Steering ratio: steering-wheel angle vs road-wheel angle
The logged steering channel measures the steering wheel, not the tyres. Knowing the true, non-linear and compliant relationship to road-wheel angle is the basis of every steering-related math channel.
Steering ratio: steering-wheel angle vs road-wheel angle: L1 Foundation explanation
Overall steering ratio = steering-wheel angle / road-wheel angle:
For a rack-and-pinion system with rack travel per steering-wheel revolution (the "C-factor", mm/rev) and steering-arm length :
Example: = 120 mm, = 60 mm/rev → SR ≈ 12.6:1. 90° at the steering wheel → ~7° at the road wheels.
Typical ratios (indicative)
| Car | Overall ratio | Comment |
|---|---|---|
| Road car | 14–17:1 | comfort, low effort |
| GT3 / GT4 | ~11–15:1 | power assisted |
| TCR | ~12–15:1 | road-derived rack, assisted |
| Formula (F4–F2) | ~8–12:1 | unassisted, very little lock |
| Prototype | ~9–13:1 | assisted |
What ratio choice changes
- Quicker (lower) ratio: less hand movement, faster corrections – but more steering effort (torque at the wheel scales with 1/SR) and a twitchier feel around centre.
- Slower (higher) ratio: lighter, calmer, but more hand movement – at tight hairpins the driver may run out of comfortable hand position (hand-over-hand is unacceptable with a race wheel full of buttons).
Important: the steering-angle sensor on the column measures steering-wheel angle. To get what the tyres actually do you need the road-wheel angle – via the ratio, which you must measure on your car.
Steering ratio: steering-wheel angle vs road-wheel angle: L2 Practitioner explanation
Measuring the ratio (Segers' method)
- Car on turn plates (or laser alignment) at ride height with load, wheels straight.
- Steer in steps (e.g. 10° or 20° at the steering wheel, read from the logged steering channel itself, not a protractor) both directions to full lock.
- Record outside wheel angle for each direction (left wheel for right turns, etc.).
- Fit a curve: road-wheel angle = f(steering angle). Often near-linear for small angles; polynomial if the rack/arm geometry is non-linear.
- Put that function in the logger as a math channel – it is the basis for understeer angle and Ackermann-based analysis.
Why the outside wheel: it is the more loaded wheel and the one that dominates the axle's lateral force; it is also the convention Segers uses for the understeer angle. Note that with Ackermann, the inside wheel angle is larger – using the average (or inside) gives a different "ratio".
Non-linearities you will find
- Ackermann makes inside and outside ratios diverge with steer.
- Steering-arm/track-rod angles: the ratio changes with lock (often quicker at larger angles on race geometry).
- Variable-ratio racks on some road-derived cars (TCR, GT4).
- Bump steer: the wheel angle at a given steering-wheel angle changes with ride height.
Compliance – the on-track ratio is not the static one. Under aligning torque the column, U-joints, rack mounts and track rods twist. The driver must add steering-wheel angle to get the same road-wheel angle: the effective ratio rises with load. On an unassisted formula car this can be several degrees of steering wheel at the limit; on assisted cars the column twist is reduced but rack-mount compliance remains.
Calibration pitfalls
- Steering sensor zero drifts after a steering-wheel removal or column work: recalibrate on the alignment pad, and check in data – the straight-line steering average should be ~0 (or a small, consistent offset from crosswind/camber).
- Toe changes also offset the zero relationship.
- Swapping the steering rack (spares) can change the C-factor: check part numbers and remeasure.
Steering ratio: steering-wheel angle vs road-wheel angle: L3 Advanced explanation
Choosing a ratio as an engineer. The ratio sets two driver-relevant gains:
- Yaw-rate gain per steering-wheel degree: (linear bicycle model, = understeer gradient in rad/g). At high speed this falls; quick racks keep the car responsive at high speed but make it nervous on straights.
- Torque gain: steering-wheel torque ≈ kingpin moment / (SR·η) minus assist. Changing ratio from 12 to 10:1 raises effort by 20 % on an unassisted car.
Ratio and driver workload in data. Because , steering-wheel velocity and acceleration (deg/s, deg/s²) scale with SR for the same road-wheel motion. On a quicker rack (lower SR) a driver looks smoother in the steering-wheel channels without being any smoother at the tyres; on a slower rack the same tyre inputs show as bigger, faster hand movements. Convert to road-wheel angle (divide by SR, or use the measured map) before comparing steering-speed channels or their lap averages across cars, drivers on different racks, or rack changes (Segers §14.6 builds the steering-speed smoothness channel; the ratio correction is our addition).
Kinematic vs effective ratio from data. You can estimate the effective on-track ratio by regression: in steady, low-g corners (where tyre slip and compliance are small), road-wheel angle ≈ + small understeer; plotting against for gated low-g data gives a slope ≈ SR (plus understeer gradient contribution). Divergence at higher g mixes compliance and understeer – which is exactly why understeer-angle channels on high-compliance cars read high.
Steering ratio in simulators. Drivers adapt to ratio quickly but sim correlation requires the column compliance and assist model; otherwise the sim car feels too direct and drivers over-steer the real car in the first laps after a rack change.
Key formulas
- a
- effective steering-arm length (mm)
- c
- rack travel per steering-wheel revolution (mm/rev)
- moment about each kingpin (N·m)
- η
- steering efficiency
Trackside takeaways
The steering channel is the steering wheel – convert to road-wheel angle with a measured map.
Measure on turn plates, outside wheel, both directions, fit a function, use it as a math channel.
Quicker ratio = less hand movement but more effort and twitchier centre feel.
Compliance makes the effective on-track ratio higher than the static one.
Steering-wheel velocity scales with SR: convert to road-wheel angle before comparing drivers or rack changes.
On your car
Unassisted with a quick ratio: effort is high and column compliance is noticeable in fast corners. Driver fitness and steering weight complaints are common.
Check yourself
Rack C-factor 75 mm/rev, effective steering-arm length 135 mm. The driver applies 120° of steering-wheel angle near straight-ahead. Approximate road-wheel angle?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 19 Steering Systems · overall ratio, steering compliance
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 23 Compliances
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.5 The Understeer Angle · measuring steering-wheel vs wheel angle on turn plates