Combined slip and the friction ellipse
A tyre has one friction budget shared between lateral and longitudinal force. The friction ellipse describes the trade, and its non-linearity explains trail braking, exit traction limits and many balance complaints.
Combined slip and the friction ellipse: L1 Foundation explanation
A tyre cannot give its full lateral grip and its full braking grip at the same time. Plotting the maximum available against gives roughly an ellipse:
For racing slicks and are similar (often within ~10%), so it is close to a circle; hence the common name "friction circle".
The key engineering insight is the non-linearity. Because it is a circle and not a diamond, the first bit of longitudinal force costs very little lateral force, and the last bit costs a lot:
| Lateral force used | Longitudinal force still available |
|---|---|
| 50% | 87% |
| 80% | 60% |
| 90% | 44% |
| 95% | 31% |
So a rear tyre at 90% lateral utilisation mid-corner has under half its traction available. That is why exits are limited by how fast the driver can unwind steering while adding throttle, and why a car that is "loose on throttle" is often simply asking the rear for more than the ellipse allows.
The same logic explains trail braking: the driver blends brake pressure out as steering builds, keeping the tyre on the edge of the ellipse rather than inside it. A driver who brakes in a straight line then turns, with a gap between, leaves the tyre under-used in that gap. In g-g data this shows as a "notch" or diamond shape between the braking and cornering lobes.
Combined slip and the friction ellipse: L2 Practitioner explanation
Seeing combined slip in data.
- g-g plot (lat vs long G). An experienced driver's trace hugs a rounded envelope. A less experienced driver shows a "cross" or diamond shape, with braking and cornering done separately. Segers §7.2 uses exactly this to compare two drivers through a chicane.
- Combined G against distance. Dips between braking and apex show lost time in the transition.
- Brake release vs steering. Plot brake pressure and steering angle together. A good trail brake has brake decaying roughly as steering rises, with release rate matched to the car's rotation needs.
Setup levers that act through the ellipse:
- Brake bias sets which axle reaches the ellipse edge first on entry. Rearward bias with trail braking puts the rear closer to the edge and gives rotation, or instability.
- Differential coast/power locking decides how longitudinal force is shared left/right, which moves the inside and outside tyres to different points on their ellipses.
- Engine braking / coast maps add rear longitudinal force on entry, using rear budget.
- TC limits rear longitudinal demand when lateral demand is high. Modern GT TC uses lateral G or steer as an input for this reason.
Pitfall: the vehicle g-g envelope is not a single tyre ellipse scaled up. Load transfer moves four tyres to different loads, aero changes the size with speed, and the longitudinal-positive side is power-limited. "We are not using the circle" sometimes means the driver is not committed, and sometimes means the car's envelope really is diamond-shaped in that phase because of balance (e.g. entry oversteer stopping the driver trailing the brake).
Combined slip and the friction ellipse: L3 Advanced explanation
Slip-vector view. In a brush model with isotropic friction, combined behaviour is best understood through the combined slip vector , with and . Once sliding dominates, the resultant force points opposite to the sliding-velocity direction. Two consequences:
- Adding longitudinal slip at a fixed slip angle rotates the force vector and reduces even below the peak. In the linear region the reduction is small; near saturation it is large. This is why a small amount of brake on corner entry can rotate the car (rear falls with rear , which is a yaw moment).
- Different longitudinal and lateral stiffness () means equal-force contours are not circles at low utilisation. The ellipse is the envelope of peak forces, not a constant-slip contour.
Pacejka MF combined slip uses weighting functions and multiplying the pure-slip forces, plus a -induced lateral force , a function of whose amplitude depends on load and camber and is reduced as slip angle grows. When you fit tyre data (RCVD Ch. 14), combined-slip coefficients are the least well-measured and the most important for corner entry and exit.
Ellipse anisotropy. by a few percent is common on slicks. Tread pattern (wets) and construction can reverse it. Load sensitivity is not identical in x and y either, so the ellipse shape changes with load. At high downforce the envelope gets bigger but slightly more elliptical.
Vehicle-level synthesis. With four tyres each on its own ellipse, the vehicle's available at each moment is also limited by yaw moment balance. On corner entry you may have spare tyre capacity but no way of using it without exceeding the yaw moment the driver can control. RCVD Ch. 8 (the MRA moment method) and Ch. 9 (the g-g diagram) formalise this. The g-g diagram is the projection of a force–moment problem, which is why stability (entry oversteer) can cap the envelope as surely as grip.
Combined slip and the friction ellipse: L4 Expert explanation
Limits of the ellipse idea.
- Transient path. The ellipse is a quasi-steady boundary. Under fast brake release the longitudinal and lateral relaxation lengths differ, so the actual force path cuts inside the steady ellipse. Fast steering-plus-release inputs lose a few percent of grip that a smooth driver keeps.
- Thermal coupling. Operating on the ellipse edge in combined slip generates more heat per unit force than pure slip at the same force, because slip velocity rises. A driver who trails heavily into every corner can be quicker on lap 1 and slower by lap 10 through front surface overheating. The ellipse shrinks with temperature, so lap-time-optimal and stint-optimal driving differ.
- Asymmetric ellipses per wheel. Inside and outside tyres have different camber, load and temperature, so their ellipses differ in size and shape. Diff locking couples the two. Vehicle-level "available grip" is a constrained optimisation, which is why quasi-steady lap sims (QSS) and transient lap sims differ in corner-entry predictions.
- Driver modelling. A lap sim optimal-control solution uses the full combined-slip model and often finds trail-braking profiles that real drivers cannot hold. Drivers trade 1–2% of envelope for margin. When correlating sim and data, gate the comparison by phase (entry, mid, exit) and compare the shape of the g-g trace, not only the peaks.
Expert trackside heuristic: if the driver's g-g trace shows good braking and good mid-corner peaks but a pronounced notch in between, check the car for entry instability (rear rotation under combined slip: bias, coast diff, engine braking, rear toe) before blaming commitment.
Key formulas
- longitudinal force (N)
- lateral force (N)
- peak friction coefficients
- vertical load (N)
Trackside takeaways
One friction budget per tyre. At 90% lateral use only ~44% of longitudinal grip remains.
Trail braking keeps the tyre on the ellipse edge through the entry; a gap shows as a notch in the g-g plot.
Adding longitudinal slip reduces lateral force even below the peak, which is why brake, coast diff and engine braking rotate the car.
The vehicle g-g envelope is limited by yaw stability as well as tyre grip. A "diamond" g-g trace can be a car problem, not a driver one.
Combined-slip driving generates more heat per unit force, so lap-1 technique can cost you by lap 10.
On your car
ABS lets drivers brake deep into the corner with a lot of trail; TC trims rear demand on exit. Check that the ABS map is not cycling at moderate pressures mid-trail, because that shows as a ragged envelope on the g-g plot.
Check yourself
A rear tyre is using 80% of its lateral capacity mid-corner. Using a circular friction model, roughly what fraction of its longitudinal capacity is still available for traction?
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior · Combined slip, friction ellipse
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 8 Force-Moment Analysis · Yaw-moment limits on the envelope
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 9 "g-g" Diagram
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 14 Tire Data Treatment · Combined-slip data
- Segers – Analysis Techniques for Racecar Data Acquisition — §7.2 The Traction Circle