Learn / Suspension Geometry & Kinematics / Caster, kingpin inclination, scrub radius & mechanical trail
L1 · Foundation

Caster, kingpin inclination, scrub radius & mechanical trail

The steering axis geometry decides steering weight, self-centring, camber change with steer and the diagonal weight jacking that happens every time the driver turns the wheel.

Caster, kingpin inclination, scrub radius & mechanical trail: L1 Foundation explanation

Steering axis. The front wheel steers about a line through the upper and lower ball joints (or strut top and lower joint) – the kingpin axis. Its orientation is described by two angles and two offsets:

  • Caster angle – side-view tilt; top rearward = positive. Race cars ~5–10°.
  • Kingpin inclination (KPI / SAI) – front-view tilt; top inward. Race cars ~6–14° (larger on GT cars with big brakes inside the wheel).
  • Mechanical trail – side-view distance on the ground from where the axis hits the ground to the contact-patch centre (patch behind = positive). Typical 15–40 mm.
  • Scrub radius – front-view distance on the ground between axis intercept and contact-patch centre (patch outboard = positive). Race cars often +10 to +40 mm, because large brakes push the ball joints inboard.

Mechanical trail is the lever arm on which the tyre's lateral force acts around the steering axis. It produces self-centring and part of the steering weight:

tm≈R tan⁡(caster)−et_m \approx R\,\tan(\text{caster}) - e

where RR is tyre loaded radius and ee any hub (caster) offset. With R = 330 mm and 7° caster: about 40 mm before offset.

Caster also changes camber with steering. When the driver turns, the outside front wheel gains negative camber (roughly caster × steer angle in radians) and the inside wheel positive. With 8° caster and 15° road-wheel steer at a hairpin: about −2° extra on the outside tyre. That is why high caster helps slow-corner front grip.

Scrub radius is the lever arm for longitudinal forces acting at the contact patch: braking (outboard brakes) or bumps on one front wheel produce a steering torque. Large positive scrub = kickback over kerbs and tugging under braking on uneven grip. Torque steer on front-drive cars is a different lever: the drive force from a driveshaft acts at the wheel centre (the torque is reacted inboard), so what matters is the kingpin offset at hub height, plus unequal driveshaft angles – not the ground scrub radius.

Key formulas

Mechanical trail
tm≈Rl tan⁡c−et_m \approx R_l\,\tan c - e
RlR_l
loaded tyre radius (mm)
c
caster angle
e
hub/caster offset (mm)
Camber change with steer
Δγ≈−δsin⁡c+(1−cos⁡δ)sin⁡λ\Delta\gamma \approx -\delta\sin c + (1-\cos\delta)\sin\lambda
δ
road-wheel steer angle (rad)
λ
kingpin inclination
Steering-axis moment (per wheel)
Mkp≈Fy (tm+tp)+Fx rsM_{kp} \approx F_y\,(t_m + t_p) + F_x\,r_s
tpt_p
pneumatic trail
rsr_s
scrub radius
FxF_x
longitudinal force at the contact patch

Trackside takeaways

  • Caster → mechanical trail (steering weight) and negative camber on the outside wheel with steer.

  • Caster jacking loads the inside-front/outside-rear diagonal in proportion to steer angle.

  • KPI lifts the car symmetrically when steering (self-centring) and adds positive camber.

  • Positive scrub radius = kickback and brake tug; spacers change it.

  • Too much mechanical trail can mask the steering-torque drop that tells the driver the front is saturating.

On your car

Caster adjustment via shims/eccentrics is typical; steps of ~0.5–1° are noticeable. Large brakes force big KPI and positive scrub; wheel/spacer choices move the scrub radius.

Check yourself

Question 1 / 4L1 · Foundation

With positive caster, what happens to the camber of the outside front wheel as the driver steers into a slow corner?

Further reading
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 19 Steering Systems · kingpin geometry, trail, scrub, jacking
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 17 Suspension Geometry