop rate at compression x (N/mm, zero below gap)
- gap measured at damper (mm)
- static ride height (mm)
- gap at wheel (mm)
- axle suspension heave rate without tyres (N/mm)
- equivalent linear stop rate at the wheel (N/mm)
- sum of the axle tyre rates (N/mm)
Trackside takeaways
Bump stops and packers make the suspension progressive: soft at low load, stiff at high aero load.
Gap is measured on the damper shaft; convert to wheel travel with MR before comparing.
Stops act in roll on the outside wheel only – mid-corner contact shifts LLTD suddenly.
Damping ratio drops when a stop engages; expect oscillation unless high-speed damping is adequate.
Inspect rubbers every event: permanent set opens the gap like an unplanned packer removal – the car runs lower at speed.
On your car
Bump-stop gap and rubber specification are among the most powerful GT3 setup tools; many cars spend a large part of the lap on the front stops. Fuel load changes gap closure through a stint.
Check yourself
A GT3 car is neutral in medium-speed corners but understeers in fast corners, with little aero-balance change expected. Damper data shows the outside front reaching its bump stop only in fast corners. What is happening?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 21 Suspension Springs · progressive springs and bump rubbers
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 16 Ride and Roll Rates
- Segers – Analysis Techniques for Racecar Data Acquisition — §9.6 Suspension Troubleshooting · non-linear roll curves from progressive elements