Limited-slip types: plate/ramp, viscous, Torsen, active
Plate-and-ramp (Salisbury) diffs lock in proportion to input torque plus a preload; viscous diffs respond to speed difference; Torsen gear diffs to torque ratio; active diffs to a controller. Each has a distinct signature on track.
Limited-slip types: plate/ramp, viscous, Torsen, active: L1 Foundation explanation
All limited-slip differentials (LSDs) add a locking torque that resists a speed difference between the wheels. They differ in what that locking depends on:
| Type | Locking depends on | Typical use |
|---|---|---|
| Plate / ramp (Salisbury) | input torque (via ramp angles) + preload spring | GT, prototypes, most formula cars, TCR |
| Viscous (VLSD) | speed difference between wheels (fluid shear) | road cars, older rally/touring, centre diffs |
| Torsen / helical (ATB) | torque ratio between wheels (gear friction), TBR ≈ 2–4 | road cars, some FWD racing |
| Active / e-diff | controller-commanded clutch pressure | road supercars, Ferrari Challenge (road-car E-Diff, not team-adjustable), F1 (driver-adjustable maps) |
| Spool | fully locked | karts (solid axle), some oval/drag applications |
Plate/ramp is the racing standard. A clutch pack (alternating plates splined to the diff case and to the side gears) sits on each side. The input torque arrives through cross-pins sitting in V-shaped ramps in pressure rings. Under torque the pins climb the ramps, pushing the pressure rings apart and squeezing the clutch packs. More torque → more clamping → more locking. Separate ramp angles on the two faces of the V give different behaviour in drive (power) and coast (engine braking / overrun). A spring stack gives preload — locking even at zero torque.
Viscous: shear of silicone fluid between plates; locking grows with speed difference, so it only works after a wheel has already started to spin, and fluid heating changes the characteristic ("hump" mode). Rare in modern circuit racing.
Torsen: worm/helical gear friction gives a fixed torque bias ratio. Weak point: if one wheel has zero grip (lifted inside wheel over a kerb), TBR × 0 = 0 — no torque to the other wheel either. Some versions add preload to soften this.
Active: a hydraulic clutch pack whose pressure is set by a controller from speed, lateral g, steering, throttle. Can provide different locking in entry, mid-corner and exit — the ideal, and therefore often restricted by regulations.
Limited-slip types: plate/ramp, viscous, Torsen, active: L2 Practitioner explanation
Practical signatures on track.
Plate/ramp:
- Locking ∝ torque: strong lock under full throttle in low gears, little at part throttle mid-corner (where preload dominates).
- Drive vs coast independently tunable via ramp angles: e.g. 40° drive / 60° coast (illustrative). A lower angle = more locking (see next lesson).
- Plate wear reduces preload over mileage → behaviour drifts. Measure breakaway torque routinely.
- Chatter/"clunk" at low speed in pit lane and tight hairpins is normal with high preload.
Viscous:
- Response lag: locking builds only with speed difference, so it "lets the wheel go" then catches it. Drivers feel delayed traction; the temperature sensitivity makes it inconsistent over a stint.
Torsen / ATB:
- No locking without torque and none if one wheel is unloaded — weakness over kerbs and on lifted wheels in FWD touring cars, and a reason TCR teams prefer plate LSDs.
- Smooth, no plates to wear, little maintenance.
Active:
- Entry, apex and exit locking can be set independently and even per corner (F1 drivers adjust "diff entry/mid/exit" on the wheel).
- Needs pressure sensing, a control strategy and fail-safe; banned or spec-limited in most of the categories in this academy (check rules). Many road-car-derived one-make or GT4 cars use sealed or spec passive mechanical LSDs (e.g. Porsche Carrera Cup, where the road 911 GT3 has an electronically controlled rear diff lock; Lamborghini Super Trofeo, mechanical LSD with capped preload). The exception in this academy is the Ferrari 296 Challenge, which keeps the road car's electronically controlled E-Diff (integrated with TC via the 6D sensor, not adjustable by teams): the driver's levers are the TC and ABS positions, so the engineer's job there is coaching their use, not changing hardware.
Choosing among options (when you can): plate/ramp offers the best tunability per corner phase for passive systems; preload + drive ramp + coast ramp + number of friction faces = four degrees of freedom. Most series restrict some of them — in GT3 often only preload is free, sometimes with a choice of homologated ramp sets.
Maintenance and checks: diff oil (often shared with gearbox) temperature; plate wear measurement; breakaway torque test at each rebuild and ideally each event (car on stands, one wheel held, torque wrench on the other — a few seconds of rotation to read the steady slip torque). Always note the test convention: with the gearbox in neutral the case turns freely and the reading is about half the left–right torque difference the diff can sustain (see next lesson).
Limited-slip types: plate/ramp, viscous, Torsen, active: L3 Advanced explanation
Mathematical characterisation.
- Plate/ramp: , with different in drive and coast. A piecewise-linear torque-sensing law with an offset.
- Viscous: with –1 and decreasing with fluid temperature. A speed-sensing damper between the wheels — it adds yaw damping proportional to the wheel speed difference. Shear torque vanishes as , so it never locks the axle (except in hump mode): in steady cornering it acts as a soft, speed-dependent coupling, not a spool.
- Torsen: — equivalently , a pure torque-sensing law without offset. TBR 3 corresponds to .
- Active: with commanded — any law the controller implements, within actuator bandwidth (≈ 10–30 Hz).
Equivalence. A plate diff with and zero preload is, in drive, equivalent to a Torsen with TBR 3. A Torsen also biases torque in coast, but with a ratio fixed by its gear geometry (often near-symmetric; some designs deliberately differ between drive and coast) and with little or no preload. The plate diff can set its coast locking independently of drive (separate ramp face) and add a tunable preload. That's why the plate type dominates circuit racing: the locking law can be shaped to the corner phase.
Why active diffs are so powerful. A passive diff's locking is a function of input torque, but the desired locking depends on corner phase: low on entry and apex for rotation (but enough for stability on the brakes), high on exit for traction, with a careful transition around the moment the inside wheel would start to spin. A controller with lateral g, steering and yaw-rate inputs can approximate this; a passive diff must compromise. Where actives are banned, engineers approximate phase-dependence by combining preload (dominant at low torque: mid-corner and light coast), coast ramp (entry under engine braking), and drive ramp (exit), plus engine-braking maps and TC.
Key formulas
Trackside takeaways
Plate/ramp: locking = preload + k × input torque; separate drive and coast ramps.
Viscous reacts to speed difference (lag, temperature-sensitive); Torsen to torque ratio (fails with a lifted wheel).
Active diffs give phase-specific locking — powerful and therefore mostly regulated out.
TBR 3 ≡ k = 0.5 in drive.
Measure breakaway (preload) torque routinely: plate wear makes the diff drift.
On your car
Plate/ramp LSD; preload adjustable (spring stack), ramp sets and plate count limited by homologation — often one or a few options.
Check yourself
A TCR car’s inside front wheel lifts over a kerb on exit, and drive to the other front wheel drops to almost zero for as long as the wheel is airborne. Which differential type most likely shows this behaviour?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking · limited-slip differentials, locking characteristics
- Other — Manufacturer LSD service documentation (e.g. Drexler, Hewland, Xtrac) · ramp angle and friction-face conventions vary by supplier – check the manual for your unit