Corner weights, cross weight and setting up on scales
Corner weights describe how the static load is shared between the four tyres. The diagonal (cross weight) is adjusted with spring platforms and determines whether the car behaves the same in left- and right-hand corners.
Corner weights, cross weight and setting up on scales: L1 Foundation explanation
Four numbers that must be right
On setup pads (flat-patch scales) you read four corner weights: LF, RF, LR, RR. From them:
- Front weight % = (LF + RF) / total
- Left weight % = (LF + LR) / total
- Cross weight % = (LF + RR) / total – the diagonal (also called "wedge" or "diagonal")
A four-wheeled car is statically indeterminate: like a four-legged table, you can change how much load each diagonal carries without moving any mass. Raising the LF spring platform (perch) pushes LF down harder – LF and its diagonal partner RR gain load, RF and LR lose the same amount. Front % and left % don't change (they're set by where the mass is); only the cross weight does.
See it on the scales. Below, a car stands on four corner-weight scales. Select a corner and turn its spring perch: the four bars (laid out like the car, static weight dashed) and the cross-weight gauge show where the load goes.
Try it:
- Select LF and raise its perch +2 mm: LF and its diagonal RR each gain about 5 kg, RF and LR each lose the same. Cross weight goes from 50.0 to 50.8 % while front %, left % and the total do not move.
- Now select RR and lower it −2 mm: you undo the change, because it acts on the same diagonal. Press Reset all to 0 mm to start again.
Takeaway: perch adjustments move load between the diagonals, never front-to-rear or left-to-right. On this car about 2.6 kg moves per mm of perch (the tyres act as springs in series with the coil-overs, so it is less than the springs alone would give).
Why it matters: with too much LF+RR the front axle is already loaded more on the left and the rear more on the right. In a right-hand corner (load moves left) the front becomes even more unequal → understeer, while the rear evens out → more grip. In a left-hand corner the opposite. The car behaves differently in each direction.
Target: for a car whose CG is on the centreline, 50.0 % cross weight (both diagonals equal). Typical tolerance on a GT3: ±0.3 % (about ±4 kg on a diagonal).
Rule: always set ride heights and corner weights together – they are coupled through the same perch adjustments.
Corner weights, cross weight and setting up on scales: L2 Practitioner explanation
The scale procedure that works
- Prepare the car: race fuel level (or known, documented), driver in seat or driver-equivalent ballast at the driver's CG position, tyres at a defined reference pressure (always the same, so numbers are comparable between events), steering straight, brakes off, gearbox in neutral.
- Level scales/pads: use a laser or precision level; 1 mm error on one pad shows up as a few kg of cross weight.
- Disconnect ARBs (both drop links on one side) so bars cannot hide or create diagonal load. Afterwards check reconnecting does not change corner weights – if it does, the bar is preloaded; correct link length.
- Settle the car: roll it back and forth (or use turntables / slip plates) and bounce each axle – suspension friction (bearings, damper seals) can hold several kg of hysteresis. Read after settling; repeat until readings are consistent within ~1 kg.
- Set ride heights first (front and rear, left/right equal to target), then adjust diagonal: to raise cross weight, raise one diagonal pair's perches (LF and RR) and lower the other pair (RF and LR) by equal amounts – ride heights stay approximately constant while load moves across the diagonal.
- Record everything: corner weights, ride heights, fuel, ballast, pressures, ambient temperature.
Sensitivity: with equal tracks, ignoring tyres and ARBs, a perch change (wheel-referred) at one corner changes each corner load by roughly e.g. GT3 with = 160, = 140 N/mm: ~37 N/mm (≈ 3.8 kg per mm). Stiffer cars are more sensitive – formula cars may move 10 kg per mm.
Pitfalls: checking corner weights on an uneven garage floor; forgetting the driver's weight offset; not accounting for fuel tank position (many cars have the tank offset or a side-mounted tank, so cross weight drifts with fuel burn); measuring with tyres of different wear/pressure left vs right (different rolling radius = a mm of perch).
Corner weights, cross weight and setting up on scales: L3 Advanced explanation
What target, and why not always 50 %
Cross weight of 50 % is "no wedge" only if each axle's left/right split is the same. Let the total left fraction be for both axles: LF = pF, RF = (1−p)F, LR = pR, RR = (1−p)R. Then
With (driver offset in a GT car, side fuel tank) and , the wedge-neutral cross weight is not 50 %. Example: F = 600, R = 750 kg, p = 0.52 → X = (312 + 360)/1350 = 49.8 %. Setting 50.0 % here would add a small amount of wedge. The meaningful target is equal left fraction on both axles (LF/F = LR/R), which is what "wedge-neutral" means.
Effect on the car (steady state). Wedge is a static diagonal preload. In a corner, LLTD adds to it: with LF+RR wedge, front lateral load transfer in a right-hander adds to an already heavy LF → more front load imbalance → understeer to the right, oversteer to the left. Under braking the diagonal also produces slight yaw moments (uneven front brake forces if tyres are load-limited) – brake pull towards the heavier front wheel under threshold braking.
Wedge as a tool
- Ovals (IndyCar): deliberate wedge (via in-cockpit weight jacker on ovals) to balance the car in one direction of turning.
- Track-direction biased circuits (most turns one way): a small wedge (0.3–0.5 %) can help, but costs the other direction – usually a last-resort trim.
- Asymmetric cars: fuel burn shifting the left/right distribution means cross weight drifts through the stint; choose the target at the fuel level that matters (mid-stint / qualifying).
On-track check: compare roll gradients and steady-state understeer left vs right corners; a consistent asymmetry suggests cross weight, ARB preload, or asymmetric bump stops/packers.
Corner weights, cross weight and setting up on scales: L4 Expert explanation
Mechanics behind the diagonal
- Warp stiffness. The diagonal load change per unit warp displacement is the series combination of the front and rear roll stiffnesses (each including tyres and, if connected, ARBs) plus chassis torsion. Because the ARB is in roll, a connected bar dramatically changes the warp sensitivity: with bars connected the same perch turn moves several times more load. That's why corner weights are set with bars disconnected and why a preloaded bar is effectively a permanent wedge.
- Chassis torsion. On a production-based chassis (GT4, TCR), torsional compliance adds in series; corner weights then also change with how the car is supported (e.g. jacks/axle stands vs scales) – always set up on the pads, not on stands.
- Friction hysteresis. Suspension friction can mask several kg: the corner weight read after jacking up differs from after jacking down. Using the mean of an up and a down approach, or slip plates, gives repeatable numbers.
- Dynamic corner weights. With pushrod load cells or calibrated strain gauges, steady-state corner loads on track reveal true diagonal and LLTD (Segers ch10). Track cambers and asymmetric aero loads (yaw) mean the "static" diagonal is only the starting point.
- Tyre stagger and radius. Different rolling radii left/right change effective corner heights by ≈1 mm of radius per ~6 mm of circumference difference – on high-stiffness cars that's kgs of wedge. Match sets, or measure tyre circumferences when chasing small asymmetries.
Key formulas
- W
- corner weight (kg)
- p
- left weight fraction (same on both axles)
- F, R
- front / rear axle weight (kg)
- perch change referred to the wheel (mm)
- front / rear wheel rates (N/mm)
Trackside takeaways
Cross weight = (LF + RR) / total; only perch (diagonal) changes move it, not front % or left %.
Wedge-neutral means equal left fraction on both axles – 50 % only if the CG is on the centreline.
Too much LF+RR → understeer in right-handers, oversteer in left-handers.
Set ride heights and corner weights together, bars disconnected, car settled, driver/ballast and fuel defined.
Reconnecting an ARB must not change corner weights – otherwise it is preloaded.
On your car
Typical tolerance ±0.3 % cross weight. Driver weight is ballasted to a reference in some series; fuel tank location means cross weight drifts with fuel burn – define the reference fuel level.
Check yourself
Corner weights: LF 320, RF 300, LR 360, RR 370 kg. What is the cross weight (LF+RR)?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 18 Wheel Loads
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 12 Chassis Set-up
- Segers – Analysis Techniques for Racecar Data Acquisition — §10.6 Measuring Wheel Loads with Suspension Load Cells