Cars / Tatuus T-318 (Formula Regional)
Formula Regional · FIA Formula Regional 1st Gen: FRECA (FR-19 variant, 2019–2025), Formula Regional Middle East (to 2025), Eurocup-3 (2023–2025) and other regional/national series; check which series still run it

Tatuus T-318 (Formula Regional)

The first-generation FIA Formula Regional car (2018 on). It is a carbon tub with halo, a ~270 hp 1.75 L turbo four (Alfa Romeo/Autotecnica; the FRECA FR-19 variant used an Alpine-badged 1.8 L), a Sadev SL-R82 6-speed sequential with LSD and 13-inch slicks (Pirelli in FRECA, Hankook in Eurocup-3). For 2026 FRECA and FRME switched to the second-gen Tatuus T-326 (Toyota-based 3-cylinder) and Eurocup-3 to a new Dallara chassis, so check whether your series still runs the T-318.

The FIA FR 1st Gen technical regulations are restrictive: max 2-way dampers, no third elements, no bump stops of any kind, ARBs with dedicated positions only, and conventional coil springs. Setup is therefore springs, ARBs, dampers (where allowed), geometry and wings. Compared with F4, there is real downforce, an LSD and ~270 hp, so diff work and aero-platform control appear for the first time. Without heave springs or bump stops, the platform has to come from the corner springs and ride height alone.

Specification

Mass670 kg minimum (FIA FR 1st Gen; series may raise it up to 760 kg; power-to-weight must be ≥ 2.5 kg/bhp). At ~270 hp that rule means at least ~675 kg with driver, so series set their minimum to suit the engine; push-to-pass may temporarily go below the ratio
Power~270 hp (200 kW); optional push-to-pass up to +25 bhp for max 15 s per use
EngineAlfa Romeo / Autotecnica Motori 1,742 cc turbo inline-4 (series-dependent; FR-19 used an Alpine/Renault 1.8 L)
GearboxSadev SL-R82 6-speed sequential
DifferentialLimited-slip differential (Sadev)
Tyres13-inch slicks, supplier series-specific (Pirelli in FRECA, Hankook in Eurocup-3); FRECA sizes 230/570 R13 front, 300/590 R13 rear (public spec sheets)
AeroFront wing with adjustable flap and homologated gurneys; multi-position rear wing
BrakesBrembo 4-piston calipers, ventilated discs
ElectronicsSpec ECU and data logging; no TC/ABS
ChassisCarbon monocoque, halo; double wishbone pushrod with twin dampers front and rear; wheelbase 2,750 mm

Regulations & BoP

  • FIA Formula Regional 1st Gen technical regulations: spec Tatuus chassis; max 2-way single-tube dampers, no third element, no bump stops, ARBs with dedicated positions only, conventional coil springs only.
  • Minimum weight 670 kg (series may raise it up to 760 kg); power-to-weight ≥ 2.5 kg/bhp.
  • Push-to-pass permitted: max +25 bhp, max 15 s per use.
  • Tyres: single supplier per series (Pirelli in FRECA, Hankook in Eurocup-3).
  • For 2026 FRECA and FRME moved to the 2nd-gen Tatuus T-326 (Toyota-based engine) and Eurocup-3 to a new Dallara chassis.

Engineering focus

  • Platform control without third elements or bump stops (springs and ride height only)
  • First real exposure to LSD tuning and aero balance for junior drivers
  • Aero balance with front flap, rear wing and rake
  • Tyre pressures on 13-inch tyres
  • Junior driver development with data (braking, minimum speed, throttle)

What can be adjusted

ParameterRangeFreedomNotes
Springs (front / rear)Tatuus / series-approved rates; conventional coil springs only◐ LimitedWith no third element or bump stop, the corner springs carry all heave stiffness. Stiffer springs hold the floor and front wing at speed but cost mechanical grip over bumps and kerbs. This is the central trade-off of this car.
Front anti-roll barDedicated positions only (sliding adjusters banned)◐ LimitedMid-corner balance. 1 step stiffer front ≈ +1–2 % front LLTD → more understeer, quicker response.
Rear anti-roll barDedicated positions only◐ LimitedRotation vs traction. With an LSD the rear bar can be stiffer than on an open-diff F4 without inside-wheel spin.
Bump stopsProhibited (FIA FR 1st Gen Art. 10.5.5)○ FixedUnlike GT3/F2, there are no bump rubbers to catch the platform. High-speed ride-height control comes only from springs and static ride height.
ParameterRangeFreedomNotes
DampersMax 2-way adjustment allowed by regs; some series run non-adjustable spec units◐ LimitedPublic spec sheets describe Koni twin dampers as non-adjustable in some series, so check your championship. Where clicks are allowed, rebound is the main transient tool (entry stability front, exit squat rear).
ParameterRangeFreedomNotes
Ride heights / rakePushrod adjustment; skid/plank limits● FreeMain aero balance and platform tool. Without heave springs the front drops a lot under aero load: check front ride height at speed on the damper potentiometers before lowering further.
CamberShims within mechanical range● FreeAdjust on tyre temperature spread. The 13-inch tyre has a tall sidewall, so it is sensitive to camber and pressure. Small changes show clearly in temperature.
ParameterRangeFreedomNotes
Toe (front / rear)—● FreeRear toe-in for stability and traction. Front toe-out for turn-in. Change in small steps: at this weight toe effects are large.
ParameterRangeFreedomNotes
Front wing flap / gurneyHomologated flap positions and gurney options◐ LimitedMain front aero trim. One flap step is the standard fix for high-speed understeer when the mechanical balance is right.
Rear wing angleHomologated positions◐ LimitedRear downforce and drag. Choose per track speed, then balance with front flap and rake.
ParameterRangeFreedomNotes
Brake biasCockpit knob● FreeNo ABS. Within a stop, falling downforce is handled by trail release, not bias. Over a race, adjust bias to the lock-up pattern in the data as fuel burns and tyres wear.
ParameterRangeFreedomNotes
Push-to-passUp to +25 bhp, max 15 s per use (FIA FR regs; series sets number of uses)◐ LimitedStrategy tool for attack and defence. Plan uses in the race brief.
EngineSpec, sealed○ FixedNo maps. Engines are allocated by the series.
ParameterRangeFreedomNotes
Gear ratiosSpec ratios○ FixedUsually fixed by the series.
ParameterRangeFreedomNotes
LSD settingsPreload/ramps within approved parts◐ LimitedFirst car on the ladder where diff tuning matters. More preload/lock helps exit traction and entry stability but costs rotation in slow corners.
ParameterRangeFreedomNotes
Tyre pressuresWithin the series tyre supplier's window● FreeKey lever: target hot pressures per axle. Short races make warm-up as important as peak grip.
Tyre allocationLimited sets per event◆ BoP / homol.Usually few new sets per weekend. Plan qualifying sets.

Typical complaints & first tools

Driver / car issueUsual first fix
High-speed understeerFront flap up one step or more rake; check front ride height at speed
Floor bottoming at high speedRaise ride height or stiffer springs (no bump stops available)
Mid-corner understeer in slow cornersSofter front ARB, check front camber and pressures
Exit oversteerSoften rear ARB, adjust LSD, coach throttle application
Front lock-upsBias rearward, check brake temperatures and front pressures