Why a differential: the open diff and its inside-wheel limitation
In a corner the outside wheel must turn faster than the inside one. An open diff allows that by splitting torque equally — which caps total drive at twice what the weakest (inside) wheel can transmit.
Why a differential: the open diff and its inside-wheel limitation: L1 Foundation explanation
Kinematics. In a corner of radius (at the car's centreline) with track width , the outside wheel follows a radius and the inside . Their speed difference is
where is the yaw rate. Example: rear track 1.6 m, 50 m radius → 3.2 % speed difference; in a 15 m hairpin → 10.7 %. A solid axle (a spool) forces both wheels to the same speed, so one or both tyres must slip longitudinally to reconcile it — scrubbing tyres and creating a yaw moment that resists turning.
The open differential lets the wheels turn at different speeds. Its defining property: torque is split equally between left and right (ignoring internal friction), whatever their speeds:
See it on the bench. Below, a plate-type limited-slip differential is cut open. The crown wheel drives the carrier, the lit spider gears let the two half-shafts turn at different speeds, and the clutch packs (LSD mode) add a locking torque. The bars show each wheel's torque and its speed relative to the carrier; the chart shows how input torque is split.
Try it:
- Choose Open and tighten the corner from 150 m to 12 m: the speed bars split (inside wheel slower, outside faster, about 53 rpm apart) but the torque bars stay equal – 1200 / 1200 Nm at 2400 Nm input.
- Switch to Plate LSD: the slower inside wheel now gets more – 1715 / 685 Nm. The difference is the locking torque, 120 Nm preload + 0.38 × input torque.
- Lower the input torque: the split narrows, because the ramps clamp the plates harder only when more torque goes through.
Takeaway: an open diff always splits torque equally, so the wheel with less grip limits both. An LSD sends extra torque to the slower wheel – more traction on corner exit, at the cost of a yaw moment that resists the car turning.
The limitation. Each wheel can only transmit as much torque as its tyre can carry. In a corner, lateral load transfer unloads the inside rear — on a GT car at 1.5 g it can lose 50–70 % of its static load. Because the open diff always sends equal torque, the moment the inside wheel reaches its grip limit, the outside wheel cannot get any more either. Add more throttle and the inside wheel spins up (the open diff happily lets it), while the outside wheel — with plenty of load and grip — stays at the same torque.
Total drive force with an open diff is therefore
That is the classic inside-wheel spin out of slow corners (or, on a lifted wheel, zero drive). It is why almost every racing car uses a limited-slip differential (LSD): it lets the diff transfer extra torque to the slower, better-loaded wheel.
The cost of locking: the more the diff resists speed difference, the more it behaves like a spool — yaw resistance and understeer in some phases, sudden oversteer in others. Managing that trade-off is diff setup.
Why a differential: the open diff and its inside-wheel limitation: L2 Practitioner explanation
Seeing it in data. With both driven-wheel speeds logged (Segers §4.2 recommends it precisely to evaluate the diff):
- Compute (choose left/right per corner direction, or use the sign of ) and compare it with the kinematic expectation (or ).
- Inside-wheel spin = the inside wheel becoming faster than kinematics allows — often faster than the outside wheel. In Segers' La Source example, separate slip channels for each rear wheel show which wheel is at the limit.
- With an open diff, inside spin appears together with low longitudinal acceleration and (if fitted) TC intervention, because TC sees average driven-wheel speed rising.
Numbers for the limitation. GT3, 1300 kg, rear static load ≈ 3.6 kN per wheel. Exiting a slow corner at 1.2 g lateral, lateral load transfer on the rear axle ≈ 1.5–2 kN: inside rear ≈ 1.8 kN, outside ≈ 5.4 kN. With μ ≈ 1.5 and the tyre also producing lateral force, the inside rear may support only ≈ 1–1.5 kN of drive force. Open diff total ≈ 2–3 kN; the outside wheel alone could carry ≈ 4–5 kN. Most of the available traction is wasted.
FWD is worse. In a TCR car, longitudinal load transfer also unloads the front, so inside-front spin starts very early. Open diffs in FWD racing are rare; mechanical LSDs dominate, at the price of torque steer.
Why not just a spool? A spool gives maximum traction in a straight line and on a lifted wheel, but in a steady corner it imposes : the outside tyre is forced to under-rotate (negative slip, braking force) and the inside to over-rotate (drive force). That creates a moment opposing the turn — classic spool understeer (RCVD Ch. 20). Karts live with it by lifting the inside rear; racing cars use LSDs to get between the two extremes.
Brakes as a diff substitute. Applying the inside brake transfers torque through an open diff to the outside wheel (brake-based TC / "e-diff" in road cars). In racing this is generally banned or impractical (brake heat), so the mechanical LSD carries the job.
Why a differential: the open diff and its inside-wheel limitation: L3 Advanced explanation
Torque balance with internal friction. A real open diff has internal friction (gear mesh, thrust washers), giving a small torque bias ratio (TBR) ≈ 1.1–1.3. In general a diff with locking torque capacity obeys, when the wheels rotate at different speeds:
— torque goes to the slower wheel. When the wheels turn at the same speed (diff not slipping), the split is set by the tyres, with .
This "torque to the slower wheel" rule is the key to all diff yaw effects:
- In a corner on throttle with no wheelspin, the outside wheel is faster → an LSD sends extra torque to the inside wheel → a yaw moment that resists rotation (understeer).
- Once the inside wheel spins and becomes faster than the outside, extra torque goes to the outside wheel → a moment that promotes rotation (oversteer) and much higher total traction.
So an LSD does not have a fixed "understeer" or "oversteer" character; it switches sign depending on which wheel is faster. That transition — from outside-wheel-faster (push) to inside-wheel-faster (snap) — is exactly what drivers describe as "it pushed, then it snapped". In data it is the sign change of the measured (the locking index of the data lesson crossing 1), not merely a deviation of from : any diff that restrains the speed difference at all pulls below kinematics, long before the flip. Recognising the flip is the core skill of diff tuning.
Tyre-side view. At a given axle drive force , the split affects each tyre's combined-slip state. The lightly loaded inside tyre saturates first; loading it with more drive (LSD in the non-spinning state) can bring it to its limit early, after which the diff state flips. Optimal locking keeps both rear tyres near their combined limit simultaneously — which is impossible with a passive diff over all corner phases, and is why active diffs (where permitted) are so effective.
Key formulas
- t
- track width (m)
- R
- corner radius (m)
- yaw rate (rad/s)
Trackside takeaways
Outside wheel must turn faster: ΔV = t·yaw rate (≈ 3 % in a 50 m corner, > 10 % in a hairpin).
Open diff = equal torque: total drive = 2 × what the unloaded inside wheel can take.
A spool kills inside spin but resists rotation in steady cornering.
An LSD always sends extra torque to the SLOWER wheel — its yaw effect flips sign when the inside wheel starts to spin.
Log both driven-wheel speeds to see what the diff is doing.
On your car
Mechanical LSD (plate/ramp) with preload and limited ramp options; open diffs are never used.
Check yourself
With an open differential, the inside rear wheel can transmit at most 800 N of drive force on a corner exit; the outside could transmit 3000 N. What is the maximum total drive force?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking · differential types, spool vs open, yaw moments from drive
- Segers – Analysis Techniques for Racecar Data Acquisition — §4.2 Traction and Longitudinal Slip · separate driven-wheel slip channels to evaluate differential work