Tatuus F4-T421
The second-generation FIA F4 car (2022 on), used by most F4 championships worldwide. It has a carbon tub with halo, a 1.4 L turbo four (Abarth/Autotecnica FTJ, ~160–180 hp depending on series) and a Sadev SLR75-14 6-speed sequential with an open differential (no LSD). Suspension is pushrod/twin damper/spring at both ends with Andreani 2-way dampers and blade-adjustable ARBs.
For a junior car, the T421 has real engineering content. The Tatuus user manual (v2.1.0) publishes spring options with wheel rates, ARB roll stiffness tables, motion ratios, wing tables and aero sensitivity maps. That makes it the best car in this list for learning to quantify a setup change. The open diff and ~570 kg (with driver) make inside-rear wheelspin and mechanical grip the dominant topics, together with tyre pressures on spec slicks.
Specification
| Mass | ~570 kg minimum including driver (series regulations); ballast locations 15 kg + 5 kg max |
| Power | ~160–180 hp depending on series and engine supplier |
| Engine | Abarth / Autotecnica Motori FTJ 1.4 L turbocharged inline-4 (series-dependent engine supplier) |
| Gearbox | Sadev SLR75-14 6-speed sequential; standard ratios 2.50 / 1.88 / 1.50 / 1.25 / 1.04 / 0.87, final 31/10 |
| Differential | Open differential (no limited slip) per Tatuus manual |
| Tyres | Series-spec slicks (supplier varies by championship) |
| Aero | Front wing with shim-adjustable flap (3/5/7°) and optional 15 mm gurney; rear wing 2–21° in 20 positions (A1–D5); datum balance ~40 % front |
| Brakes | TM calipers; master cylinders 19.05 mm front / 20.68 mm rear; cockpit bias knob |
| Electronics | Spec ECU and dash; optional damper potentiometers and accelerometer; no TC/ABS |
| Chassis | Carbon/Al-Nomex honeycomb monocoque, halo; pushrod twin dampers/springs front and rear; Eibach 36 mm springs |
Regulations & BoP
- FIA F4 Gen2 (Art. 275 F4 regulations): spec Tatuus T421 chassis with halo, series-specific engine supplier, single tyre supplier per championship.
- No TC/ABS and open differential per Tatuus spec.
- No gurney flaps on any rear aerofoil (FIA technical regulation, as noted in the Tatuus manual); front-wing gurney only as homologated part.
- Each championship's technical regulations define the setup freedom (e.g. damper clicks, spring list, ratio stages). The Tatuus user manual lists all parts, ranges and baseline settings.
Engineering focus
- Quantifying setup changes with the manual's wheel-rate, roll-stiffness and aero-sensitivity tables (e.g. computing LLTD per ARB blade)
- Mechanical grip and exit traction with an open differential
- Aero balance with front flap (3/5/7° + gurney) and rear wing (20 positions)
- Tyre pressures and warm-up on spec slicks in short races
- Coaching junior drivers using data: braking, minimum speed, throttle application
What can be adjusted
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Front springs | 700 / 900 / 1000 / 1100 lb/in (≈10.2–16.0 daN/mm at the wheel from k·MR²); MR (damper/wheel) ≈ 0.91, quoted in the Tatuus manual as 1.1 wheel/damper. Wheel rate = k·MR² | ◐ Limited | Front ride frequency and aero platform. Baseline 700 lb/in. Stiffer front holds front-wing height under braking (front wing is ground-effect sensitive) but costs mechanical grip over bumps. |
| Rear springs | 700 / 900 / 1000 / 1100 lb/in (≈8.1–12.7 daN/mm at the wheel from k·MR²); MR (damper/wheel) ≈ 0.81, quoted in the Tatuus manual as 1.23 wheel/damper | ◐ Limited | Baseline 900 lb/in. With an open diff, a softer rear helps keep the inside rear loaded on exit (less wheelspin). |
| Front anti-roll bar | 22 or 25 mm bar × 3 blade lengths → ~1,600–3,600 daN·m/deg roll stiffness at ground | ◐ Limited | Big range: 22 mm soft blade to 25 mm stiff more than doubles front roll stiffness. The manual derives it as bar torsion stiffness × (bar twist per degree of chassis roll)², e.g. 19,642 daN·mm/deg × 9² ≈ 1,590 daN·m/deg (one soft-bar setting). For comparison, the 700 lb/in front springs give only ~200 daN·m/deg (k_w·t²/2 with a ~1.51 m front track), so the bar dominates front roll stiffness. Baseline 22 mm, blades S/S. Use blade steps for fine LLTD changes. Stiffer front = more understeer, sharper response. |
| Rear anti-roll bar | 10 or 14 mm bar × 3 blade lengths → ~50–364 daN·m/deg | ◐ Limited | Rear bar is small relative to the front, so most of the roll stiffness is at the front. Baseline 14 mm H/H. Stiffening the rear rotates the car but loads the inside rear less: watch open-diff wheelspin on exit. |
| Spring preload | Platform thread pitch 1.5 mm/turn | ● Free | Sets ride height/corner weights together with pushrod. Springs must always be preloaded (never loose). |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Dampers (Andreani 2-way) | Bump 12 clicks, rebound 16 clicks (0 = full hard); some series restrict | ◐ Limited | Baseline F: bump 10 / reb 12; R: bump 6 / reb 6 (clicks from closed). Rebound controls load transfer rate on entry/exit. Many national series allow clicks but not valving changes. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Ride height (pushrod) | +1 turn = +5.4 mm front / +6.5 mm rear | ● Free | Baseline 18/38 mm (reference plane). Aero datum is FRH 15/RRH 35 mm. Rake shifts balance forward. Watch skid wear limits. |
| Camber (shims) | +1 mm shim = +0.42° front / +0.30° rear; 0–13 mm front, 0–11 mm rear | ● Free | Baseline −4.0° front, −3.0° rear. Adjust on tyre temperatures and on any supplier camber limits. |
| Caster | +1 turn = +0.47°; nominal 9.4° | ● Free | More caster increases camber gain with steer and steering weight. Rarely changed after baseline. |
| Rear suspension pick-up position | Homologated options (e.g. BE23 / BE24) | ◐ Limited | Changes rear geometry (roll centre/anti-squat). Baseline BE24. Event-level choice. |
| Ballast | Max 15 kg in position 1, 5 kg in position 2 (Tatuus) | ◐ Limited | Light drivers carry ballast to reach the minimum weight. Its position shifts the weight distribution, so put it where it helps the balance and keep it as low as possible. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Toe (front / rear) | +1 turn = 1.12° front total / 1.0° rear total | ● Free | Baseline +20′ front (toe-out in Tatuus convention), 0° rear. Small toe changes have large effect at this weight. |
| UMP (pushrod pick-up on upright) | UMP STD or UMP +15 mm | ◐ Limited | Moves the front pushrod pickup relative to the steer axis, changing wheel drop with steer (jacking) and therefore weight transfer and steering effort with lock. UMP +15 reverses the inner/outer drop pattern. Affects slow-corner balance. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Front wing flap angle | 3° / 5° / 7° shims | ◐ Limited | Main aero balance tool at the front. Datum is 5° with GF15. The manual gives % sensitivity of balance per step. |
| Front wing gurney (GF15) | Homologated 15 mm gurney on/off | ◐ Limited | Adds front load. Rear gurneys are not allowed by FIA F4 regs. |
| Rear wing angle | 2–21°, 20 positions (A1–D5) | ◐ Limited | Baseline A5 (6°). Datum C1 (12°). Each step ~1° changes rear downforce and drag. Choose for track speed. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Brake bias | 1 turn clockwise = +1.5 % front (standard master cylinders) | ● Free | Driver-adjustable via knob. Bias displayed on dash page 2 as front/(front+rear) pressure %. |
| Master cylinders / bias cable | Standard 19.05/20.68 mm; bias cable standard or short | ◐ Limited | The master-cylinder sizes set the bias range and the pedal-force-to-pressure gain. Change only for driver pedal feel (light junior drivers may need more pressure per kg of pedal force), then re-check the bias range. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Engine | Spec, sealed | ○ Fixed | No maps or power adjustment. Engines are usually allocated/rotated by the series to equalise performance. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Gear ratios | Standard stages; optional stages listed by Tatuus, but series normally fix ratios | ○ Fixed | With fixed ratios, gearing issues become shift-point and line choices. Teach drivers to read the rev range through each corner. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Differential | Open differential | ○ Fixed | No LSD: inside-rear wheelspin out of slow corners is managed by rear roll stiffness, damping and driver throttle. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Tyre pressures | Within supplier window | ● Free | Light, low-downforce car on hard-ish junior slicks: pressures strongly affect warm-up and grip. Short races mean tyres must work on lap 1. Set start pressures from the previous session's hot pressures and the track temperature trend. |
| Tyre allocation | Limited sets per event (series rules) | ◆ BoP / homol. | Usually one or two new sets per weekend. Plan which session gets new tyres (qualifying) and run practice on used sets. |
Typical complaints & first tools
| Driver / car issue | Usual first fix |
|---|---|
| Inside-rear wheelspin on slow exits (open diff) | Soften rear ARB (thinner bar/longer blade) or rear springs, coach progressive throttle |
| Mid-corner understeer in slow corners | Softer front ARB blade, check front camber/pressures; UMP option if the car is lazy at big steering angles |
| High-speed understeer | One front flap step up (or add gurney), more rake, or one rear-wing position down |
| Front lock-ups | Bias rearward (1 turn = 1.5 %), check front pressures and brake temperatures |
| Snap oversteer on entry | Bias forward, more rear wing, rear toe-in, soften rear rebound |