Total wheel loads: aero, transfer and estimation from data
Each tyre’s vertical load is the sum of static weight, lateral and longitudinal transfer, aero load, banking/grade and bump content. You can estimate it from accelerations and setup data, or measure it via damper potentiometers or load cells, as long as you know what each method misses.
Total wheel loads: aero, transfer and estimation from data: L1 Foundation explanation
"The principal task of the race engineer is to balance the vertical loads acting on the tyres" (Segers ch10). Each wheel's load is a sum of contributions:
Worked example: GT3 outside front (left front in a right-hander), 180 km/h, trail braking at 0.8 g with 1.4 g lateral. kg, 45% front, m, m, m, front LLTD 49%, m², aero balance 40% front.
| Contribution | LF (N) | RF (N) |
|---|---|---|
| Static (585 kg / 2) | 2869 | 2869 |
| Longitudinal (1700 N total, half per side) | +850 | +850 |
| Lateral front share (49% of 4870 N) | +2386 | −2386 |
| Aero (2297 N × 40% / 2) | +459 | +459 |
| Total | 6564 | 1792 |
The outside front carries 3.7× the inside front's load. Through tyre load sensitivity, the front pair is far from its ideal-grip state, which is why entry balance is so sensitive to LLTD, brake bias and aero balance under pitch.
Aero load is , split front/rear by the aero balance (which moves with ride height and pitch). Orders of magnitude for : GT3 ~1–2 m² (BoP and configuration dependent), LMP2/Hypercar ~3–4 m², F3 ~2–3 m², F2/Super Formula ~3.5–4.5 m². At 250 km/h, each 1 m² of is ~2.95 kN of downforce.
Total wheel loads: aero, transfer and estimation from data: L2 Practitioner explanation
Estimating wheel loads from data (Segers §10.4).
Method 1: from accelerations (simulation-style math channels). Use logged , and speed, plus setup constants (masses, CG, RCs, roll stiffness split, and balance). This is a model, not a measurement. It is good for understanding the order of magnitude and for corner-by-corner comparison, but it inherits every error in the constants.
Method 2: from damper potentiometers. Convert travel to wheel force for each element:
- spring: (MR = damper/wheel travel, the academy convention, so wheel rate = ), plus preload. Segers defines MR the other way round (wheel/damper; §10.4 Eq. 10.22, also used in Eq. 9.1): invert it when you use his equations;
- bump rubber/packer: non-linear once the gap is closed;
- ARB: proportional to the left–right travel difference, opposite sign on each side;
- damper: from a velocity–force map (separate low/high speed bump/rebound).
The sum gives the sprung (elastic) load change at each wheel. Add the unsprung and geometric transfer by calculation, because the pots do not see them.
Method 3: pushrod/strain-gauge load cells. Direct, high resolution and independent of rate assumptions. But again, not the unsprung, geometric or wheel-generated aero forces (open-wheel tyres and wheel fairings generate lift/downforce outside the sprung path).
Total download channel. Sum the four wheel loads (or load cells) minus static weight: you get the aero load (plus banking and vertical-curvature effects). Plotted against on straights and steady corners, the slope gives , an on-track estimate. The front/rear split gives aero balance vs speed. On an aero car the total-load trace looks like the speed trace squared; on a GT4 it barely moves.
Modal view. Decompose the four damper travels into heave, pitch, roll and warp (Segers §10.5). Each mode has its own stiffness, which gives clean per-mode forces and shows warp (diagonal) load from kerbs or chassis twist.
Total wheel loads: aero, transfer and estimation from data: L3 Advanced explanation
Error budget of each method.
- Acceleration-based: CG height (±10–20 mm typical uncertainty unless measured by tilting, Segers' raised-axle method), roll-centre migration, and aero balance changing with ride height, fuel burn. Use it for relative comparisons and to fill in components the sensors can't see.
- Pot-based: motion-ratio non-linearity (MR changes through travel by 5–15% on many pushrod layouts), spring-rate tolerance (±3–5%), packer and bump-rubber curves (temperature dependent), damper hysteresis and friction. Zeroing: pots must be zeroed at static ride height with the correct fuel and driver mass.
- Load cells: temperature drift, crosstalk from bending, calibration across the load range. They are the most accurate for the sprung path.
Tyre spring as a load sensor. Ride-height lasers measure to the ground, while pots measure suspension travel. Their difference, after geometry, is tyre deflection, and with a known tyre vertical rate (a few hundred N/mm for race slicks, pressure dependent) it is a load estimate that includes everything (unsprung, geometric, wheel aero). Segers §10.7 discusses tyre spring rates. It is noisy but a useful cross-check.
Consistency checks you should automate:
- Sum of wheel loads on a straight at constant speed = . A drift over a stint = fuel burn (good) or a sensor problem.
- Left–right sum difference ÷ should be stable (≈ × the share seen by the sensors, because one side gains while the other loses it). A change between runs without a setup change means damper/packer/bar link issues (Segers §9.6 troubleshooting).
- Front LLTD from load cells vs setup calculation, binned by and speed. Divergence at high speed = packers/bump rubbers or aero-induced ride-height effects.
Using wheel loads for engineering decisions: inside-wheel load near zero (TCR rear, GT4 inside front on kerbs) shows LLTD saturation. Minimum front load in high-speed braking zones guides bias and anti-dive. The outside-front load peak during trail braking sets the tyre's worst-case thermal input.
Total wheel loads: aero, transfer and estimation from data: L4 Expert explanation
From wheel loads to tyre-level understanding. Combine estimated per wheel with / and a mass-distribution model to estimate per-axle lateral force (moment balance with yaw acceleration ). Then normalise: axle is the axle friction utilisation. Plotting front and rear utilisation through a corner directly shows which axle limits the car in each phase, a data-driven pair analysis (RCVD Ch. 7). It is the most direct objective balance metric available without tyre force transducers.
Wheel force transducers (WFT, 6-axis hubs) remove most of the guesswork but are expensive, heavy and usually test-only. In series that allow them in testing, a single WFT test can calibrate your pot- and load-cell-based models for the season.
Dynamic content. Bumps and kerbs create high-frequency load variation. The standard deviation of tyre load (or of pushrod load), band-passed around wheel-hop frequency (~10–20 Hz), is a mechanical-grip metric. Because of load sensitivity, a tyre with large load variation produces less average force than a steady one. That is the quantitative basis for damper and spring tuning for grip (see the dampers domain).
Limits: none of these methods separate where on the tyre load is carried (camber, pressure distribution). And all of them assume the vehicle model (masses, geometry) is right. After a crash repair, re-verify CG, motion ratios and roll centres before trusting historical comparisons.
Key formulas
- aero balance (front fraction)
- downforce coefficient × area (m²)
- spring rate (N/mm)
- spring/damper travel from static (mm)
- MR
- motion ratio (damper travel / wheel travel); Segers uses the inverse
Load transfer & corner loads
Split lateral load transfer into geometric, elastic and unsprung components per axle and see the resulting LLTD and four corner loads.
| Axle | Geometric [N] | Elastic [N] | Unsprung [N] | Total [N] | Total [kg] |
|---|---|---|---|---|---|
| Front | 152 | 1850 | 218 | 2219 | 226 |
| Rear | 370 | 1561 | 250 | 2181 | 222 |
| Corner | Load [N] | [kg] |
|---|---|---|
| Front in | 827 | 84 |
| Front out | 5265 | 537 |
| Rear in | 1395 | 142 |
| Rear out | 5757 | 587 |
Aerodynamic downforce is not included. Load transfers are superimposed (lateral + longitudinal).
Trackside takeaways
Wheel load = static + lateral + longitudinal transfer + aero + banking/grade + bump content.
In trail braking a GT3 outside front can carry ~3–4× the inside front’s load.
Pots and load cells see only the sprung/elastic path; add unsprung, geometric and wheel aero by calculation.
Sum of wheel loads vs V² on straights gives an on-track C_LA and aero balance estimate.
Automate consistency checks: they catch sensor, packer and bar-link problems before they mislead setup work.
On your car
Damper pots are standard and load cells are less common in customer teams, so pot-based wheel-load channels are the norm. Aero is moderate, so mechanical transfer dominates wheel loads in most corners.
Check yourself
Using C_LA = 1.5 m², ρ = 1.225 kg/m³ and 40% front aero balance, what is the aero load on EACH front wheel at 180 km/h?
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.4 Total Wheel Loads
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.5 Determining Wheel Loads with Modal Analysis
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.6 Measuring Wheel Loads with Suspension Load Cells
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.7 Tire Spring Rates
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 18 Wheel Loads
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 7 Steady-State Pair Analysis · Axle utilisation view