Power steering & steering torque as a data channel
Power assistance changes how much of the tyre's message reaches the driver. A steering-torque channel lets the engineer see the front limit, driver effort and system health objectively.
Power steering & steering torque as a data channel: L1 Foundation explanation
Why race cars have power steering. GT and prototype cars have heavy front axles, wide slicks, big caster and high downforce. Unassisted steering torque would exceed what a driver can sustain over a stint (tens of N·m at the rim, peaks higher). Assistance lowers effort while trying to keep the shape of the torque signal – the feel.
Types
- Hydraulic (HPAS) – engine- or electric-pump-driven; assist force from a pressure difference across a piston on the rack, modulated by a torsion bar valve in the column.
- Electro-hydraulic (EHPAS) – electric pump, hydraulic rack; independent of engine speed.
- Electric (EPS) – electric motor on the column or rack, controlled by a torque sensor; assist curve programmable.
Who has it (generally): GT3, GT4, TCR, LMP2, Hypercar and Super Formula (KYB electric power steering since the SF19) – assisted. F4, Formula Regional, F3, F2 and IndyCar – unassisted (IndyCar's steering effort on street courses is notorious).
Steering torque as a channel. Measured with a strain-gauged column or quick-release hub, or taken from the EPS torque sensor via CAN. It is the torque the driver applies – on an assisted car not the total rack force.
What it tells you, basic level
- Steering effort per lap: peak and RMS torque → driver fatigue, especially relevant on unassisted cars.
- Torque rising with lateral g, then flattening or dropping while steering angle keeps increasing → front is saturating.
- Spikes on kerbs → kickback: the impact force acts through the wheel centre on the kingpin offset at hub height, plus caster/KPI jacking from the vertical hit.
Power steering & steering torque as a data channel: L2 Practitioner explanation
Assist and feel. Total rack force is shared:
With hydraulic assist, ; the valve opens more with torsion-bar twist, so assist rises with driver torque, often non-linearly (boost curve). Implications:
- Assist curve slope matters for feel. If assist grows steeply at high torque, the driver's torque saturates while rack force keeps rising – the SAT drop at the limit is compressed into a small change of driver torque: numb at the limit.
- Too little assist – heavy, tiring; the driver's precision falls over a stint.
- EPS maps (some cars/series allow selection): lower assist for fast tracks (more feel, effort tolerable), more for street tracks.
Building useful math channels
- Torque vs lateral g scatter per corner type: initial slope = steering "weight"; the roll-over point = front limit. Compare setups or tyre sets at the same track.
- Steering torque gradient: gated in quasi-steady cornering. A falling gradient while steering increases flags front saturation (understeer onset) objectively, independent of the driver's comment.
- Rack force estimate (hydraulic): with assist pressure sensors on both rack chambers, rack force = driver term + Δp·A. Rack force × steering-arm length ÷ total trail () approximates front-axle lateral force – a powerful front-grip estimate (see Level 3).
- Health channels: PAS fluid temperature and pressure, pump current, EPS motor temperature and current – detect overheating (assist derating) before the driver reports "steering got heavy".
Pitfalls
- Column torque includes steering-wheel inertia and friction: filter and gate on low steering velocity for steady-state analysis.
- Hydraulic assist has hysteresis; compare loading and unloading separately.
- Sensor offset drift: check the straight-line mean (should be near zero; a consistent offset can mean camber/caster asymmetry or crosswind).
Power steering & steering torque as a data channel: L3 Advanced explanation
Front-limit detection, quantitatively. Using the SAT physics: . In the linear region, grows proportional to . As the front approaches its limit, falls, so falls. Define:
(normalised by the low-g reference slope from the same run). ≈ 1 in the linear range, falling to 0.5–0.7 as the front saturates. Lap metrics such as "time with < 0.8" or average in mid-corner phases quantify front-limited running – complementary to the understeer angle, but independent of the steering-ratio and Ackermann calibration.
Reading with the understeer angle. only tells you whether is collapsing, i.e. how close the front tyres are to their peak.
- Positive understeer angle with ≈ 1: ordinary linear understeer. In the bicycle model with while , so stays at 1. This is the tyre slip balance (weight distribution, LLTD) plus any compliance and roll steer – not saturation.
- Understeer angle rising and falling together: front saturation.
Pitfalls
- Assisted cars: compute from rack force (driver term + , or EPS motor torque), never from column torque alone. With a rising boost curve, falls as rack force rises even with perfectly linear tyres, and column-torque would flag saturation that is not there.
- Downforce: vertical load lengthens the contact patch, so and SAT per g rise with speed. Build the linear reference slope in speed bands, not one slope for the whole lap.
Assist removal for analysis. For hydraulic systems with pressure sensors:
with the steering-arm length (moment about the kingpin per unit rack force). Since is unknown and varies, use it for relative comparisons (setups, tyre sets, stints) rather than absolute force.
Driver-effort engineering. On unassisted cars (F3, F2, IndyCar), steering effort is a physical limit over a race: a driver's precision deteriorates late in the race if RMS torque is high. Track RMS/peak torque per lap and over a race; compare against driver fitness data. Setup choices that raise front aero load or caster increase effort – sometimes a slightly less "optimal" setup is faster over the full race because the driver can keep precision.
Transient content. Spectral analysis of steering torque reveals kickback frequencies (kerbs, wheel-hop), and hydraulic assist instability (chatter ~10–30 Hz). Persistent steering-torque oscillation with low steering-angle motion is a sign of assist instability or worn rack mounts.
Key formulas
- c
- rack travel per rev (m/rev)
- driver steering torque (N·m)
- Δp
- assist pressure difference (Pa)
- rack piston area (m²)
- steering-arm length (m)
Trackside takeaways
The column torque sensor measures driver torque; on assisted cars rack force needs assist pressure or motor current too.
Steering torque vs lateral g rolls over as the front saturates – an objective understeer marker.
Steep assist curves numb the limit feel; assist level is a feel setting, not just comfort.
Monitor PAS temperatures and currents – assist derating looks like a sudden balance change to the driver.
On unassisted cars, track RMS steering effort as a race-performance factor.
On your car
Hydraulic or electro-hydraulic assist on most cars; some allow assist maps. Overheated PAS fluid in hot races is a known failure mode – log fluid temperature.
Check yourself
On a hydraulically assisted GT3, the logged column-torque sensor reads 8 N·m in a fast corner. Why can't you use this alone to estimate front lateral force?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 19 Steering Systems · power steering, steering torque and feel
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior · aligning torque vs slip angle
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.4 Driver Activities That Indicate Vehicle Balance · steering-angle-based balance indicators – compare with the torque-based ones here
- Segers – Analysis Techniques for Racecar Data Acquisition — §14.6 Steering · driver feels front grip through aligning-torque changes at the wheel