Learn / Suspension Geometry & Kinematics / Bump steer & roll steer
L1 · Foundation

Bump steer & roll steer

Toe that changes with wheel travel steers the car without the driver. Measuring it with a bump-steer gauge and shimming the track-rod end is a core workshop skill; using roll steer deliberately is a balance tool.

Bump steer & roll steer: L1 Foundation explanation

Bump steer is toe change as the wheel moves vertically. It happens when the track rod (front) or toe link (rear) does not swing on an arc that matches the wheel's motion: as the upright rises, the track rod pulls or pushes the steering arm and the wheel steers.

Roll steer is the same effect expressed per degree of body roll. In roll, the outside wheel goes into bump and the inside into droop, so bump steer on both sides adds up to a steer angle of the axle:

  • Front outside wheel toes out in bump → front axle steers out of the corner → roll understeer.
  • Rear outside wheel toes in in bump → rear axle steers in the same direction as the front wheels, increasing rear slip angle → roll understeer (stabilising).
  • The opposite signs give roll oversteer.

Units: toe change in degrees per mm of travel (or mm of toe per 25 mm of bump, measured over the rim). Good race geometry typically holds front bump steer below ~0.05° over ±25 mm around ride height, unless a deliberate amount is designed in.

What the driver feels:

  • Front bump steer → car darts over bumps and kerbs, steering wheel kicks, braking instability as the front dives (both wheels toe out/in together).
  • Rear bump steer → rear "steers itself" over bumps or under squat: a nervous, rear-steering sensation on exits.

Why it matters more than its size suggests: a 0.2° toe change on a rear tyre is a 0.2° change in that tyre's slip angle – with a GT3 rear tyre cornering stiffness of very roughly 1.5–2.5 kN/deg at moderate load (so ~3–5 kN/deg per axle), that is 300–500 N of unwanted lateral force appearing every time the car hits a bump.

Key formulas

Toe from bump-steer gauge
δ=arctan⁡dfront−drearLplate\delta = \arctan\frac{d_{front} - d_{rear}}{L_{plate}}
dfront,dreard_{front,} d_{rear}
dial readings (mm)
LplateL_{plate}
distance between dials (mm)
Shim sensitivity
dδdz≈Δhltr a [rad/mm]\frac{d\delta}{dz} \approx \frac{\Delta h}{l_{tr}\,a}\ \text{[rad/mm]}
Δh
shim height change (mm)
ltrl_{tr}
track-rod length (mm)
a
steering-arm length (mm)
Roll steer from bump steer
ε≈dδdz⋅t2\varepsilon \approx \frac{d\delta}{dz}\cdot\frac{t}{2}
ε
roll steer (rad/rad)
t
track (mm)
Effect on understeer gradient
ΔKus=(εf−εr) dϕday\Delta K_{us} = (\varepsilon_f - \varepsilon_r)\,\frac{d\phi}{da_y}
εf,εrε_{f,} ε_r
roll steer, positive = steers out of turn

Trackside takeaways

  • Straight bump-steer line → wrong track-rod angle → shim the outer end.

  • Curved line → wrong track-rod length → rack/inner pickup change.

  • Outside front toe-out in bump and outside rear toe-in in bump = roll understeer (stabilising).

  • Recheck bump steer after ride-height changes over ~5 mm or any front-end contact.

  • Dynamic toe = static toe + bump steer + compliance steer.

On your car

Track-rod outer shims are usually allowed and documented in the manual; ride-height changes of more than a few mm warrant a bump-steer check because GT3 racks are positioned for a nominal ride height.

Check yourself

Question 1 / 4L2 · Practitioner

A bump-steer plot (toe vs wheel travel) is a clean straight line with slope 0.004 °/mm. What is the trackside fix?

Further reading
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 17 Suspension Geometry · bump steer and roll steer
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 19 Steering Systems · track-rod geometry
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 5 Simplified Steady-State Stability and Control · roll steer contribution to understeer gradient