Longitudinal load transfer, pitch and anti-geometry
Braking moves load to the front and acceleration to the rear by m·a_x·h/L. Springs and anti-dive/anti-squat geometry do not change that total; they decide how much pitch it causes, which matters for aero platform, braking stability and traction.
Longitudinal load transfer, pitch and anti-geometry: L1 Foundation explanation
Under braking the inertial force at the CG pushes forward above the road, so load moves from the rear axle to the front axle. Under acceleration it moves rearward:
Example (GT3-like): kg, m, m, braking at 1.8 g (possible at high speed with downforce):
That is ~390 kg-equivalent added to the front axle and removed from the rear. With 45% static front weight (~5.7 kN front axle), the front axle load rises by roughly two-thirds.
Consequences:
- Braking: the rears unload, so the brake balance must be front-biased (typically 55–70% front on race cars, depending on CG height, downforce and tyre sizes). Rear lock-up or instability follows if it isn't.
- Turn-in on the brakes: high front load and low rear load make the car pointy, or unstable at the rear.
- Acceleration: load moves onto the rears, helping traction on RWD cars and hurting FWD cars (TCR), whose driven axle is unloaded as it accelerates.
As with lateral transfer, only mass, CG height, wheelbase and acceleration change the total. Springs and geometry change pitch, not the total.
Longitudinal load transfer, pitch and anti-geometry: L2 Practitioner explanation
Pitch. The load transfer passes either through the springs (compressing the front and extending the rear: pitch) or through the suspension links (anti-geometry). With anti-dive geometry, the link forces carry part of the braking load transfer directly, so the springs see less and the car dives less.
| Term | Acts in | Effect |
|---|---|---|
| Anti-dive (front) | braking | less front compression |
| Anti-lift (rear) | braking | less rear extension |
| Anti-squat (rear, driven) | acceleration | less rear squat |
| Anti-lift (front, driven front axle only: FWD/AWD/LMH front motor) | acceleration | less front rise |
Misconception to kill early: anti-geometry does not reduce longitudinal load transfer. The total is regardless. Anti-geometry changes the path, and therefore the pitch angle.
Why pitch matters trackside:
- Aero platform. On ride-height-sensitive cars (LMP, formula, GT3 with splitter/diffuser) the front drops and rear rises under braking. Aero balance usually shifts forward as the front gets closer to the ground, so the car can become oversteery on entry at high-speed braking zones. Heave springs, bump stops/packers and anti-dive control this.
- Braking feel and stability. Too much anti-dive gives a "wooden" brake feel and kickback, and the suspension is less compliant over bumps under braking.
- Traction. Anti-squat on a RWD car keeps the rear from squatting, which keeps the rear wing and diffuser at a better attitude. Too much anti-squat can make the rear "hop" or lose compliance over bumps in traction.
Measuring: the pitch gradient (Segers §9.7: chassis pitch angle at the centreline per g of longitudinal acceleration, from the suspension potentiometers); front and rear ride-height changes per g from lasers are a useful extension. Compare braking and traction pitch gradients against target values used for aero mapping.
Longitudinal load transfer, pitch and anti-geometry: L3 Advanced explanation
Anti percentages (side-view geometry). For outboard brakes, the braking force acts at the contact patch. If the side-view instant centre lies on a line from the contact patch at angle above horizontal, the fraction of front transfer taken by the links is
with the front brake-force fraction. For inboard brakes or drive torque reacted by the chassis (inboard diff, independent suspension), the line is drawn from the wheel centre instead, and the achievable anti is smaller for the same geometry. 100% anti-dive means zero front spring compression under braking. Race cars typically run tens of percent, not 100%, because of the compliance and feel trade-offs.
Traction limit with transfer (RWD, rigid, no aero): rear load is (with = CG to front axle distance), so
GT3 example: , , gives g in low gears. The car is traction-limited only in first and second gear exits; above that it is power-limited. For FWD (TCR) the sign flips: , which is much lower for the same μ. That is why exit traction is the front-drive car's big constraint.
Combined with lateral. In trail braking both transfers act together: the outside front tyre carries static + longitudinal + lateral load, and the inside rear is the lightest tyre on the car. That is why inside-rear lock-up and entry instability appear on high-CG, short-wheelbase cars.
Aero contribution. Drag acts at its own height above the ground, not at the road, so it creates a nose-up moment that moves load from the front axle to the rear. If is the total deceleration (including the drag part), the true forward transfer is , which is always less than (and, when , even less than the transfer from the tyre braking force alone). At constant speed, drag alone moves from the front axle to the rear: a GT3 at 250 km/h with m² has kN, and with m that is ~0.5 kN. Front/rear downforce measured at the axles in a wind tunnel or from load data already contains this drag pitching moment, so don't add it twice. Downforce also moves with pitch: under braking the front ride height falls, so on most cars front downforce rises and aero balance shifts forward. This is coupled with mechanical pitch through the heave/pitch stiffness.
Longitudinal load transfer, pitch and anti-geometry: L4 Expert explanation
Dynamic subtleties.
- Pitch dynamics and tyre load. At brake application the pitch motion overshoots if pitch damping is low. Dynamic front load briefly exceeds the steady value and the rear dips below it. A sharp initial brake pressure rise (racing drivers often hit 80–100% pressure within 0.1–0.2 s) excites this, so rear stability in the first 50 ms of braking depends on pitch damping and the rear bump-stop/packer state.
- Anti-geometry and suspension modes. Anti-dive couples braking force into heave and pitch. Over bumps under braking the effective wheel rate and damping change with anti percentage, so the car's braking-zone ride differs from its straight-line ride. Very high anti also produces lateral-load-dependent jacking in combined braking and cornering.
- Pitch-sensitive aero. With aero maps , the "longitudinal load transfer" the tyres see includes the change in front and rear downforce with pitch. Lap simulations need a pitch/heave platform model; a rigid-pitch assumption mispredicts entry balance on LMP/formula cars.
- Long-wheelbase vs short-wheelbase. Longer reduces transfer per g and slows pitch dynamics. It also changes yaw inertia per mass. Comparing GT cars of different wheelbase on longitudinal transfer alone misses this.
- Data method. Total longitudinal transfer can be computed as a math channel (). Comparing it with measured front/rear load-cell differences and pitch gives the effective anti percentage under real conditions. That is a good check of whether suspension geometry matches the design data after a crash repair.
Key formulas
- longitudinal acceleration (m/s²)
- h
- CG height (m)
- L
- wheelbase (m)
- side-view angle from contact patch to instant centre
- front brake-force fraction
- a
- CG to front axle distance (m)
- tyre friction coefficient
- b
- CG to rear axle distance (m)
Load transfer & corner loads
Split lateral load transfer into geometric, elastic and unsprung components per axle and see the resulting LLTD and four corner loads.
| Axle | Geometric [N] | Elastic [N] | Unsprung [N] | Total [N] | Total [kg] |
|---|---|---|---|---|---|
| Front | 152 | 1850 | 218 | 2219 | 226 |
| Rear | 370 | 1561 | 250 | 2181 | 222 |
| Corner | Load [N] | [kg] |
|---|---|---|
| Front in | 827 | 84 |
| Front out | 5265 | 537 |
| Rear in | 1395 | 142 |
| Rear out | 5757 | 587 |
Aerodynamic downforce is not included. Load transfers are superimposed (lateral + longitudinal).
Trackside takeaways
ΔW_x = m·a_x·h/L. Anti-geometry and springs do not change it, only how much the car pitches.
At 1.8 g braking a GT3 moves ~3.8 kN to the front, which is why brake balance is strongly front-biased.
Pitch matters mostly through aero: front down under braking usually shifts aero balance forward (entry oversteer).
Anti percentages are tens of percent on race cars; too much costs brake feel and compliance.
RWD gains traction from transfer; FWD loses it. TCR exit traction is fundamentally limited.
On your car
High CG relative to wheelbase and big aero-assisted braking: large forward transfer. Brake bias is typically well forward, with in-car bias adjustment used as fuel burns and tyres wear. Splitter ride height under braking is the key aero-platform constraint.
Check yourself
A car with m = 1300 kg, h = 0.45 m, L = 2.70 m brakes at 1.5 g. What is the longitudinal load transfer?
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.2 Longitudinal Weight Transfer
- Segers – Analysis Techniques for Racecar Data Acquisition — §9.7 Pitch Gradient
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 18 Wheel Loads
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 17 Suspension Geometry · Anti-dive / anti-squat
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking