Damper fundamentals: force vs velocity, bump vs rebound
A damper produces force from shaft velocity, not displacement. Its force–velocity curve (shape, bump/rebound asymmetry, knee) is what you tune; it only acts while the suspension is moving.
Damper fundamentals: force vs velocity, bump vs rebound: L1 Foundation explanation
Velocity, not position
A spring makes force from how far it is compressed. A damper makes force from how fast it is moving:
with the damping coefficient (N·s/mm) and the shaft velocity (mm/s), positive in bump (compression), negative in rebound (extension). Consequences you must internalise:
- At the peak of a bump or at maximum roll, velocity is zero → damper force is zero. The damper acts on the way to the peak and on the way back.
- In a long steady corner the body has stopped rolling: dampers do nothing for steady-state balance.
- The damper converts kinetic energy to heat. It controls oscillation of the body (≈2–5 Hz) and of the wheel (≈12–20 Hz).
The force–velocity curve
Race dampers are characterised on a dyno as force vs velocity, separately for bump and rebound:
- Linear – constant slope.
- Digressive – steep at low velocity, flatter above a "knee" (typically 25–75 mm/s). The most common race shape: firm body control, softer response to bumps.
- Progressive – soft at low velocity, steeper at high (used for limiting travel on big hits, less common in circuit racing).
See it on the dyno. Below, a crank and scotch yoke move the damper shaft up and down in a sine wave, and a load cell above the damper measures its force. The chart traces force against shaft velocity (rebound on the left, bump on the right) and the bars compare the current force with the bump and rebound peaks.
Try it:
- Set the crank to about 0.5 Hz (shaft speeds up to about 80 mm/s) and compare Rebound clicks 1 and 10: the low-speed part of the rebound curve changes a lot, while above about 100 mm/s the curves come together. Clickers mostly adjust low-speed damping – body control, not bump absorption.
- Raise the crank to 2 Hz: the shaft reaches about 310 mm/s. The bars show the rebound peak about 1.5× the bump peak – the usual race setup.
- Look at the shape: steep up to the knee (about 45 mm/s), much flatter after it – a digressive damper.
Takeaway: a damper is defined by its force–velocity curve, separately in bump and rebound. Low-speed damping (below the knee) controls the body in roll, pitch and heave; high-speed damping (above it) decides how the car rides kerbs and bumps.
Rebound vs bump. Most race cars run more rebound than bump force (often 1.2–2× at the same speed). The reason is where the input comes from. Bump strokes are mostly driven by the road: every newton of bump damping goes straight into the chassis and into a tyre-load spike, so bump is kept lower for compliance. Rebound strokes are mostly the body and wheel returning after the input; rebound damping controls that return so the body does not keep moving and the wheel does not spring back and unload. A side effect: with rebound > bump, repeated bumps lower the mean ride height (packing – see L3). The folklore explanation "rebound must control the stored spring energy" does not hold: measured from static equilibrium the spring acts symmetrically in bump and rebound.
Typical magnitudes: a few hundred N to ~2 kN at 25–50 mm/s, a few kN at 200–300 mm/s, depending on car mass and motion ratio.
Misconception to drop now: "stiffer dampers make the car stiffer in corners". They make the car transition faster into its steady-state attitude; the steady-state roll and balance are set by springs, bars and geometry.
Damper fundamentals: force vs velocity, bump vs rebound: L2 Practitioner explanation
Hardware and adjusters trackside
Construction. Oil flows through a piston with shim stacks (thin steel discs deflecting to open ports) and through a bleed orifice (needle-adjusted). At low velocity most flow goes through the bleed → force ∝ v² for an orifice, approximately linear with a tuned bleed; above the knee the shims lift and the curve flattens (digressive). A gas reservoir (nitrogen, ~10–20 bar typical) prevents cavitation and adds a small, nearly constant "nose" force (gas pressure × rod area – e.g. 15 bar on a 14 mm rod ≈ 230 N) that acts like a preload.
Adjusters
| Type | Adjusts |
|---|---|
| 1-way | rebound (or combined) |
| 2-way | bump & rebound (usually low-speed bleeds) |
| 3-way | LS bump, LS rebound, HS bump (blow-off preload) |
| 4-way | LS & HS, bump & rebound |
"Clicks" are rarely linear: the first few clicks off the closed end often change more than the rest. Use the dyno curves for each click; never assume "2 clicks = 2× change".
Motion ratio. Force and velocity are both scaled by MR, so the coefficient at the wheel is . A damper with MR 0.7 gives only half its coefficient at the wheel.
Checks before blaming the setup
- Dyno each damper after every event or at defined mileage: hysteresis (force lag at direction change), gas pressure, matched pairs left/right (±5 %).
- Temperature: oil viscosity drops with heat → low-speed (bleed-controlled) force falls as dampers warm (endurance stints, hot tracks). Shim-controlled HS force is less sensitive.
- Friction: seals and rod guides add ~20–80 N of Coulomb friction – it dominates below ~5 mm/s (Segers).
What to change for what
- Body motions (roll, pitch, heave from driver inputs and aero) → low-speed settings.
- Bumps, kerbs, ripple → high-speed settings.
- Balance in entry / exit transients → LS bump/rebound front vs rear (see transient lesson).
Damper fundamentals: force vs velocity, bump vs rebound: L3 Advanced explanation
Why asymmetric, and what the curve shape does
Energy view. Over a full bump-rebound cycle the damper dissipates . If rebound is stiffer than bump, more energy is dissipated during extension. Under a repeated road input, asymmetric damping produces a mean force offset – the suspension "packs down" (rebound > bump at high velocity) or "jacks up" (bump > rebound). Race engineers use this deliberately (Segers notes heavy front rebound on aero cars to hold the nose down, increasing rake), but it changes the static platform under bumpy conditions – check mean ride height on bumpy sections vs smooth.
Digressive rationale. Body motions occur at low shaft speeds and need high damping ( ≈ 0.6–0.8+); wheel motions occur at high speeds and need lower ( ≈ 0.3–0.5) so the tyre can follow the road. A single linear coefficient can't satisfy both → the digressive curve is a frequency-separation device implemented in the velocity domain. The knee velocity is chosen near the upper end of body-motion velocities; a GT car's body velocities are higher than a stiff formula car's, so its knee tends to be higher.
Phase. Spring force is in phase with displacement; damper force leads by 90° (in phase with velocity). In a transient like turn-in, damping force therefore arrives early – during the roll build-up – and is gone by mid-corner. That's the physical basis of "dampers tune transients".
Non-ideal effects
- Hysteresis/compliance: oil compressibility, gas and seal compliance make the damper behave like a damper in series with a spring – at high frequency (wheel hop) the effective damping is lower than the dyno slope suggests.
- Cavitation if gas pressure is too low: rebound force collapses briefly after a direction change from high-speed bump.
- Blow-off: preloaded HS valves give a sharp knee; good for kerbs, but too low a preload makes the car float over undulations.
Damper fundamentals: force vs velocity, bump vs rebound: L4 Expert explanation
Modelling for simulation
A damper model good enough for lap simulation and 7-post correlation usually needs:
- Separate bump/rebound piecewise (or spline) F–v curves per click from the dyno, at operating temperature.
- Series stiffness (oil/gas/mount compliance), giving a Maxwell element: the damper's effective coefficient at frequency is . With = 5 N·s/mm and = 1000 N/mm, at 20 Hz = 0.63 → ≈ 0.72c. This explains why wheel-hop control is weaker on track than the dyno slope implies.
- Friction (Coulomb + Stribeck) near zero velocity – matters for low-amplitude ride and for roll-gradient scatter.
- Gas force vs position (reservoir volume change).
- Temperature dependence of the bleed (viscous) branch.
Limits of the linear-ζ language. Damping ratio assumes linear c; with digressive curves the "effective" ζ depends on amplitude and frequency. Equivalent linearisation (equal energy per cycle at the operating amplitude) gives – the right way to compare a digressive curve to a target ζ.
Inerters and hydraulic interconnection extend what "damper" means (force ∝ acceleration; modal damping). Where banned, teams achieve modal separation with third dampers (heave) vs corner dampers (roll/warp).
Key formulas
- damper force (N)
- c
- damping coefficient (N·s/mm)
- v
- shaft velocity (mm/s), + bump
- coefficient at damper
- MR
- damper travel / wheel travel
- reservoir pressure (Pa)
- shaft cross-section (m²)
- excitation frequency (rad/s)
- X
- displacement amplitude (m)
Trackside takeaways
Damper force depends on velocity: zero at maximum displacement and in steady-state cornering.
Digressive curves (steep LS, flatter HS) separate body control from wheel control.
Rebound usually exceeds bump (~1.2–2×): bump is kept low because road inputs arrive as bump strokes; rebound controls the return (and packs the car down over bumps).
Wheel coefficient = damper coefficient × MR²; use dyno curves per click, not click counts.
Dyno regularly: hysteresis, gas pressure, left/right matching, temperature fade.
On your car
Typically 2- to 4-way adjustable dampers (Öhlins, KW, Bilstein…). Many GT3 balance tweaks between sessions are LS damper clicks plus bump-stop gaps.
Check yourself
Mid-way through a long, constant-radius corner the car has reached its steady roll angle. What are the dampers doing?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 22 Dampers
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.1 Shock Absorber Velocity Analysis
- Segers – Analysis Techniques for Racecar Data Acquisition — §11.4.2 Shock Speed Histogram Shape – What Do We Want? · front rebound used to hold the nose down on aero cars