Brake temperatures & cooling: windows, carbon vs iron, ducts, glazing
Brakes convert ~1 MJ per front disc in a big stop into heat. Disc and pad compounds work in temperature windows; ducting, compound choice and bias keep them there. Brake heat also feeds tyre temperatures and pressures.
Brake temperatures & cooling: windows, carbon vs iron, ducts, glazing: L1 Foundation explanation
Energy. Brakes turn kinetic energy into heat. A 1350 kg GT3 braking from 280 to 80 km/h releases
After aero drag, engine braking and rolling resistance take their share (~10–15 %), roughly 60–65 % of the rest goes to the fronts: ~1 MJ per front disc in ~3 s, an average of ~330 kW per disc. At near-constant deceleration brake power is proportional to speed, so it peaks at the start of the zone at ~500–600 kW per disc (×77.8/50 m/s mean speed). With an iron disc of ~11 kg ( J/kg·K), that is a bulk temperature rise of ~180 K per stop — the surface sees much more.
Operating windows (typical, compound-dependent):
| Material | Usable window | Problems |
|---|---|---|
| Iron disc + race pad (GT, Cup, F4, FR) | ~300–650 °C, short peaks ~750 °C | Cold: low bite. Hot: fade, pad wear, disc cracking, fluid boiling |
| Carbon-carbon (F2, SF, IndyCar, LMP2, Hypercar) | ~400–900 °C, best ~500–800 °C | Cold: very low friction and poor bite. Hot: rapid oxidation wear |
Measurement: infrared sensors aimed at the disc face (Segers §5.8) — one front and one rear is usually enough; thermocouples in the caliper body (fluid temperature risk); temperature paint on discs during tests to see peak temperature.
Cooling: brake ducts take air from the front of the car (or the floor) and blow it onto the disc and caliper. Teams change duct size or blank off inlets in steps (e.g. 0/25/50/75 %) depending on the track, weather and race length.
Glazing: if pads run too cold for long periods (light braking, safety car) or are overheated, the pad surface can form a hard, smooth glaze with lower friction. New pads/discs also need bedding — a controlled heating cycle that lays down a transfer layer on the disc.
Why the race engineer cares beyond the brakes: brake heat soaks into the wheel rim and raises tyre temperature and pressure. Brake duct settings are therefore also a tyre-pressure tool, especially in GT3 and prototypes.
Misconception: "colder brakes are safer brakes." Below the window, friction and bite drop sharply (especially carbon) — cold carbon after a safety car is a classic cause of lock-ups and missed corners.
Brake temperatures & cooling: windows, carbon vs iron, ducts, glazing: L2 Practitioner explanation
Using temperature data (Segers §5.8).
- Range per lap: max/min/average disc temperature per lap in run charts; compare with the pad supplier's window.
- Temperature balance channel (Segers Eq. 5.4): — compare with the pressure bias. A change in bias shows up in temperature balance over several laps (thermal lag).
- Build-up rate gated with bar, and cooling rate gated with bar. The cooling rate per lap measures duct effectiveness; the build-up rate depends on driver, pad compound and master cylinders (Segers Eqs 5.5–5.10).
- Time above a critical temperature per lap (e.g. > 700 °C for an endurance iron-disc package) predicts wear and fade risk.
- Left vs right: circuits with mostly right-hand corners heat the brakes unequally; a big L/R difference in cooling after release, at low speed, can also mean a dragging caliper (Segers' Monza example) rather than ducting.
Choosing duct size.
- Use practice data to find the hottest braking zone's peak and the lap minimum.
- Target: peak inside the window with margin; minimum not falling below the bite threshold before the next big stop.
- Account for race conditions: traffic (less cooling air), full tanks (more energy), safety cars (cooling down), ambient temperature changes.
- Remember the cost: open ducts add drag (small, but non-zero) and may alter front aero; and they cool the rims (lower tyre pressure).
Compound choice. Segers' GT3 comparison of two pad compounds: compound B built temperature faster (more initial bite), had higher peaks and needed higher temperature to deliver higher friction; compound A needed more pressure but had more consistent release (better modulation) and less, more consistent time per lap above 700 °C (Segers §5.8, Fig. 5.22). For an endurance race, A; for a sprint where bite matters, possibly B. This is exactly the kind of trade the engineer must present to the driver.
Pad knock-back. Hub/bearing deflection under high lateral load or kerb strikes pushes pistons back; the next brake application has a long pedal. Drivers learn to tap the pedal on the straight before big stops. Track in pedal-travel-vs-pressure plots.
Fluid. Racing fluids have dry boiling points of ~300–330 °C; caliper body temperatures should stay well below that (aim < ~180–200 °C). A soft, long pedal late in a stint with high caliper temperatures = fluid boiling — open the ducts or add caliper cooling/heat shields.
Brake temperatures & cooling: windows, carbon vs iron, ducts, glazing: L3 Advanced explanation
Heat partition and disc thermal model. During the stop, friction power is split between disc and pad by the thermal effusivity ratio (); for iron discs with organic/metallic race pads typically ~90 % goes to the disc. A lumped model for the disc bulk temperature:
where depends on the duct mass flow (roughly ∝ for forced convection). Fit from the cooling phases of logged data (exponential decay toward ambient at speed), and from the build-up phases. Then predict temperatures for other tracks, duct settings and ambient conditions — a practical brake-cooling tool. Radiation matters above ~600 °C (especially carbon running at 800+ °C).
Carbon-carbon specifics. Friction coefficient increases strongly with temperature up to its working range, then plateaus; wear is dominated by oxidation above roughly 600–700 °C (bulk), increasing exponentially with temperature. So carbon disc wear (a key endurance constraint, measured in mm of thickness loss per race distance) is managed by keeping the peak and the time at high temperature down, even at the cost of slightly more drag from bigger ducts. Disc thickness is measured after sessions and plotted vs energy to calibrate a wear model per circuit.
Iron specifics. Thermal cracking from cyclic surface stress; disc slots/grooves and pad material mitigate. Pad friction vs temperature curves differ by compound; some have a strong "cold bite" deficit, others fade early. Thermal judder can appear from uneven transfer-layer deposits (often mis-called "warped discs").
System thermal coupling. Caliper temperature lags disc temperature by tens of seconds; rims lag even more (minutes). Tyre pressures therefore respond to brake cooling changes over several laps. In GT3 and Hypercar, where tyre pressure minimums are policed and tyre temperatures decide pace, duct settings are chosen as much for tyre pressure targets as for brake windows — particularly on the front axle and when tyres must be double-stinted.
Brake temperature balance as a diagnostic. The ratio of front/rear energy absorption follows the force split, not pressure. With a model of each axle's thermal capacity and cooling, measured temperature balance gives an independent estimate of the real force split (including engine braking and regen effects on the driven axle) — useful for checking BBW systems and engine-braking maps.
Key formulas
- disc mass (kg)
- specific heat (J/kg·K)
- heat fraction into disc
- h
- convective coefficient (W/m²K)
- disc surface (m²)
Trackside takeaways
A big GT3 stop puts ~1 MJ into each front disc in ~3 s: ~330 kW average, ~500+ kW at the start of the zone (P ∝ V).
Iron ~300–650 °C (peaks ~750); carbon ~400–900 °C, wear by oxidation above ~650 °C.
Gate dT/dt by brake pressure to separate build-up and cooling rates (Segers Eqs 5.5–5.10).
Cold carbon after safety cars and out-laps = low bite and lock-ups.
Brake ducts are also a tyre-pressure tool: brake heat soaks into the rims.
Long, soft pedal late in a stint + hot calipers = fluid boiling; gradual increase = pad wear.
On your car
Iron discs with endurance and sprint pad options; duct blanking is common and heavily used to tune front tyre pressures. Watch time above ~700 °C in long races.
Check yourself
A 1300 kg car brakes from 250 to 100 km/h. Approximately how much kinetic energy is released?
- Segers – Analysis Techniques for Racecar Data Acquisition — §5.8 Brake Temperature Measurement (Eqs 5.4–5.10, Figs 5.17–5.22)
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking