Tyre-driven setup decisions
Hot pressure targets, temperature-based camber decisions and degradation management turn the tyre from a black box into a setup input. The best setup is the one that keeps all four tyres in their window for the whole stint.
Tyre-driven setup decisions: L1 Foundation explanation
The tyre works in a window: a range of temperature and pressure where it produces peak grip. Outside the window it slides more, wears faster and the balance changes.
Pressure targets. Tyre suppliers and teams specify a hot pressure target (e.g. ~1.8–2.0 bar for many GT3 slicks; minimum starting pressures are mandated in some series). You set cold pressures so that after 2–4 laps the hot pressure reaches the target. Pressure rises with gas temperature – roughly 0.1 bar per 10 °C. If the target is missed, adjust the cold pressure for the next run.
Temperature profile. A pyrometer (probe) measures inner, middle and outer tread temperature after a run; IR sensors on the car measure it live. Read it like this:
- Middle hotter than the average of the edges → pressure too high (crowned contact patch).
- Middle cooler → pressure too low.
- Inside much hotter than outside → too much negative camber (or too much toe).
- Outside hotter than inside → too little negative camber.
A typical cambered race tyre runs the inside a few degrees to ~10 °C hotter than the outside after a representative run.
Degradation. Grip falls over a stint through wear and heat cycles and, mostly, through overheating the surface. The axle that overheats first drives the balance: if the rears overheat the car becomes loose late in the stint. Setup can reduce the energy put into the critical axle.
Tyre-driven setup decisions: L2 Practitioner explanation
Getting the pressure right
- Use TPMS (pressure + gas temperature) where fitted: it shows the warm-up curve and stabilised hot pressure per lap, not just one pit-lane reading. Segers (§8.2 Working with Tire Pressure Monitoring Systems) uses TPMS run charts to show how many laps the pressures need to stabilise – which is why balance judgements made after three laps are unreliable – and back-calculates the cold pressure from the hot reading with the ideal gas law.
- Correct cold pressure by the error: if the target is 1.90 bar hot and you reached 2.02 bar, drop the cold pressure by ~0.10–0.12 bar (the rise is roughly proportional to absolute pressure).
- Watch blanket temperatures and ambient: a cold-pressure setting is only valid with the same blanket temperature and similar track temperature.
- Front/rear and left/right differences: tracks with more right-hand corners load the left side tyres more; set side-specific cold pressures to land all four on target.
Camber from temperatures (with caveats)
- Probe readings after the in-lap reflect the in-lap, not the qualifying lap. Prefer IR sensor data in the relevant corners, or have the driver push until the pit entry.
- Typical targets: inside–outside spread ~5–10 °C; middle within a few degrees of the edge average.
- If spread is too large, reduce negative camber 0.25–0.5° (also check toe – toe-out heats the insides). If too small (outside hot), add camber.
- Optimum camber is ultimately a lap-time / grip decision, not a temperature-symmetry decision; the outside tyre in a corner wants more negative camber than the static reading suggests because of roll and tyre deflection.
Degradation management
- Identify the limiting axle with a run chart of balance (average understeer angle per lap) and lap time over a long run, corrected for fuel.
- Front-limited: protect the front with less entry rotation demand, a bit less front toe-out, less front camber if wear is on the inside.
- Rear-limited: more rear stability (rear toe-in +0.5 mm, softer rear ARB, more diff locking to reduce inside spin, smoother throttle map, TC higher), start the stint with a bit more understeer.
- Thermal vs mechanical deg: if lap times recover after a cool-down lap, deg is thermal (manage energy). If not, it's wear (manage sliding).
Tyre-driven setup decisions: L3 Advanced explanation
Physics of the pressure target. Pressure sets carcass stiffness and contact patch shape: lower pressure → longer, more compliant patch, higher cornering stiffness at low load but more sidewall flex, heat generation and a peak at higher slip angle; higher pressure → crisper response, smaller patch, lower peak grip and earlier fall-off. Suppliers set a window that balances grip and structural safety (bead/sidewall). Within it, the lap-time optimum is usually narrow (±0.05 bar). Apply the metric-vs-lap-time method (Segers §17.2, Fig. 17.4) to tyre pressure: plot fuel-corrected lap time or grip factor against hot pressure across runs and look for the optimum rather than trusting a single number.
Gas law correction. At constant volume, . From cold to hot : with temperatures in kelvin. E.g. 1.40 bar gauge at 20 °C reaching 75 °C gas temperature: bar. Volume growth of the tyre at speed slightly lowers the real rise. Nitrogen or dry air reduces moisture-induced scatter.
Camber and temperature – what the probe can and cannot tell. The tread temperature distribution integrates the whole lap: straights (camber gives inside heating with no benefit), braking and both corner directions. The outside tyre in a long corner may want more negative camber than temperatures suggest. A better method: IR sensor arrays gated on lateral g (outside tyre, g) to read the cornering temperature profile; or test camber directly on lap time with fixed pressures.
Degradation decisions. Fit a model of lap time to long runs to separate tyre deg from fuel effect. Compare setups on , not just on : a setup 0.10 s faster on lap 1 but losing an extra 0.02 s each lap is slower over a 30-lap stint: its average deg penalty is s/lap against a 0.10 s/lap head start, a net loss of ≈0.19 s/lap (≈5.7 s over the stint). It leads on cumulative time only for the first ~11 laps – a qualifying or sprint answer, not a stint answer. Track the per-tyre energy (sliding power ) in simulation or approximate with lateral g and understeer angle metrics.
Key formulas
- hot gauge pressure (bar)
- cold gauge pressure (bar)
- atmospheric pressure ≈ 1.013 bar
- hot gas temperature (K)
- cold gas temperature (K)
Trackside takeaways
Set cold pressures to hit the hot target; ~0.1 bar per 10 °C gas temperature.
Middle hotter than edges → pressure too high; much hotter inside → too much camber (or toe-out).
Prefer live IR/TPMS data gated on cornering over pit-lane probe readings.
Identify the limiting axle over a stint; set up to protect it.
Compare setups on degradation rate, not only on fastest lap.
Re-target pressures after any camber change.
On your car
Single-make tyre (Pirelli in SRO, Michelin/Goodyear elsewhere) with specified hot windows and sometimes minimum cold pressures; TPMS mandatory in many championships.
Check yourself
Probe temperatures after a run (I/M/O): 92 / 98 / 90 °C. What does this suggest?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 12 Chassis Set-up · tyre temperatures and pressure
- Segers – Analysis Techniques for Racecar Data Acquisition — §8.2 Working with Tire Pressure Monitoring Systems
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.5 The Understeer Angle · run chart of balance over a race