Lock-up diagnosis: front vs rear, wheel speed vs reference speed
Detect and classify lock-ups from wheel speeds against a reliable vehicle reference speed, then separate bias, technique, platform and powertrain causes.
Lock-up diagnosis: front vs rear, wheel speed vs reference speed: L1 Foundation explanation
A lock-up occurs when a wheel's rotational speed collapses towards zero while the car is still moving: the tyre's slip ratio goes far beyond its optimum (~8–15 % for slicks), braking force falls, lateral grip almost disappears and the tyre can be flat-spotted within a fraction of a second, causing vibration for the rest of the stint.
Slip ratio:
Under braking ; a fully locked wheel has .
How it shows in the data (Segers §5.4): the wheel-speed trace of the locking wheel drops almost vertically below the vehicle speed, then jumps back up when the driver releases pressure. Plot all four wheel speeds against a reference speed (GPS), or a slip-ratio channel per wheel.
Which wheel locks? Usually the one with the least load on the axle with the most brake relative to its grip:
- Inside front during trail braking (lateral transfer unloads it).
- Both fronts in a straight line with too much front bias or a too aggressive initial stamp.
- Rears with too much rear bias, over a crest, or when engine braking adds to rear brake torque on downshifts.
Front vs rear consequences:
- Front lock: the car goes straight on (no steering response) — safe but costly; flat-spotted fronts.
- Rear lock: the rear loses lateral grip, the car rotates — can spin. Driver feedback is often "the rear stepped out on entry" rather than "rear lock".
Typical driver comments: "locking the inside front into T1" (bias, technique, or front geometry/diff), "the rear locks on the downshift" (engine braking / downshift / diff), "locks over the bump" (platform).
Lock-up diagnosis: front vs rear, wheel speed vs reference speed: L2 Practitioner explanation
Getting a good reference speed. Under braking every wheel is braked, so no wheel represents true speed. Options:
- GPS speed (Doppler, 10–25 Hz, good to ~0.1–0.2 km/h): the best general reference.
- Integrated longitudinal acceleration seeded with the speed at brake application: good for 1–2 s, drifts after that.
- Fastest wheel: usable without GPS, but fails when all wheels are slipping (heavy braking on a slippery surface).
Calibrate rolling radius. Wheel speed = , and changes with tyre size, wear, pressure, load and speed (growth at high speed). Calibrate each wheel against GPS on a constant-speed straight; otherwise you will see apparent slip of ±2–3 % that isn't real.
Lock-up channel. Define per wheel and flag lock-ups when (–20 %) for more than ~50 ms. Count per corner per lap. Run charts per corner show which zones are a problem and whether changes help.
Diagnosis matrix:
| Pattern | Likely cause | First actions |
|---|---|---|
| Both fronts, early in zone, every lap | Bias too far forward or stamp too aggressive for the platform | Bias rearward 0.5–1 %, check front damping/pitch |
| Fronts late in zone (low speed) | Pressure not reduced as downforce fades | Driver: progressive release; migration; bias |
| Inside front at turn-in | Trail-braking load on unloaded wheel | Bias, release technique, front ARB/diff entry, toe/camber |
| Rears, high-speed zones | Rear-biased bias with front-heavy aero under pitch, or crest | Bias forward, platform |
| Rears, at downshifts | Engine braking / downshift timing / diff | Engine-braking map, blip, diff coast ramp |
| One wheel, one location | Bump/kerb unloading | Damping, line, local only |
| All wheels, wet | Low μ, bias too far forward, pressure too high | Bias rearward, driver |
Late-zone front locks on aero cars are very common: at the start of the zone downforce supports high pressure; as speed falls, the tyres lose load but the driver keeps the pressure. The fix is mainly technique (progressive release), sometimes migration or more rearward bias.
Misconception: "a lock-up means the bias is wrong." Many lock-ups are technique (release), platform (bumps) or powertrain (downshifts). Change bias only when lock-ups are systematic on one axle across corners.
Lock-up diagnosis: front vs rear, wheel speed vs reference speed: L3 Advanced explanation
Precise slip estimation. For quantitative work (tyre peak-slip identification, ABS tuning), the reference speed must be at the wheel location: in a corner, each wheel's ground speed differs by yaw rate × lateral offset: (track width ). At 30 °/s yaw rate and 1.6 m track this is ±0.42 m/s — 1.5 % slip at 100 km/h, enough to corrupt inside/outside comparisons. Correct for it before concluding the inside front is "slipping more".
Brake torque balance at a wheel. Wheel rotational dynamics (same convention as the formula card, positive when driving): . Under braking , so is the tyre torque spinning the wheel back up against (and against engine braking, a negative ). At the onset of lock, passes its peak and falls, so diverges: the "knee" in the wheel-speed trace marks the tyre's peak slip. Using and line pressure (→ ), you can estimate at each instant — a poor man's tyre longitudinal curve per axle, useful for checking whether the bias puts both axles near their peak slip.
Coupling with the platform. On a stiff aero car, front ride height under braking drops; if the front hits packers/bump rubbers abruptly, the contact-patch load fluctuates at the tyre-hop frequency (~15–20 Hz) and a wheel can lock momentarily at each unload. Signature: lock spikes synchronised with RH minima or damper velocity peaks. Fix: packer gap, bump-rubber rate, front high-speed bump damping — not bias.
Diff and lock-ups. With a locking diff on overrun (high coast ramp/preload), the rear wheels are coupled: the clutch friction moves braking torque from the slower inside rear to the faster outside rear, so the inside rear rarely locks on its own and the axle gives a stabilising yaw moment — but if total overrun torque is too high both rears let go together, abruptly. With an open-ish diff the engine braking is split equally, and the lightly loaded inside rear can lock on its own. Correlate rear lock events with throttle = 0, gear changes and diff settings (see the entry-stability lesson).
Flat-spot severity. Energy dissipated in the contact patch during a lock is roughly : a 3 kN front axle force at 40 m/s for 0.3 s is 36 kJ concentrated on one patch — enough to remove a millimetre-scale layer of tread on a slick. Short locks at high speed are worse than long locks at low speed. A vibration complaint after a lock can be confirmed with a wheel-speed or vertical-acceleration FFT at the wheel rotation frequency ().
Key formulas
- wheel angular speed (rad/s)
- dynamic rolling radius (m)
- V
- reference ground speed at the wheel (m/s)
- wheel+brake inertia (kg·m²)
- tyre longitudinal force, positive driving (N)
- r
- yaw rate (rad/s)
- t
- track width (m)
Trackside takeaways
Lock-up = wheel speed collapsing below reference speed; slip ratio approaching −1.
Use GPS as reference speed and calibrate rolling radii against it on a straight.
The wheel with least load on the most-braked axle locks first — usually the inside front on trail braking.
Front lock: car goes straight (safe). Rear lock: car rotates (dangerous) — drivers often report it as oversteer.
Late-zone front locks on aero cars = pressure not released as downforce fades.
Lock spikes synchronised with ride-height minima = platform problem, not bias.
On your car
The 992.1 Porsche 911 GT3 Cup has no ABS: lock-up diagnosis and bias work are central, and flat spots can end a race. ABS-equipped Cup cars (the 2026 992.2 911 Cup with Bosch M5 ABS, Ferrari Challenge, Super Trofeo) shift the problem to ABS activity analysis.
Check yourself
During trail braking into a right-hander, which wheel is most likely to lock first (assuming normal front-biased brakes)?
- Segers – Analysis Techniques for Racecar Data Acquisition — §5.4 Lock-up
- Segers – Analysis Techniques for Racecar Data Acquisition — Ch. 4 (longitudinal slip ratio)
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior (longitudinal slip)
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 20 Driving and Braking