Setup for track characteristics
Every circuit pulls the setup in a different direction: bumps want compliance, high-speed tracks want platform and low drag, street circuits want ride height, steering lock and stability, kerb-heavy tracks want controlled high-speed damping, and temperature shifts the tyre window. Start the weekend from the right baseline.
Setup for track characteristics: L1 Foundation explanation
Before arriving at a circuit, classify it. The main characteristics and their usual setup direction:
| Characteristic | Examples | Setup direction |
|---|---|---|
| Bumpy | Sebring, Long Beach, old airfields | Softer springs and high-speed damping, higher ride height, softer bump rubbers |
| High-speed / low-drag | Monza, Le Mans, Spa (sector 1/3) | Less wing, stiffer platform (heave), lower ride heights, longer gearing |
| Street circuit | Macau, Pau, Long Beach, Baku | Higher ride height, more steering lock/Ackermann for hairpins, more downforce, stability under braking, brake cooling |
| Kerb-heavy | Zandvoort, Red Bull Ring, Monza chicanes | Compliant high-speed bump, ride height margin, strong suspension parts, kerb-friendly diff/TC |
| Hot track | Summer races, Bahrain day | Lower cold pressures, more cooling, guard rear tyres (oversteer tendency), possibly harder compound |
| Cold / green track | Early-season, morning sessions | Higher cold pressures, more aggressive warm-up, softer car for mechanical grip |
The goal is not to find a universal "best" setup but to give the driver a car that is compliant enough to keep the tyres on the road, stable enough to commit, and efficient enough (drag vs downforce) for the track's mix of corners and straights.
A practical tool: the corner speed histogram of the circuit (time spent per speed band). A track with most cornering time below 120 km/h is a mechanical-grip track; one with most time above 180 km/h is an aero track. This tells you where to put development effort.
Setup for track characteristics: L2 Practitioner explanation
Practical decisions per track type:
Bumpy tracks. Grip comes from keeping the tyre load variation low. Soften springs 10–20%, soften high-speed bump (and sometimes high-speed rebound) 2–4 clicks, raise ride height 2–5 mm to avoid bottoming and plank wear, increase bump-rubber gaps. Accept some aero loss: a car that bottoms or skips loses more than it gains from 3 mm lower ride height. Data check: damper velocity histograms – wider high-speed tails than baseline mean the track is exciting the wheel; ride-height minima at the bumps vs splitter/skid limits.
High-speed tracks. Low drag: reduce rear wing (and front to keep balance). Platform matters more because downforce loads are larger: stiffer heave/third springs or packers to control ride height at 250–300 km/h; check bottoming at the end of straights and in compressions (Eau Rouge, Raidillon). Gear ratios: top gear at the limiter just before the braking point of the longest straight, with tow margin.
Street circuits. Bumps, crowns, manhole covers, low grip that evolves quickly, walls punishing mistakes. Raise ride heights 3–8 mm vs a permanent circuit; soften; increase steering lock (Macau's Melco hairpin, Monaco's Fairmont, ex-Loews, hairpin) – check lock-to-lock and Ackermann; brake cooling up (repeated heavy stops); more rear stability on entry (driver confidence near walls is worth more than ultimate rotation). Expect track evolution of several seconds per lap over the weekend – don't over-react to Friday balance.
Kerbs. Decide which kerbs the driver must use. Soften high-speed bump (blow-off) so the wheel climbs without launching the chassis; enough ride height and packer gap so the car does not ground; a slightly softer rear ARB helps the car ride over an inside kerb on exit. TC/diff that tolerate an unloaded wheel.
Temperature. Track temperature changes of 10–20 °C between sessions raise the tyres' gas temperature by part of that amount (measure it with TPMS), typically moving hot pressures by ~0.05–0.15 bar, and change the tyre's grip window. Hotter → reduce cold starting pressures, more cooling for brakes and engine, and expect more rear degradation (oversteer late in a stint) on rear-limited cars.
Setup for track characteristics: L3 Advanced explanation
Quantifying the track. Use previous data or a lap sim to compute: (a) the fraction of lap time in speed bands (mechanical vs aero sensitivity); (b) time at full throttle (drag/power sensitivity – Segers' full-throttle-per-lap metric); (c) lateral g histogram (where grip matters); (d) road roughness from damper velocity histograms or ride-height PSD (Segers Ch. 11–12). Lap-time sensitivity to vs ( and ) sets the wing level: on Monza a GT3 may lose more from 1% drag than it gains from 1% downforce; at Hungaroring the opposite.
Bumpy vs smooth – the compliance trade. The vertical tyre load variation (standard deviation) reduces average grip because of load sensitivity: the tyre loses more grip on the unloading half-cycle than it gains on the loading half. Compliance reduces the variance, aero platform demands stiffness. The optimum moves with roughness: the classic two-mode trade (body mode ~2–5 Hz controlled by springs/LS damping; wheel-hop mode ~12–20 Hz controlled by HS damping and tyre stiffness). On bumpy tracks race cars are often damped harder at high shaft speed than the grip optimum: on sharp inputs the damper force ( at 300–500 mm/s) passes straight into the tyre and the chassis. Reducing HS damping lowers these force spikes and the tyre-load variance – provided the wheel-hop mode stays controlled. Too little damping lets the wheel hop (lower unsprung damping ratio, higher resonant peak) and rises again: there is an optimum, and you accept more body motion to get near it.
Street-circuit evolution. Grip may go from to 1.5 over a weekend on slicks. Balance usually moves toward oversteer as grip rises (more rear-limited because of higher lateral and longitudinal demand on rear tyres and higher temperatures). Build a baseline with a margin of understeer early, and plan bar changes as the track rubbers in.
Kerb strikes as load cases. A kerb produces an impulse at the wheel; high-speed damping force at 300–500 mm/s determines how much is transmitted to the chassis. Too stiff → chassis launched, landing on bump stops, snap; too soft → wheel travels into bump rubber anyway. Look at damper position and velocity during kerb strikes and at the time to settle.
Temperature and tyre window. For a given compound, the grip vs temperature curve has a plateau; hotter ambient shifts the operating point up. The setup response: reduce energy into the overheating axle (less sliding: balance, toe, camber), lower cold pressures to hit the same hot target, use harder compound if allowed. Cold conditions: the opposite plus warm-up management (more aggressive out-lap, higher blanket temps where permitted).
Trackside takeaways
Classify the track: bumpy, high-speed, street, kerb-heavy, temperature – each pulls setup differently.
Bumpy: soften springs and HS damping, raise ride height; compliance beats a lower but unstable platform.
High-speed: low drag, firm platform, gearing to the longest straight with tow margin.
Street: ride height, steering lock, stability, brake cooling; expect large track evolution.
Kerbs: soft HS bump, ride-height margin, tolerant diff/TC.
Hot track: lower cold pressures, protect the rear axle, more cooling.
On your car
BoP often sets ride-height and wing ranges per track; Le Mans/Monza use low-drag wing positions. Check homologated options early.
Check yourself
Moving from a smooth permanent circuit to a very bumpy one, which change is the most typical starting point?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 12 Chassis Set-up
- Segers – Analysis Techniques for Racecar Data Acquisition — §17.3 How to Create Metrics · full throttle per lap and other track metrics
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.4 The Shock Speed Histogram · track roughness from damper velocity distribution
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.4 Suspension Optimization Using Frequency Analysis