Understeer gradient and steady-state cornering (bicycle model)
The linear bicycle model defines understeer gradient, neutral steer, characteristic and critical speed. In data it becomes the understeer-angle channel, a powerful balance statistic, provided you remember it is only strictly valid in the linear range.
Understeer gradient and steady-state cornering (bicycle model): L1 Foundation explanation
Collapse the car into a bicycle: one front and one rear tyre on the centreline. At very low speed, with no slip angles, the steer angle needed for a corner of radius is the Ackermann (kinematic) angle .
At speed, both axles run slip angles. If the front needs more slip angle than the rear, you need extra steering beyond Ackermann. That extra is understeer:
is the understeer gradient (deg of road-wheel angle per g):
- : understeer. More steer needed as lateral g rises.
- : neutral steer. Steer stays at the kinematic value.
- : oversteer. Less steer needed; above a critical speed the car is unstable without driver correction.
In the bicycle model comes from axle loads and axle cornering stiffnesses:
A heavier front or a less stiff front axle gives understeer. Race cars in the linear range run small positive gradients, of order a few tenths of a degree to ~1° per g at the road wheels. Road cars run more, typically 1.5–4°/g, for stability.
Using you can compute the kinematic angle from logged speed and lateral G. Steering-wheel angle divided by steering ratio, minus that, is the understeer angle (Segers §7.5). It is a key balance channel.
Understeer gradient and steady-state cornering (bicycle model): L2 Practitioner explanation
The understeer-angle math channel (Segers §7.5):
with in m/s², in m/s and angles in degrees. Steps:
- Measure steering-wheel → road-wheel angle on turn plates (outside wheel) to get a steering-ratio function. It may be non-linear.
- Build the kinematic-angle channel from , logged and speed.
- Take absolute values to remove left/right sign conventions.
Example (GT3, m): 150 km/h (41.7 m/s), 1.6 g (15.7 m/s²): kinematic angle . If the logged road-wheel angle is 2.6°, the understeer angle is 1.2°.
How to use it:
- Track map overlay: colour the understeer angle by position to see where the car pushes (entry/mid/exit).
- Lap statistic: average understeer angle per lap (gated for some threshold). Segers' GT1 example: average falling from ~1.0° to ~0.7° over five laps as the rears went off, and the fastest lap had the highest average understeer angle (Segers Table 7.2).
- Stint run chart: trends towards oversteer as rears degrade on RWD cars.
- Driver comparison: lap time vs average understeer angle shows each driver's preferred balance window (Segers Fig. 7.28).
Complementary channels (know what they really measure):
- Attitude velocity (Segers §7.6). Kinematics give , so this channel equals . It is zero in any steady corner, understeering or oversteering, and spikes when body slip is changing: positive when the rear is stepping out, negative when the car is straightening up. It is a transient oversteer/understeer event detector, not a steady-state balance measure.
- Front minus rear lateral acceleration from two accelerometers on the axle centrelines equals (yaw acceleration). Segers §7.7 reads it as a balance indicator; physically it flags rotation building (entry) or dying (exit) and reads zero mid-corner whatever the balance.
- For steady-state balance use the understeer angle, or measured yaw rate vs a bicycle-model reference .
Pitfall: the gradient is defined in steady state, linear range. At the limit, under braking or with large body slip, the numbers are still useful for comparison but not for absolute claims ("the car has 1.2°/g of understeer gradient at 2 g" is meaningless).
Understeer gradient and steady-state cornering (bicycle model): L3 Advanced explanation
Bicycle-model results (RCVD Ch. 5). With axle cornering stiffnesses (N/rad), CG distances to the front and rear axles, and , :
- Understeer gradient: (rad per m/s²).
- Steady-state yaw-rate gain: .
- Characteristic speed (): . Yaw gain peaks there at , and above it more speed gives less yaw response per degree of steer.
- Critical speed (): . The yaw gain goes to infinity and the car becomes divergently unstable without correction.
- Static margin: , where the neutral steer point is where a side force produces no yaw. Positive SM means understeer. For race cars typically a few percent of wheelbase.
Worked example. kg, 45% front, m, effective axle stiffness kN/rad, kN/rad: rad/(m/s²) °/g. m/s ≈ 200 km/h.
Note that the rear axle needs a much higher cornering stiffness (wider rear tyres, rear compliance and toe-in) to keep small but positive on a car with 55% rear weight.
What changes in the linear range: anything that changes effective axle cornering stiffness: tyre size, pressure, camber, compliance steer, toe, roll steer, LLTD (through load-sensitive ), aero load at speed. Dynamically, front roll-steer (bump-steer in roll) is a powerful and often neglected contributor.
Limit balance is a different question. At the limit, balance is determined by which axle saturates first (peak forces, LLTD via load-sensitive μ, aero balance), not by . RCVD Ch. 7 pair analysis and Ch. 8 moment method treat the non-linear case: a car can be mildly understeering in the linear range and limit-oversteering, or the reverse.
Understeer gradient and steady-state cornering (bicycle model): L4 Expert explanation
Model limits and data subtleties.
- Steering compliance and power-steering assistance mean steering-wheel angle ÷ ratio ≠ road-wheel angle under load. In high- corners a GT steering system can lose several tenths of a degree to compliance. Measure the ratio under load (or with a column torque sensor plus a compliance model) for absolute understeer-angle work.
- Ackermann and large steer. The bicycle model's ignores track-width effects. In hairpins ( m) inner and outer wheels steer differently (Ackermann geometry), and the "outside wheel angle" convention (Segers) matters.
- Body slip angle : in steady state . At low speed (the car's nose points outside the path tangent at the CG); above it turns negative (nose points inside, rear drifts out). Optical slip sensors measure directly and let you compute axle slip angles, a much richer balance picture than one understeer number.
- Transient: yaw response has a natural frequency and damping that depend on (RCVD Ch. 6). Two cars with equal can feel very different on entry if their yaw damping differs (rear cornering stiffness and wheelbase dominate). Understeer gradient alone does not capture "nervousness".
- Statistics, not snapshots. Segers' strength is using the understeer angle as a gated, averaged statistic. Bin by speed (aero vs mechanical), by phase (entry: brake > 0; mid: |a_x| < 0.2 g; exit: throttle > 20%) and by . A clean matrix of mean understeer angle per (phase × speed band), run-charted per stint, is one of the most useful balance tools a race engineer can own.
Key formulas
- road-wheel steer angle
- L
- wheelbase (m)
- R
- path radius (m)
- K
- understeer gradient
- axle masses (kg)
- effective axle cornering stiffness (N/rad)
- road-wheel angle (deg)
- lateral acceleration (m/s²)
- V
- speed (m/s)
Trackside takeaways
δ = L/R + K·a_y. K > 0 understeer, 0 neutral, < 0 oversteer.
Understeer angle = road-wheel angle − 57.3·L·a_y/V². Use it as a gated, lap-averaged statistic.
Characteristic speed √(L/K): above it, yaw response per degree of steer falls.
K is a linear-range quantity; limit balance is decided by which axle saturates first.
Effective axle stiffness includes compliance, toe, roll steer and load transfer, not just tyres.
On your car
Power steering and compliance mean steering-wheel angle needs a calibrated ratio. Average understeer angle per lap trending down over a stint is the classic signature of rear degradation on RWD GT cars.
Check yourself
At 144 km/h (40 m/s) and 1.5 g lateral, a car with wheelbase 2.60 m logs 2.0° road-wheel angle. What is the understeer angle?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 5 Simplified Steady-State Stability and Control · Bicycle model, understeer gradient, characteristic/critical speed
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 6 Simplified Transient Stability and Control
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 7 Steady-State Pair Analysis
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.5 The Understeer Angle
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.6 Vehicle Balance with a Yaw Rate Sensor
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.7 Front and Rear Lateral Acceleration · Front−rear difference is L·(yaw acceleration): a transient indicator