Dallara SF23
Super Formula's current car (2023 on). It is a Dallara chassis with 2.0 L turbo four-cylinder engines from Honda (HR-417E) or Toyota (TRD01F) at ~550 hp, plus an Overtake System (OTS) that raises the fuel-flow limit for ~+50 hp. The car is light (~670 kg with driver) and runs on a single Yokohama Advan specification. Its aero was revised versus the SF19 (wings, sidepods, floor) to make following easier. It uses sustainable materials (flax, cork, recycled carbon).
Super Formula is often called the fastest single-seater outside F1. Engineers have more freedom than in F2/F3: front torsion bars, front and rear heave (third) springs, ARBs, alignment, wings, diff. But dampers became spec from 2024 (development banned, inerters banned). With identical tyres and short sessions, success depends on tyre warm-up for one-lap qualifying, platform control and OTS strategy.
Specification
| Mass | ~670 kg including driver (~600 kg dry); confirm in current JRP regulations |
| Power | ~550 hp (~410 kW) + ~50 hp with OTS |
| Engine | 2.0 L turbo inline-4: Honda HR-417E or Toyota TRD01F |
| Gearbox | 6-speed paddle-shift sequential |
| Differential | Limited-slip (spec) |
| Tyres | Yokohama Advan (single supplier and specification) |
| Aero | Revised vs SF19 (wings, sidepods, floor) to improve following; adjustable front flap, rear wing and gurney |
| Brakes | Brembo carbon discs and calipers |
| Electronics | Spec ECU, OTS control, data logging |
| Chassis | Carbon monocoque with sustainable composites, halo; front torsion bars + front heave element, rear coil springs + rear third element (spec Öhlins front and rear third dampers from 2024) |
Regulations & BoP
- Super Formula (JRP): spec Dallara SF23 chassis; Honda or Toyota 2.0 L turbo engines.
- Spec dampers since 2024 (development and inerters banned).
- OTS: fuel-flow increase for ~+50 hp; time-limited per race.
- Tyres: Yokohama Advan single spec.
Engineering focus
- Tyre warm-up for one-lap qualifying
- Platform control with torsion bars, front and rear heave elements and ride height
- OTS strategy
- Aero balance
- Engine-manufacturer differences
What can be adjusted
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Front torsion bars | From Dallara range (bar diameters) | ◐ Limited | Front corner stiffness. Stiffer holds front wing height at speed but costs slow-corner front grip. |
| Front heave spring | Rate and gap/preload from Dallara range | ◐ Limited | Controls front ride height under aero load without adding roll stiffness. Gap sets where it engages. A smaller gap means earlier support at high speed. |
| Rear third/heave spring | Rate and gap from the permitted range | ◐ Limited | Rear platform under aero load without adding roll stiffness. Stiffer or earlier rear support holds rear ride height at speed, which keeps rake and so moves aero balance forward at high speed; too stiff costs rear traction over bumps. |
| Rear springs | From Dallara range | ◐ Limited | Rear platform and traction. Turbo torque out of slow corners in Japan's tight sections (Motegi, Sugo) favours a softer rear, and fast tracks (Suzuka, Fuji) favour a stiffer platform. |
| Anti-roll bars (front / rear) | Bar diameters and arm positions from Dallara range | ◐ Limited | Mid-corner balance tool. Front ARB stiffer = more understeer mid-corner. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Dampers | Spec dampers since 2024; development and inerters banned | ◐ Limited | Since dampers became spec, teams lost a big performance area. The clicks are what is left, so platform control shifts towards torsion bars, heave spring rates/gaps and ride height. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Ride heights (pushrod length) | Turnbuckle pushrod adjustment | ● Free | Main aero balance and platform tool. Longer pushrod raises the corner. Check the at-speed ride height in the data, not just static. |
| Camber | Within mechanical range | ● Free | Tune on tyre temperature spread. Peak grip from the Yokohama has to be reached within one or two laps in qualifying, so warm-up decides the camber choice as much as peak lateral grip. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Toe (front / rear) | — | ● Free | Rear toe-in for stability and traction. Front toe adds heat for one-lap qualifying warm-up but costs drag and long-run temperature. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Front wing flap angle | Within homologated range | ◐ Limited | Front aero balance trim for high-speed corners (Suzuka esses, 130R). |
| Rear wing angle / gurney | Within homologated range; gurney optional | ◐ Limited | Rear downforce and drag. A gurney is a big step in rear load, so balance it with front flap. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Brake bias | Driver-adjustable | ● Free | Carbon brakes: keep them in their temperature window (tape/open ducts) and move bias as fuel burns. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Overtake System (OTS) | ~200 s per race, ~100 s re-arm delay after each use (per sim/team documentation; confirm in sporting regs) | ◐ Limited | Strategy tool for attack and defence. Drivers can see opponents' remaining OTS on lights. |
| Engine | Manufacturer-supplied, sealed | ○ Fixed | Honda/Toyota supply and maintain engines. Teams only select allowed modes. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Gear ratios | Within approved sets | ◐ Limited | Confirm what the current JRP regulations allow. Where a choice exists it is made per track (top speed at Fuji vs acceleration at Motegi). |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Differential | Within spec parts | ◐ Limited | Entry stability vs rotation and exit traction. More lock = stable entry but understeer in Motegi-type hairpins. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Tyre pressures | Within Yokohama recommendations | ● Free | Warm-up for one-lap qualifying is critical: start pressures and out-lap speed decide whether the peak arrives on the push lap. |
| Tyre allocation | Limited sets per event; single spec | ◆ BoP / homol. | Plan qualifying (Q1/Q2) and race sets. A mandatory pit stop/tyre change in many races makes the second set's warm-up a strategy issue. |
Typical complaints & first tools
| Driver / car issue | Usual first fix |
|---|---|
| Tyres not up to temperature for the qualifying lap | Raise start pressures slightly, add toe, revise out-lap procedure and timing |
| High-speed understeer | Front flap up one step. Check front ride height at speed: if above the stall region, soften the front heave or open its gap (front runs lower, more front load). Stiffen the front heave / reduce the gap only if the floor stalls or the skid touches |
| Mid-corner understeer in slow corners | Softer front ARB or thinner front torsion bar, check front pressures |
| Exit oversteer | Adjust diff, softer rear ARB/springs, more rear wing |
| Front lock-ups | Bias rearward, check brake temperatures |