Learn / Steering & Ackermann / Ackermann geometry: 100 %, parallel and anti-Ackermann
L1 · Foundation

Ackermann geometry: 100 %, parallel and anti-Ackermann

Ackermann sets how much more the inside front wheel steers than the outside. It is exact for slow parking-speed turns, nearly irrelevant in fast corners, and at the limit it is really a tool for distributing slip angle between a loaded and an unloaded tyre.

Ackermann geometry: 100 %, parallel and anti-Ackermann: L1 Foundation explanation

The geometry. In a turn the inside front wheel follows a tighter radius than the outside wheel. For both wheels to roll without sideways scrub at low speed, their axes must meet at a common point on the extension of the rear axle. That needs the inside wheel to steer more:

δo=arctan⁡LR+t/2,δi=arctan⁡LR−t/2\delta_o = \arctan\frac{L}{R + t/2},\qquad \delta_i = \arctan\frac{L}{R - t/2}

with LL wheelbase, tt front track and RR the turn radius at the rear-axle midpoint. This is 100 % Ackermann. Equivalent condition: cot⁡δo−cot⁡δi=t/L\cot\delta_o - \cot\delta_i = t/L.

Other settings

  • Parallel steer (0 %) – both wheels steer the same angle.
  • Anti-Ackermann (< 0 %) – the outside wheel steers more than the inside.
  • Percent Ackermann – the actual inside-minus-outside difference divided by the 100 % difference, at a given steer angle.

How big is it? GT3-sized car, L = 2.75 m, t = 1.65 m:

Corner radiusδo\delta_oδi\delta_i100 % difference
15 m hairpin9.86°10.98°1.1°
50 m3.10°3.20°0.10°
100 m fast corner1.56°1.59°0.03°

The difference scales roughly with L t/R2L\,t/R^2. In a fast corner it is far smaller than the 3–6° of slip angle the tyres run at – Ackermann does almost nothing there. In a hairpin it is comparable to the slip angles, so it matters.

How it is built. The steering arms are angled so their extensions point roughly towards the rear-axle centre (the classic Ackermann trapezoid). Changing the steering-arm pickup or moving the rack fore/aft changes the percentage. Many GT3 and prototype manuals offer two or three steering-arm positions.

See it on the turn plates. Below, the front end of a car stands on two turn plates. The steering wheel moves the rack, the track rods turn the steering arms, and the two wheels end up at different angles. The bars compare the inner, outer and ideal (100 %) outer angles; the chart plots toe-out on lock (inner minus outer angle) against the inner angle.

Try it:

  • Pick 0 mm parallel and steer to full lock: both wheels turn by almost the same angle – the curve stays on the zero (parallel) line.
  • Pick +60 mm ≈100 %: the inner wheel turns more. At 26.7° inside the outer wheel is at 20.7°, about 6° of toe-out on lock, following the 100 % curve.
  • Pick −20 mm anti: the outer wheel now turns more than the inner (toe-out goes negative, −1.3° at full lock).
  • Steer only a little: all the curves start together near zero – Ackermann hardly matters at small steering angles.

Takeaway: the steering-arm geometry, not the rack, sets the Ackermann percentage, and its effect grows with lock. It matters in hairpins, much less in fast corners where the tyres' slip angles dominate.

Race practice: most race cars run well below 100 % – often near parallel, sometimes anti – except for very tight street circuits.

Key formulas

100 % Ackermann wheel angles
δo=arctan⁡LR+t/2,δi=arctan⁡LR−t/2\delta_o = \arctan\frac{L}{R + t/2},\quad \delta_i = \arctan\frac{L}{R - t/2}
L
wheelbase (m)
t
front track (m)
R
turn radius at rear-axle centre (m)
Ackermann condition
cot⁡δo−cot⁡δi=tL\cot\delta_o - \cot\delta_i = \frac{t}{L}
Percent Ackermann
%A=(δi−δo)actual(δi−δo)100%⋅100\%A = \frac{(\delta_i - \delta_o)_{actual}}{(\delta_i - \delta_o)_{100\%}}\cdot 100
Slip-angle split, front axle
αo−αi≈(1−A) L tR2−αr tR\alpha_o - \alpha_i \approx (1 - A)\,\frac{L\,t}{R^2} - \alpha_r\,\frac{t}{R}
A
Ackermann fraction (1 = 100 %)
αrα_r
rear axle slip angle (rad)
Interactive

Ackermann steering

Find the ideal outer-wheel angle for 100 % Ackermann, your actual Ackermann percentage and the turn radius.

Ideal (100 %) Ackermann geometry
cot⁡δo−cot⁡δi=tL\cot\delta_o - \cot\delta_i = \frac{t}{L}% Ackermann=δi−δo,actualδi−δo,ideal×100R=Ltan⁡δi+t2\%\,\text{Ackermann} = \frac{\delta_i - \delta_{o,actual}}{\delta_i - \delta_{o,ideal}}\times 100 \qquad R = \frac{L}{\tan\delta_i} + \frac{t}{2}
t is the kingpin (steering-axis) track, L the wheelbase. 0 % = parallel steer, <0 % = anti-Ackermann (outer wheel steers more).
Inputs
Results
Ideal outer angle
16.58 deg
toe-out on lock 3.42 deg
Your Ackermann
58 %
actual Δδ = 2.00 deg
Turn radius (rear axle centre)
8.24 m
inner rear wheel 7.42 m
Turn radius (mid-wheelbase)
8.35 m

Trackside takeaways

  • Ackermann difference scales with L·t/R²: ~1° in a hairpin, ~0.03° in a fast corner.

  • Loaded tyres peak at higher slip angles, so race cars run less than 100 % – often near parallel.

  • Static toe is not Ackermann; measure toe-out on turns at 10–20° with toe zeroed.

  • Changing steering-arm position also changes steering ratio and bump steer.

  • Tight street circuits are the exception where more Ackermann helps.

On your car

Manuals often offer alternative steering-arm/track-rod positions. Most teams stay near the base setting except at street tracks; inside-front temperatures in slow corners are the best tell-tale.

Check yourself

Question 1 / 4L1 · Foundation

For a car with L = 2.7 m and t = 1.6 m, roughly how big is the 100 % Ackermann difference (inside minus outside wheel angle) in a 100 m radius corner?

Further reading
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 19 Steering Systems · Ackermann geometry, percent Ackermann, race-car practice
  • Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 2 Tire Behavior · load sensitivity of peak slip angle
  • Segers – Analysis Techniques for Racecar Data Acquisition — §7.5 The Understeer Angle · kinematic (Ackermann) steering angle – not to be confused with Ackermann steering