Understeer angle from data
Subtract the kinematic (Ackermann) steer angle the car would need at zero slip from the actual road-wheel angle: what remains is the understeer angle – a math channel and a lap statistic for tracking balance over runs, setups and stints.
Understeer angle from data: L1 Foundation explanation
The idea. At very low speed, a car following radius needs a road-wheel angle of only
(the kinematic or Ackermann steering angle – not to be confused with Ackermann geometry between the two front wheels). At speed, the front and rear tyres run slip angles. If the car needs more steer than , it is understeering; less, it is oversteering:
From data. is not measured, but in steady cornering :
so:
with in degrees, in m, in m/s², in m/s. Positive = understeer, negative = oversteer. Absolute values remove the left/right sign convention.
Worked example: GT3, L = 2.7 m, 150 km/h (41.7 m/s), 1.6 g (15.7 m/s²): rad = 1.40°. Logged steering 30° with ratio 13:1 → road wheel 2.31°. Understeer angle ≈ +0.9°.
How big is it? Segers' GT1 examples range from slightly negative to about 1.2° lap average, with race-stint values often only 0.2–0.5°. The value depends heavily on gating, ratio calibration and compliance, so the trend matters more than the absolute value.
Understeer angle from data: L2 Practitioner explanation
Building the channel (Segers' method)
- Road-wheel angle: measure the steering-wheel → outside-wheel map on turn plates and fit it (linear or polynomial). Math channel: .
- Kinematic angle: with speed in km/h and lateral acceleration in g:
- Understeer angle: .
- Gate it: only valid in quasi-steady cornering. Typical gates: V > 50–60 km/h (the term explodes at low speed), > 0.4–0.5 g, low steering velocity, and optionally brake < threshold / throttle within a band to split entry, mid, exit.
Using it
- Track map overlay: colour the understeer angle on the track map to spot which corners/phases are understeer- or oversteer-limited.
- Lap statistics: average understeer angle per lap, per stint. Segers shows a run where average understeer fell lap by lap (balance drifting towards oversteer as the tyres aged) and another where a driver's best laps came at low average understeer while his team-mate's came at higher values – evidence for different setup needs.
- Setup comparison: average understeer angle in mid-corner phase before/after a change, at similar track conditions.
- Phase gating: entry (brake on, steering increasing), mid (throttle low, |steer rate| small), exit (throttle rising) – reveals "entry understeer, exit oversteer" patterns.
Pitfalls
- Sensor offsets: a 0.02 g lateral offset or 1° steering zero error biases the channel; calibrate on straights (mean of both should be ~0).
- Banking and camber of the track: the accelerometer measures a component of gravity on banked corners; no longer equals . Prefer the yaw-rate version (Level 3) there.
- Compliance: the effective ratio is higher at load, so the channel reads high in high-load corners. Comparisons between setups remain valid; absolute values between cars do not.
- Non-linear range: the SAE-style definition of understeer/oversteer is strictly valid in the linear tyre range and steady state. Race cars live in the non-linear range – use it as a comparative tool.
Understeer angle from data: L3 Advanced explanation
Yaw-rate formulation. In steady state and , so the kinematic angle can also be written . With a yaw-rate gyro:
Advantages: far less affected by banking and accelerometer mounting angles – the body-fixed gyro reads , about 1 % low at 9° (Indianapolis) and ≈9 % low at 24° (Texas turns 3–4; turns 1–2 are 20° since 2017), against a gravity bias of (≈0.4 g at 24°) in the accelerometer version; correct with a bank-angle map if you need absolute values. Less sensitive at low speed ( instead of ). Disadvantages: in transients yaw rate lags steering, so the channel spikes positive on turn-in and negative on exits even for a neutral car – gate on steering velocity or compare the two versions.
Relation to understeer gradient. In the linear range:
so a scatter plot of vs (gated, steady state) has slope (deg/g at the road wheel) – the understeer gradient. For a race car the plot is linear at low g and curves upward (front-limited) or downward (rear-limited) near the limit. Comparing these curves between setups is more informative than a single average: two setups with the same lap-average understeer can have very different limit behaviour.
Separating contributions. only if steering compliance, roll steer and compliance steer are zero. In reality:
Use the steering-torque channel (, see power-steering lesson) or a sideslip sensor (optical / GPS dual-antenna) to separate tyre saturation from compliance and geometry. With a sideslip measurement at the CG, you can compute front and rear axle slip angles directly. In the convention used above (slip positive in the direction of the turn): and , so . Check your logger's sign conventions for and before trusting the result.
Statistics done right. Use distance- or time-weighted averages within gates, not raw sample means; track condition (grip factor), fuel and tyre age covary with balance – plot understeer vs tyre age across stints, and compare setups at matched tyre age. A 0.1° shift in average understeer angle is meaningful only if run-to-run noise (same setup, same tyres) is smaller – estimate it from repeated laps first.
Understeer angle from data: L4 Expert explanation
Limits of the method. The kinematic reference assumes a bicycle model in steady state. In the non-linear range, an "understeer angle" of 1° could arise from a front axle at its peak and a rear axle well below it, or from both axles at large slip angles with a 1° difference – very different handling states with the same channel value. The channel says nothing about margin.
Better approaches for expert analysis:
- Axle slip angles from a sideslip sensor compared with tyre-model peak slip angles: tells you which axle is at the limit.
- Yaw-moment method (RCVD Ch. 8): compute the yaw moment needed (I_z·dr/dt) vs available; requires good mass/inertia and tyre data but separates control from stability.
- Lap-sim correlation: run the same metric on simulated laps; differences between real and simulated understeer angle per corner identify where the vehicle model (compliance, tyre, aero map) is wrong.
Driver influence. The understeer angle depends on the line the driver chooses: a driver who turns in early and carries more steering mid-corner shows higher values without the car being different. Normalise by comparing the same driver, or use segments where lines converge. Segers' driver-versus-understeer plot is a reminder: the "best" balance is a property of the car–driver system, especially in endurance racing where a compromise must work for several drivers.
Key formulas
- L
- wheelbase (m)
- lateral acceleration (m/s²)
- V
- speed (m/s)
- lateral acceleration (g)
- V
- speed (km/h)
- outside road-wheel angle (deg)
- r
- yaw rate (rad/s)
Trackside takeaways
Understeer angle = road-wheel angle − L·ay/V²; positive = understeer.
Needs a measured steering-wheel → outside-wheel map; calibrate sensor zeros on straights.
Gate on speed, lateral g and steady state; split by corner phase.
Use it comparatively (setups, stints, drivers), not as an absolute number between cars.
Yaw-rate version is better on banked tracks; cross-check saturation with steering torque or sideslip.
On your car
Segers' examples are GT cars: average understeer-angle trends over a stint show the balance moving to oversteer as tyres age (often rear degradation in RWD cars). Use it to compare drivers in endurance line-ups.
Check yourself
L = 2.6 m, V = 108 km/h, lateral acceleration 1.5 g, outside road-wheel angle 3.3°. What is the understeer angle?
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.5 The Understeer Angle · kinematic steer angle, math channel, lap statistics
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.6 Vehicle Balance with a Yaw Rate Sensor
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 5 Simplified Steady-State Stability and Control · understeer gradient
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 19 Steering Systems