Learn / Data Acquisition & Analysis / Track data and track characterisation
L2 · Practitioner

Track data and track characterisation

Data tells you what kind of circuit you are at: speeds, gear usage, brake energy, full-throttle share, corner direction balance, g-g quadrant usage and bumpiness. Use these numbers to choose the baseline setup and tyre pressures before turning a wheel.

Track data and track characterisation: L1 Foundation explanation

Questions to answer about a track:

  • Fast or slow? (top speed, average speed, number of slow vs fast corners)
  • Mechanical grip or aero grip dominant?
  • Ratio of left to right corners?
  • Hard on brakes? On tyres? On the engine?
  • Which gears are used most?
  • Smooth or bumpy, kerb-heavy?

Some answers come from the layout; the rest from a single lap of data. Segers' Nogaro (3.45 km, 13 turns, 5 left/8 right) with a GT3 car: top speed 256 km/h, average 163 km/h, minimum 67 km/h, 22 gearshifts per lap, max lateral 2.37 g in left-handers (the fast ones) vs 2.00 g in right-handers, max acceleration 0.84 g, max braking −1.95 g.

Speed and gear histograms show how much of the lap is spent in each speed band and gear – a direct pointer to aero level and gearing. A track spending most time above 180 km/h rewards downforce and platform; one dominated by 60–120 km/h rewards mechanical grip and traction.

Full-throttle share indicates engine and fuel stress and the drag/downforce trade-off. Indicative GT3 orders of magnitude (threshold-dependent; check your own team data): Monza roughly 65–75 %, Spa 55–65 %, Hungaroring or Zandvoort 40–50 %. The one sourced figure is Segers' Nogaro GT3 example at about 26 % of lap time at full throttle (he defines full throttle as > 95 %). Always state the threshold – 98 % versus 100 % throttle can move the figure by several points.

Key formulas

Brake energy per stop
Estop≈12meq(Vstart2−Vend2)−∫Fdrag dsE_{stop} \approx \tfrac{1}{2} m_{eq} \left(V_{start}^2 - V_{end}^2\right) - \int F_{drag}\,ds
meqm_{eq}
vehicle mass plus rotating inertia, ≈1.03–1.05 m (kg)
Vstart,VendV_{start}, V_{end}
speeds at brake on/off (m/s)
FdragF_{drag}
aerodynamic drag during the stop (N)
Time in g-g quadrant (% of lap)
TQ=100tlap∫0tlapcQ(t) dtT_{Q} = \frac{100}{t_{lap}}\int_0^{t_{lap}} c_Q(t)\,dt
cQc_Q
1 when |G_lat| and |G_long| exceed their deadbands with the quadrant’s signs, else 0

Trackside takeaways

  • One lap of data characterises a track: speeds, gear use, brake energy, full-throttle %, quadrant usage, bumpiness.

  • Quadrant usage predicts which tyre should run hottest; use deadbands and energy weighting, and set cold-pressure offsets from measured hot pressures.

  • Prioritise setup changes for the quadrant/phase where the car spends the most time.

  • Compare bumpiness metrics only at identical sampling and calculation rates.

  • Tag track metrics with conditions; rubber and temperature change the track through a weekend.

On your car

Brake energy and quadrant usage predict per-corner cold-pressure offsets (confirm them with measured hot pressures) – with mandatory minimum pressures in some series, the hardest-working tyre still needs careful targeting.

Check yourself

Question 1 / 3L2 · Practitioner

After a 10-lap GT3 run, all four tyres started at 1.45 bar cold (gauge) and the hot target is 1.85 bar. Hot pressures: LF 1.92, RF 1.80, LR 1.98, RR 1.83 bar – the LR, as the quadrant analysis predicted, runs hottest. Using the ideal-gas ratio of absolute pressures (p_atm = 1.013 bar), what cold pressure should the LR get next run?

Further reading
  • Segers – Analysis Techniques for Racecar Data Acquisition — Ch. 18 Racetrack Characterization (§18.1–18.5)
  • Segers – Analysis Techniques for Racecar Data Acquisition — §15.4 A Worked out Example · cross-weight optimum and track asymmetry