Low-speed vs high-speed damping: body vs wheel
"Low" and "high" speed refer to damper shaft velocity, not car speed. Low-speed damping controls body motion from driver inputs and aero; high-speed damping controls the wheel over bumps and kerbs.
Low-speed vs high-speed damping: body vs wheel: L1 Foundation explanation
Shaft speed, not car speed
"High-speed damping" does not mean damping at high car speed. It means damping at high shaft velocity – fast suspension movements from bumps and kerbs, which happen at any car speed.
Segers' practical ranges:
| Shaft velocity | Dominated by | What it controls |
|---|---|---|
| < 5 mm/s | friction (seals, spherical bearings) | nothing tunable – just keep friction low |
| 5–25 mm/s | body motion: roll, pitch, heave from braking, cornering, throttle | transient balance, platform, driver feel |
| 25–200 mm/s | road input: bumps, ripples | tyre contact, mechanical grip over bumps |
| > 200 mm/s | kerbs, big hits | kerb riding, stability, travel |
The boundary ("knee") is car-specific: ~20–30 mm/s on stiff high-downforce formula cars, ~40–75 mm/s on heavier GT/touring cars whose body moves faster.
Low-speed (LS) = how quickly the car settles into roll and pitch when the driver brakes, turns and accelerates. The driver feels this directly: response, support, "connected" vs "lazy".
High-speed (HS) = how the wheel follows a bumpy surface. Too much: the tyre skips over bumps, the car "crashes" and loses grip. Too little: the wheel bounces after a bump and the body gets unsettled. Drivers often describe HS problems vaguely ("no grip over the bumps", "harsh") – data is essential here.
Low-speed vs high-speed damping: body vs wheel: L2 Practitioner explanation
Diagnosing which range to work in
Step 1 – identify the phase and the motion. Use damper velocity channels (derivative of filtered pot position) and look at the event: entry (pitch + roll building), mid (body steady), exit (roll unwinding + squat). Segers recommends a direction channel: low-pass filter position to remove the high-speed content, then differentiate – positive = bump, negative = rebound – and colour it on the track map per corner. (The cutoff is your choice; ~5–8 Hz with a 2nd-order or higher filter is common: it keeps the 2–5 Hz body modes and rejects 12–20 Hz wheel hop, at the cost of some phase lag near 5 Hz.) You then see which corner is in LS bump or LS rebound when the problem occurs.
Step 2 – check velocity magnitudes. If the complaint is in an area where velocities are < ~25–50 mm/s, it's an LS (body) issue. If spikes > 100 mm/s coincide with the problem (bumps on entry, a kerb at apex), it's HS.
Step 3 – change the right adjuster.
- Entry instability over a smooth braking zone → LS: front bump / rear rebound.
- Car skips/locks a wheel over bumps under braking → HS front bump too high, or springs/bump stops too stiff.
- Car "floats" and keeps moving after a crest → LS rebound too low.
- Rear steps out over bumps on exit → HS rear (often too much bump, sometimes too little rebound so the wheel doesn't return).
Typical numbers. Segers' Viper example spends ~30–37 % of a lap in low-speed bump and rebound per corner and ~13–21 % in the high-speed ranges; the rear showed far higher HS velocities than the front – the diagnosis was too little rear HS damping.
Pitfalls
- LS adjusters on many dampers also shift the whole curve (bleed adds force at all velocities); HS adjusters often change the knee preload. Read the dyno curves.
- Filtering: velocity from a noisy pot exaggerates HS content. Keep two velocity channels: (a) a body/direction channel low-passed at ~5–8 Hz; (b) a full-band velocity for histograms, low-passed at ~30–50 Hz with pots sampled at ≥ 200–500 Hz so wheel hop (12–20 Hz) is kept. Use the same filter for every run you compare.
Low-speed vs high-speed damping: body vs wheel: L3 Advanced explanation
Why the split works – and where it fails
Frequency separation. Body modes sit at 2–5 Hz with amplitudes of a few mm → velocities of ~10–60 mm/s. Wheel-hop modes at 12–20 Hz with 1–5 mm amplitudes → 75–600 mm/s. The velocity split is therefore a proxy for a frequency split. It works because amplitudes are similar while frequencies differ by ~5×.
It fails when:
- Large, slow body motions (heavy GT car, big kerb-induced roll) reach HS velocities – the HS adjuster then changes body control.
- Small, fast inputs (fine ripple at Vmax) stay in LS velocities – the LS adjuster then affects high-frequency grip.
- Aero cars: body motion from aero load changes is slow but large; and stiff platforms produce tiny body velocities, so the LS range is narrower (< ~15 mm/s) and LS clicks feel very powerful.
Optimum damping depends on the objective. Segers ch12 shows that the damping minimising body motion (platform) is higher than the damping minimising tyre load fluctuation (grip). Digressive curves let you sit near the platform optimum at LS and near the grip optimum at HS.
Body vs wheel ζ (targets): LS body ζ ≈ 0.6–0.8 (sometimes > 1 in rebound on aero cars), HS wheel ζ ≈ 0.3–0.5 – see the damping-ratio lesson. A digressive curve with LS slope ~1.5–3× the HS slope is consistent with those targets on typical GT/formula parameters.
Interaction with springs. Softer springs make the same damper more "LS-effective" (higher ζ, lower velocities) – Segers' histogram simulation shows a softer spring sharpens the histogram like extra damping. Spring and damper changes are never independent.
Key formulas
- f
- frequency (Hz)
- X
- amplitude at the damper (mm)
- filtered damper position (mm)
Trackside takeaways
Low/high speed = shaft velocity, not car speed.
Segers ranges: < 5 friction, 5–25 body (LS), 25–200 road (HS), > 200 kerbs (mm/s); knee is car-specific.
LS controls body motion and transient balance – what the driver feels. HS controls tyre contact over bumps – mostly seen in data.
Use a filtered direction channel on a track map to see which corner is in LS bump/rebound where the complaint occurs.
Read dyno curves: LS and HS adjusters are not perfectly independent.
On your car
Heavier cars with bigger body motions: LS knee often ~40–60 mm/s. HS settings matter for kerb-heavy tracks (Zandvoort, Monza chicanes).
Check yourself
GT3 rear corner, damper MR 0.8 (damper/wheel), LS/HS knee at 40 mm/s shaft velocity. Wheel hop: 1.5 mm amplitude at the wheel at 15 Hz. Body roll: 3 mm amplitude at the wheel at 2.5 Hz. Peak shaft velocities, and which adjusters govern each motion?
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.2 Determining in Which Range to Tune the Shock Absorbers
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.3 Shock Speed Ranges
- Segers – Analysis Techniques for Racecar Data Acquisition — §12.4 Suspension Optimization Using Frequency Analysis
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 22 Dampers