Frequency analysis basics: FFT, PSD and the sampling theorem
Suspension behaviour is easier to judge in the frequency domain: an FFT or PSD of damper, ride-height and acceleration signals reveals body and wheel modes, and transfer functions quantify platform control and tyre-load fluctuation.
Frequency analysis basics: FFT, PSD and the sampling theorem: L1 Foundation explanation
Any signal is a sum of sine waves. A Fourier transform breaks a time signal into the amplitude (and phase) of each frequency it contains. For suspension work this is powerful because the road input is essentially random noise – looking at a single bump in the time domain tells you about that bump, while the spectrum characterises the suspension against any input.
What you typically see in a spectrum of damper or vertical acceleration data:
| Band | What it is | Typical race-car values |
|---|---|---|
| < 1 Hz | slow aero load and fuel/pitch changes, driver inputs | – |
| 1.5–6 Hz | body (sprung mass) heave, pitch, roll modes | GT3 ~2.5–3.5 Hz; LMP2/formula ~3.5–6 Hz |
| 10–25 Hz | wheel hop (unsprung mass on tyre stiffness) | ~12–20 Hz |
| > 25 Hz | kerbs, structural modes, tyre cavity, engine | – |
Sampling theorem. To capture a frequency you must sample at more than twice that frequency (Nyquist). Wheel hop at 18 Hz needs > 36 Hz – in practice 200 Hz or more for a clean spectrum; damper velocity work 500 Hz+. Content above half the sampling rate doesn't disappear – it folds back as a false low frequency (aliasing) at Example: 185 Hz engine or structural vibration reaching a damper pot logged at 200 Hz appears at 15 Hz – right in the wheel-hop band, indistinguishable from real wheel hop. Aliased content can never be removed afterwards by digital filtering; it must be stopped before the ADC by an analogue anti-alias low-pass filter (cut-off typically to ). Know which of your logger inputs have one.
Frequency analysis basics: FFT, PSD and the sampling theorem: L2 Practitioner explanation
Practical FFT/PSD workflow.
- Pick a segment with stationary conditions – e.g., a straight or a family of medium-speed corners. Aero load changes stiffness and ride height with speed, so mixing 80 and 280 km/h data blurs modes. Segment by speed band.
- Remove mean/trend (static ride height, slow aero compression).
- Window each block (Hann is the usual choice) to reduce leakage from the block ends.
- Average many overlapping blocks (Welch's method) – a single FFT of random data has huge variance.
- Plot the power spectral density (PSD, units²/Hz) on log axes.
Frequency resolution is set by the block length:
At 500 Hz with 2048-point blocks, s and Hz – fine enough to separate a 3 Hz body mode from a 4 Hz pitch mode.
Reading it. Peaks at body modes indicate where the platform moves most; a sharp, tall peak suggests low damping, a broad low hump higher damping. Comparing damper settings: a well-damped setup lowers the body-mode peak without raising the 5–10 Hz range too much (where over-stiff damping transmits road input to the body and loads to the tyre).
Natural frequency link. A single-degree-of-freedom estimate is , with the ride rate (wheel rate in series with tyre rate) and the sprung corner mass. Do not expect the PSD peak to sit exactly on : on a well-damped race car (–0.8) the peak location depends on the damping ratio, on which signal you analyse (body acceleration, damper displacement or velocity) and on the slope of the road-input spectrum, so 10–20 % differences are normal – and at the body-mode peak almost disappears. Only larger discrepancies, or a peak that moves with speed, point to aero load, bump rubbers/packers engaged, tyre stiffness or a wrong motion ratio in your calculation. With light damping you can estimate from the half-power bandwidth, .
Four-post rig vs track. Rigs give clean swept-sine inputs and measure contact-patch load directly (not possible on a rolling tyre) – ideal for damper comparisons, but no aero, no rolling tyre and no balance information. On track you get reality but noisy, non-stationary data.
Frequency analysis basics: FFT, PSD and the sampling theorem: L3 Advanced explanation
Transfer functions (FRFs). Instead of single spectra, characterise the suspension by output/input ratios:
where is the cross-spectrum and the input auto-spectrum. Check the coherence ; below ~0.8 the FRF at that frequency is unreliable.
Two FRFs matter (Segers ch. 12):
- Road → body motion – platform stability (aero needs a stable ride height).
- Road → tyre deflection / contact-patch load – grip. Load fluctuation costs grip because tyre force is non-linear (concave) in vertical load: the average force of a fluctuating load is lower than the force at the average load.
The damping that minimises the body-motion peak and the damping that minimises tyre-load fluctuation are different – setup is a compromise chosen per track (bumpy street circuit favours grip; smooth high-downforce track favours platform).
Track "virtual rig". With wheel position, wheel load (pushrod) and body vertical acceleration you can estimate hub acceleration and contact-patch force (plus static), then compute FRFs from on-track data. Conditions: must be measured at that corner (or transformed from the CG: ) in m/s² with gravity removed; is the second derivative of wheel travel (pot travel / MR), bump positive; is the suspension force at the wheel (pushrod force × installation ratio). Limitations: double-differentiating pot data amplifies noise at high frequency, so resolution and sampling rate of the pots set the useful upper frequency.
Pitfalls: non-stationarity (aero), non-linearity (bump stops, digressive dampers – the "natural frequency" shifts with amplitude), and leakage from short blocks. Segment by speed, check coherence, and compare like with like.
Frequency analysis basics: FFT, PSD and the sampling theorem: L4 Expert explanation
Beyond quarter-car thinking. A real car couples heave, pitch, roll and warp; the modal shapes depend on front/rear stiffness and mass distribution, and on aero stiffness (downforce sensitivity to ride height acts like an extra, sometimes negative, spring). On ground-effect cars, aero stiffness (negative near the floor, where downforce rises as ride height falls) lowers the effective heave/pitch frequency; if it exceeded the mechanical stiffness the result would be static divergence onto the skids, not an oscillation. Porpoising additionally needs energy input: floor stall below a critical ride height, with a lag before the flow re-attaches, acts as negative aero damping and drives a limit cycle that a mechanical-only – or even a quasi-static aero-map – model will not predict.
Modal identification. With four corner accelerometers and four pots you can decompose motion into modal coordinates (heave = mean, pitch = front−rear, roll = left−right, warp = diagonal) and compute FRFs per mode. Heave/pitch platform control is usually the aero priority; roll and warp affect mechanical balance and tyre loading.
Optimisation metrics. Common objective functions combine RMS contact-patch load variation (grip), RMS of front/rear ride height (aero), and peak pitch/heave transmissibility, weighted per track from a road-profile PSD measured on that track. Teams then sweep damper curves in a validated 7-post/sim model and verify on track with the PSD of ride height and the FRF of tyre load. Always remember the driver: an analytically optimal low-damping setup may give poor transient response and confidence.
Key formulas
- sampling rate (Hz)
- N
- samples per FFT block
- block duration (s)
- f
- true signal frequency (Hz)
- sampling rate (Hz)
- frequency at which it appears in the logged data (Hz)
- k
- effective stiffness (N/m)
- m
- mass (kg)
- cross-spectral density
- auto-spectral densities
- coherence (0–1)
- suspension force at the wheel (N)
- unsprung mass (kg)
- hub vertical acceleration (m/s²)
Trackside takeaways
Body modes sit around 2–6 Hz, wheel hop around 12–20 Hz; log damper pots fast enough to see both.
Aliasing cannot be filtered out after logging – it needs an analogue anti-alias filter before the ADC.
Use windowing and averaged PSDs (Welch); single FFTs of random data are too noisy.
Segment by speed – aero changes stiffness, so mixed-speed spectra blur modes.
Platform (body FRF) and grip (tyre-load FRF) are optimised by different damping – choose the compromise per track.
Check coherence before trusting a transfer function.
On your car
Body modes typically ~2.5–3.5 Hz; bump-stop engagement at high speed shifts the effective frequency – analyse high-speed segments separately.
Check yourself
A damper pot is logged at 200 Hz on an input with no analogue anti-alias filter. Engine vibration at 185 Hz reaches the pot. Where does it appear in your spectrum?
- Segers – Analysis Techniques for Racecar Data Acquisition — Ch. 12 Suspension Analysis in the Frequency Domain (§12.1–12.4, §12.8)
- Segers – Analysis Techniques for Racecar Data Acquisition — §19.2 Analog-Digital Conversion · Nyquist and aliasing
- Milliken & Milliken – Race Car Vehicle Dynamics — Ch. 16 Ride and Roll Rates; Ch. 22 Dampers