Tyre degradation modelling and stint length
Measure how tyres perform over their life during practice long runs, separate degradation from fuel and driver effects, and use a simple model to choose stint lengths and the number of stops.
Tyre degradation modelling and stint length: L1 Foundation explanation
Tyres don't deliver constant performance. Over a stint the overall grip falls, and if one axle wears faster the balance changes. To plan a race you need to know (Segers §16.2.2):
- How many laps from new until the tyre reaches peak performance?
- In which lap is the highest grip recorded?
- From the peak, how fast does performance fall (seconds per lap)?
- What is the realistic maximum life before a "cliff"?
- Which way does the balance drift (understeer or oversteer)? Which axle wears most?
- What is the average lap time over the life of the set?
Typical life phases:
- Warm-up (1–3 laps): pressures and temperatures rise into the window.
- Peak (often lap 2–4 on slicks).
- Steady degradation: roughly linear loss from wear and heat cycles.
- Cliff: rapid loss when the tread is worn or the compound overheats permanently.
Get the data in practice. Run long stints on representative fuel loads, and log tyre mileage for every set used (including qualifying sets). Plot lap time and a grip metric against tyre laps: the best (lowest) lap-time envelope traces the degradation curve; scatter above it comes from fuel, traffic and driver.
Tyre degradation modelling and stint length: L2 Practitioner explanation
Separating effects. Over a stint three things change together: fuel burns (faster), tyres degrade (slower), the driver adapts. Segers' Dubai example: in a 3-hour GT race the first driver suffered understeer for the first ~30 % of the stint, set his fastest lap on lap 3, lost ~1.3 s over the first ten laps, then adapted and returned to near-best times, before losing significant time in the last quarter (after ~24 laps) as wear set in.
Model each lap as
Fuel-correct first (), then fit – usually linear: , optionally with a warm-up term and a cliff.
Typical degradation rates (fuel-corrected, dry): GT3 on a durable compound ~0.03–0.1 s/lap; junior single-seaters on softer Pirelli compounds 0.05–0.2 s/lap depending on track abrasiveness and temperature. Measure your own: they vary hugely with track temperature and setup.
Stint length decision factors:
- Fuel range (refuelling races) – often the binding limit in GT/prototype endurance.
- Tyre performance – when does staying out cost more than a stop?
- Regulations – maximum driver stint time, minimum drive time, tyre allocation, mandatory stops.
- Track position and traffic.
Double-stinting (two fuel stints on one tyre set) is standard in many endurance races when deg is low: it saves the tyre-change time and preserves the allocation. Check the fuel-corrected lap times of the second stint to confirm it pays.
Balance drift. Track average understeer angle per lap through stints: if the car drifts to understeer as fronts wear, a setup that starts slightly oversteery can give a better average stint. Tyre-pressure targets must be set for the hot stabilised condition, not lap 1.
Tyre degradation modelling and stint length: L3 Advanced explanation
How many stops? A first-order model. Let the race be laps, degradation linear at s/lap per lap of tyre age, and pit loss seconds. With equal stints, the tyre time lost per stint is about with , so total time is
Setting :
Example: = 60, = 0.05 s/lap², = 22 s → → a one-stop (two stints). Check neighbours: 1 stint 90 s; 2 stints 45 + 22 = 67 s; 3 stints 30 + 44 = 74 s. The optimum is often flat – small differences between strategies – so track position, traffic and SC risk decide.
Refinements:
- Warm-up/out-lap penalty – add a fixed cost per new set (cold tyres, 1–3 s for hard compounds in cool conditions).
- Non-linear degradation – thermal deg can be partly recoverable (driver manages temperatures), wear deg is not; a cliff sets a hard maximum.
- Compound offset – a softer compound may be 0.5–1.0 s faster on fresh tyres but degrade faster. With offset and degradation rates , the soft is slower per lap after laps, but it banked time early, so over a whole stint from new it stays the faster choice up to laps (linear deg, equal warm-up). Do not confuse the two crossovers.
- Fuel interaction – heavy-fuel laps are slow anyway and load tyres more; deg often looks worse early in a stint.
- Track evolution – rubber laid down improves times by 0.01–0.05 s/lap in early race laps, masking degradation; compare against cars on different strategies to separate.
Using practice data well. Practice long runs rarely have race fuel and race conditions. Normalise: fuel-correct, temperature-correct (track temperature sensitivity of degradation), and compare tyre-life curves from several sets (lower envelope of lap time vs tyre mileage, as Segers shows). Keep a database across events – degradation per track and compound is one of the most valuable strategic assets a team has.
Tyre degradation modelling and stint length: L4 Expert explanation
From models to decisions under uncertainty. Real strategy tools run Monte Carlo simulations of the race: each car's pace, degradation and pit loss with uncertainty, overtaking models (a car needs a pace advantage of ~0.5–1.5 s/lap to pass depending on the track), and stochastic safety cars. The output is a distribution of finishing positions per strategy, not a single answer.
Key sensitivities to keep in mind:
- Degradation uncertainty dominates early-weekend strategy; update continuously from race laps (yours and rivals') with a Bayesian-style approach – weight new laps more as they accumulate.
- Thermal management interacts with driving: telling a driver to manage tyres (lower slip, smoother inputs) can reduce at a lap-time cost; this is effectively choosing a point on a pace–degradation curve. The optimum push level depends on stint length remaining: push when few laps remain, manage early in a long stint.
- Allocation constraints (limited sets per weekend) mean practice and qualifying use must be planned backwards from the race needs.
Key formulas
- d
- degradation rate (s/lap per lap of tyre age)
- tyre age (laps)
- L
- race laps
- S
- number of stints
- P
- pit loss (s)
Trackside takeaways
Fuel-correct lap times before judging degradation.
Log tyre mileage for every set; plot the lower envelope of lap time vs tyre laps.
Optimum stints ≈ L·√(d/2P); the optimum is often flat, so track position and SC risk decide.
Double-stinting pays when fuel-corrected second-stint times stay close to the first.
Track balance drift through stints; design setup for the average stint, not lap 1.
On your car
Durable compounds and refuelling make fuel range the usual stint limiter; double/triple stints on tyres are common in 24h races when track temperature allows.
Check yourself
Race: 50 laps, degradation 0.08 s/lap², pit loss 25 s. Using the linear model, what is the optimum number of stints?
- Segers – Analysis Techniques for Racecar Data Acquisition — §16.2 Lap Time Variation During a Race (§16.2.2 Tire Wear)
- Segers – Analysis Techniques for Racecar Data Acquisition — §2.2.5 Run Charts
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior