Ride height & rake as geometry
Ride height is not just an aero number: it sets the operating point of every kinematic curve – roll centre, camber, bump steer, anti percentages. Static and dynamic ride height can differ by tens of millimetres.
Ride height & rake as geometry: L1 Foundation explanation
Definitions. Ride height (RH) is the distance from a defined reference point on the chassis (floor, plank, skid block, or a manufacturer-specified jacking point) to the ground. Rake is the difference between rear and front ride height, often quoted in mm or as an angle:
with the distance between the reference points (often the wheelbase). Example: front 55 mm, rear 80 mm, 2.7 m apart → 25 mm rake, 0.53°.
Static vs dynamic.
- Static RH is set in the garage on flat pads at a defined state: driver (or ballast), defined fuel load, set tyre pressures, settled suspension.
- Dynamic RH is what the car actually runs: reduced by aero load (GT3 ~10–20 mm at top speed; prototypes and formula cars ~15–30 mm), changed by pitch under braking/acceleration, raised slightly by tyre growth at speed, and raised as fuel burns off.
Why it is geometry, not only aero: all suspension curves are functions of wheel position. Lowering the car by 5 mm moves the operating point of:
- roll-centre height (often by 10–15 mm),
- static camber (camber gain × 5 mm),
- bump steer (you are now at a different point of the curve),
- anti-dive/anti-squat percentages,
- the gap to bump rubbers/packers (effective rate changes earlier).
So a "simple" ride-height change is in reality a whole family of changes – and after any change you must re-check camber and toe, because both move with ride height.
Typical static values (indicative, series rules govern): GT3 front ~50–70 mm, rear ~70–90 mm; F3 front ~15–25 mm, rear ~30–50 mm (measured at plank/skid reference); LMP2 governed by plank and minimum heights.
Ride height & rake as geometry: L2 Practitioner explanation
Measuring static ride height properly
- Setup pads levelled to within ~0.5 mm (laser-levelled patch). Without this, everything below is noise.
- Set car state: fuel load per procedure (or ballast equivalent), driver or driver ballast in seat, tyre pressures to the setup value (cold), steering straight.
- Settle: roll the car back and forth, bounce each end; release friction in rod ends/dampers.
- Measure at the defined reference points, both sides; average left/right or use per-corner if setting cross-weight at the same time.
- Order matters: ride height → camber → toe → corner weights → recheck ride height. Every adjustment interacts.
Tyre effects: a 0.1 bar change in pressure changes tyre loaded radius roughly 0.5–1 mm on slicks; switching from a worn to a new tyre changes radius by the tread depth lost. Always set ride height on the tyre type/state you will run, or apply a known correction.
Dynamic ride height from data
- Laser/ultrasonic RH sensors (front, rear, often left/right): direct, but noisy over kerbs and sensitive to sensor angle; correct for pitch and roll if not at the reference point.
- From damper pots: (MR in spring/wheel convention). Tyre deflection can be 5–10 mm under peak aero load – too large to ignore.
- Average dynamic RH in fast corners and minimum RH under braking are standard lap metrics.
Rake as a balance tool: on diffuser cars more rake usually moves aero balance forwards (front wing/splitter closer to ground, diffuser expansion larger) and increases total downforce up to a stall/seal limit. Mechanically, rake also changes front and rear geometry operating points – a rake change via the rear raises rear RC and alters rear camber, so the mechanical balance changes too.
Pitch gradient (Segers §9.7): plot pitch angle (from damper pots) vs longitudinal g to see how the platform moves under braking and acceleration; different slopes for braking and traction reveal anti-geometry and bump-rubber contact.
Ride height & rake as geometry: L3 Advanced explanation
Ride height as a state variable. For performance analysis treat front and rear RH as continuous inputs to every kinematic table. A kinematic model should be indexed by (front heave, rear heave, roll, steer) and evaluated along the lap: RC heights, camber and toe at each point. Comparing a slow and fast corner on an aero car can show the front RC 20 mm lower and the front tyres with 0.5° more negative camber in the fast corner – differences which no static setup sheet shows.
Speed-dependent geometry trade-offs. A softer front spring with a rising-rate rocker or bump rubber lets the front drop more at speed: good for aero (more front load, lower front RH) but at the cost of more RC drop (more roll), more camber gain, possibly toe change from bump steer curvature. Every aero-driven RH decision has a mechanical-geometry bill. A senior engineer checks: camber at max-downforce RH, toe at max-downforce RH, RC height at both slow and fast corner RH.
Measurement uncertainties. Laser RH sensors measure to the track surface, which has texture (±1–2 mm), and are affected by sensor angle in pitch/roll: at 1° pitch and 300 mm distance from the reference point, the error is ~5 mm. Damper-pot-based RH depends on MR accuracy and the tyre-deflection model. Best practice: fuse both – calibrate the tyre-rate term with laser data on straights at known speeds, then use damper-derived RH in corners where lasers are noisy.
Fuel and tyre drift over a stint. On a GT3 with ~100 L of fuel, burning 70 kg raises the rear by roughly 2 mm at typical GT3 rates (more on softer-sprung cars; remember the tyre deflects in series with the spring) and changes rake, shifting both aero balance and geometry. Always state the fuel load at which static RH is set – it decides whether the static value should sit above or below the target. Endurance engineers plan static RH so that the average stint RH is in the optimum window, not the start-of-stint value.
Key formulas
- rear / front ride height (mm)
- distance between measurement points (mm)
- damper compression from static (mm)
- MR
- damper/wheel motion ratio
- tyre vertical rate (N/mm)
- tyre growth with speed (mm)
- pitch angle (deg)
- longitudinal acceleration (g)
Trackside takeaways
A ride-height change moves every kinematic curve's operating point – recheck camber and toe.
Static RH needs level pads, defined fuel/driver/pressure state and settled suspension.
Dynamic RH differs from static by 10–30 mm on aero cars; tyre deflection is part of it.
Rake changes aero balance and mechanical geometry simultaneously.
Plan static RH for the stint-average condition, not the start of the stint.
On your car
Minimum ride heights are often specified by BoP/technical regulations and checked post-session at defined points. Rake is a key balance tool; the static-to-dynamic change is moderate (~10–20 mm).
Check yourself
Front RH 52 mm, rear RH 82 mm, measured 2700 mm apart. What is the rake angle?
- Segers – Analysis Techniques for Racecar Data Acquisition — §9.7 Pitch Gradient
- Segers – Analysis Techniques for Racecar Data Acquisition — §9.1 Measuring Suspension Roll Angle · suspension vs tyre components of body motion
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 17 Suspension Geometry
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 12 Chassis Set-up