Camber gain & camber compensation in roll
Body roll tilts the outside tyre towards positive camber; suspension geometry gains negative camber in bump to fight it. How much is recovered – and what it costs in heave – shapes static camber choice and tyre temperatures.
Camber gain & camber compensation in roll: L1 Foundation explanation
The problem. A tyre makes most lateral force when it sits roughly upright to slightly leaning into the corner under load (a race slick typically wants roughly −1° to −2.5° of dynamic camber on the loaded outside tyre, depending on construction). When the body rolls by , a wheel fixed rigidly to the body would also lean by – towards positive camber on the outside wheel, exactly the wrong way.
Static camber is the first fix: start the wheel at, say, −3.5°. Camber gain is the second: wishbones of unequal length (short upper, long lower) pull the top of the wheel inwards as the wheel rises, adding negative camber in bump.
Camber gain is usually quoted as degrees per mm of wheel travel, or degrees of camber change per degree of body roll. For a double wishbone it is set by the front-view swing-arm length (distance from the wheel to its instant centre):
FVSA 1500 mm → about 0.038 °/mm. 20 mm of bump → ~0.76° more negative.
Camber compensation is how much of the body roll the geometry gives back on the outside wheel. With track the outside wheel rises when the body rolls, so:
Track 1600 mm, FVSA 2000 mm → 40 %. With 1.5° of roll the outside wheel loses only 0.9° relative to the ground instead of 1.5°.
Typical roll per g: formula cars ~0.3–0.7 °/g, GT3 ~0.6–1.2 °/g, TCR/GT4 ~1–2 °/g. More roll → more camber the geometry must compensate → more static negative camber needed.
Camber gain & camber compensation in roll: L2 Practitioner explanation
Why not 100 % compensation? It needs FVSA = t/2, i.e. the front-view IC on the car centreline (the geometry of a centre-pivot swing axle). That gives perfect roll compensation – but in pure heave both wheels gain ≈57.3/(t/2) °/mm (≈0.07 °/mm on a 1600 mm track: 25 mm of aero compression = −1.8° extra on both tyres). The RC height then equals the IC height, so any IC height above ground brings strong jacking. Race geometry is a compromise: aero cars that move 20–30 mm in heave favour long FVSAs (little heave camber change, low compensation) and control roll with stiff springs/bars instead.
Practical consequence: static camber depends on roll stiffness. If you soften the ARB and the car rolls 0.3° more at 1.5 g, the outside wheel loses roughly ≈ 0.2° of ground camber. That may be enough to move the tyre out of its temperature spread target.
Reading tyre temperatures for camber (pyrometer, inner/middle/outer after a run):
- Slicks are commonly run with the inner shoulder ~5–10 °C hotter than the outer at the outside of the dominant corner direction; a much bigger spread suggests too much static negative camber for the roll/camber gain, a reversed spread too little.
- Tyre manufacturers often impose limits (e.g. maximum negative camber in GT series supplied by a single tyre maker). Know them before you chase temps.
- Read with tyre carcass probe, not surface IR, after the in-lap cool-down distortion is understood.
Measuring camber gain: camber gauge on the hub face (or digital inclinometer on a flat plate), spring removed, jack wheel through its travel in 10 mm steps. Plot camber vs wheel travel – slope and curvature. Do both sides; asymmetric shimming and bent wishbones show up here.
Other contributors to dynamic camber (often bigger than people expect):
- Tyre lateral deflection (carcass roll-over): a few tenths of a degree to over a degree of effective camber.
- Compliance camber – uprights, wishbones, bearings deflect under lateral load: ~0.05–0.15 °/kN on GT-type cars. At 6 kN outside-front lateral force that is 0.3–0.9° positive.
- Caster and KPI camber change with steer (see the steering-axis lesson): the outside front gains negative camber with steer through caster.
Camber gain & camber compensation in roll: L3 Advanced explanation
Kinematic derivation. For a double wishbone, the wheel rotates about its IC in front view. A wheel travel rotates the wheel plane by (in radians), with the lateral distance from the contact patch to the IC – identical to the FVSA. Inclination of the line to the IC introduces a small lateral scrub, , which is the same geometric ratio that sets the RC height.
Ground camber of the outside wheel in roll (sign: negative = top in):
with positive towards the outside. Non-linearity: on typical SLA geometries the IC moves outboard (towards the wheel) in bump, so shrinks and the camber gain per mm increases with bump – the camber-vs-travel curve steepens (becomes progressively more negative) in bump. A sound design target is a near-linear curve over the working range.
Inside wheel. In droop the inside wheel loses negative camber (geometry reverses) and the body roll tilts it into negative camber relative to ground. The inside tyre's camber therefore goes strongly negative relative to the ground – but it is lightly loaded, so its contribution is small except in long, low-g corners and on low-roll-stiffness cars like TCR.
Interaction with heave and aero. On an aero car, ride height falls with speed. If the geometry gains −0.04 °/mm and the front drops 20 mm from slow to fast corners, both front tyres arrive in fast corners with −0.8° more camber than in slow ones. The camber you choose statically is therefore a speed-weighted compromise; check camber at the dynamic ride height of the corners that matter most for lap time.
Data method. Estimate dynamic outside-wheel camber as a math channel: camber_dyn = static + roll(from damper pots)·(1 − comp) + heave travel·gain + Fy·compliance. Compare across corners with the tyre spread data – it is the only trackside way to see why the same camber gives good temps in slow corners and overheated inner shoulders in fast ones.
Key formulas
- FVSA
- front-view swing-arm length, mm
- t
- track width (mm)
- κ
- fraction of body roll recovered at the outside wheel
- φ
- body roll (deg)
- compliance camber (deg/kN)
- lateral force (kN)
Trackside takeaways
Body roll pushes the outside tyre towards positive camber; static camber and camber gain fight it.
Camber gain ≈ 57.3/FVSA deg per mm; compensation = t/(2·FVSA).
100 % roll compensation means huge camber change in heave – aero cars avoid it.
Softening roll stiffness costs dynamic camber; recheck tyre temps after big ARB changes.
Compliance camber (0.05–0.15 °/kN) can be as large as the kinematic gain.
On your car
Static front camber typically −3° to −4°, often capped by the tyre supplier's recommendation. GT3 roll gradients around 0.6–1.2 °/g make camber recovery a real factor in ARB choice.
Check yourself
A front suspension has a front-view swing-arm length of 1800 mm. Approximately what camber gain does it give in bump?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 17 Suspension Geometry · swing-arm length, camber change in roll and bump
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior · camber thrust and optimal camber
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 23 Compliances · compliance camber