Reading tyre temperatures: probes, IR sensors and math channels
Inner/middle/outer temperatures tell you about camber, pressure and which tyre is working hardest. On-car IR adds corner-by-corner detail and lets you build objective channels: spread, pressure index, workload share and time-in-window.
Reading tyre temperatures: probes, IR sensors and math channels: L1 Foundation explanation
Tyre temperature is the most accessible measure of how hard and how evenly each tyre is being worked. There are two ways to measure it:
- Needle probe (pyrometer) in the pit lane. Three readings across each tread: inner, middle, outer, taken a couple of centimetres in from the shoulders and at the centre, with the needle a few mm into the rubber. This measures bulk tread temperature, which changes slowly, so it is a lap-average picture.
- On-car infrared (IR) sensors. One to three (or more, up to 8–16 channel arrays) per wheel, pointed at the tread. They read surface temperature continuously and show it corner by corner.
The classic interpretations (for a probe set):
| Pattern | Usual meaning |
|---|---|
| Inner hotter than outer by ~5–10 °C | Camber in a sensible range |
| Inner ≫ outer (15+ °C) | Too much negative camber (or too much toe) |
| Outer ≥ inner | Not enough camber |
| Middle hotter than shoulder average | Pressure too high (crowned patch) |
| Middle cooler than shoulder average | Pressure too low (shoulders carry load) |
| Whole axle hot vs other axle | That axle is doing more work (or sliding more) |
| Left side hot vs right | Track direction bias (more corners one way) |
Probe procedure matters. Read the most important tyres first, the same order every time, as quickly as possible (temperatures fall by several °C per minute). Note the pit-lane length and last corner, because both shape what you read. A slow in-lap destroys the information, so ask for a quick in-lap when you want temperatures.
Reading tyre temperatures: probes, IR sensors and math channels: L2 Practitioner explanation
On-car IR in practice.
- Mounting. Sensor distance and lens angle set the spot size. Aim so the spot stays on the same tread band through bump and droop. Fronts ideally move with steer (upright mounting) or you lose the patch at full lock. Validate with a hand IR gun in the garage.
- What surface temperature shows. It reacts to sliding within a fraction of a second: spikes on braking (fronts), in long corners on the outside tyres, and on exit wheelspin (rears). Segers §8.4 traces a rear tyre through a corner: cooling on the straight, little rise under braking (the rear is unloaded and speed is falling, so stays small), then a sharp rise as lateral force and slip build to the apex. Front tyres, by contrast, show clear surface spikes in heavy braking.
Segers' math channels (Ch. 8) that every engineer should build:
- Spread per wheel, lap-averaged and gated by corner direction, for camber.
- Pressure index : positive means pressure high, negative means low. Averaging the shoulders removes the camber effect.
- Workload share: which tyre is doing the most work. Segers' version divides each tyre temperature by the sum of all four. A share of Celsius values depends on the arbitrary zero of the scale and compresses differences (one tyre at 100 °C with three at 70 °C shows only 32%), so a better version uses the rise above track temperature: . The tyre-energy metric (degradation lesson, L4) is better still. Run-chart it across a stint.
- Time-in-window per tyre: percentage of lap time below, inside and above the working window.
- Axle inside/outside difference and against lateral G: a proxy for relative lateral load transfer per axle. A harder front ARB gives a bigger front difference.
Diagnosing balance with temperatures (Segers §8.6). If the car understeers mid-corner and the outside front spikes above the window while the inside front stays cold, the front pair is suffering from too much load transfer and an overheated outside tyre. Softer front roll stiffness is a candidate fix. If the front axle average is fine but the inside/outside difference is extreme, it is a distribution problem, not a compound problem.
Reading tyre temperatures: probes, IR sensors and math channels: L3 Advanced explanation
Surface vs bulk vs carcass. Pit probes and surface IR answer different questions. Surface temperature is dominated by instantaneous sliding power and cools within a second on a straight. Bulk temperature integrates over laps and determines compound modulus and grip potential. A tyre with a high surface but normal bulk temperature is sliding too much (overdriven, wrong balance). High bulk with a modest surface means carcass/hysteresis heating: low pressure, high deflection, soft vertical spring, or brake heat soak.
Why one probe set can mislead.
- The last two or three corners before pit entry dominate the surface and outer bulk layers.
- Probe depth variation (±2 mm) changes the reading by several °C on a tyre with steep gradients.
- Ambient and pit-lane time vary between runs. Normalise by comparing differences (spread, pressure index), not absolute values.
- Worn tyres have less rubber over the carcass, so readings are closer to carcass temperature.
Using IR quantitatively.
- Gated statistics: lap-average spread only when g, separated by outside/inside. Segers' Table 8.2 approach of a corner-by-corner camber evaluation gives a matrix of "too much / OK / not enough" per wheel per corner. Static camber is then a weighted decision over the corners that matter for lap time.
- Thermal model fit: fit heating and cooling coefficients from IR traces in a single-node model ( = heating − cooling to air − cooling to track). It lets you predict temperatures for a new driver style, a hotter track or a different fuel load.
- Workload vs load transfer: plot front and rear inside/outside temperature difference against calculated front and rear lateral load transfer. The slope changes with ARB and pressure changes (Segers §8.6, Figs. 8.21–8.23), giving an objective "did the change do what we wanted" check.
Reading tyre temperatures: probes, IR sensors and math channels: L4 Expert explanation
Limitations at expert level.
- Emissivity and reflections. IR sensors assume an emissivity (~0.95 for rubber). Marbles, wet surfaces and sun reflection on rubber can shift readings by several degrees. Wet running makes IR nearly meaningless for compound temperature.
- Spatial aliasing. A three-point IR array samples three narrow bands. A hot band from camber and a hot band from a pressure crown can look identical with only three points. Multi-channel arrays (8–16 points) reveal the actual profile shape and are standard in top categories.
- Temperature is an effect, not a target. The objective is lap time and stint performance. A setup that cools the outside front may cost front grip by reducing the slip angle the driver can use. Always correlate temperature changes with balance metrics (understeer angle, yaw-rate error) and lap time.
- Tyre models with thermal states (multi-node: surface, bulk, carcass, gas) are now standard in top-level simulation. Your IR and TPMS data are the correlation targets. A simulation that matches lateral force but not temperature evolution will mis-predict long-run balance drift.
Cross-check rule: if pit probe, on-car IR and TPMS gas temperature tell three different stories, trust the trend in each and investigate sensor installation first. Changing setup on contradictory data is how teams lose a test day.
Key formulas
- > 0: pressure too high; < 0: too low
- tyre temperature (°C)
- track surface temperature (°C)
Trackside takeaways
Probe = bulk (lap-average); IR = surface (corner by corner). They answer different questions.
Inner hotter by ~5–10 °C: sensible camber. Middle vs shoulder average: pressure.
Take probe readings fast, in a fixed order, after a quick in-lap, and note the last corners and pit-lane length.
Build spread, pressure-index, workload-share and time-in-window channels and run-chart them.
An outside tyre spiking out of the window while the inside stays cold points to a load-transfer distribution problem.
On your car
Most teams run at least single-point IR per wheel, and many run multi-point. With no tyre warmers, time-in-window over the first laps of a stint is a key comparison between drivers and setups.
Check yourself
Probe readings on a rear tyre: inner 92 °C, middle 99 °C, outer 88 °C. What does the middle reading suggest?
- Segers – Analysis Techniques for Racecar Data Acquisition — §8.3 Working with Infrared Tire Temperature Sensors
- Segers – Analysis Techniques for Racecar Data Acquisition — §8.6 Lateral Load Transfer and Tire Temperature
- Segers – Analysis Techniques for Racecar Data Acquisition — §8.7 Tire Workload Distribution
- Segers – Analysis Techniques for Racecar Data Acquisition — §8.8 Camber Evaluation with Tire Temperature Sensors
- Segers – Analysis Techniques for Racecar Data Acquisition — §8.9 Tire Pressure Evaluation with Tire Temperature Sensors