Dallara F3 2025
The third-generation FIA F3 car (2025 on): a Dallara chassis with a new aero package optimised for following, 16-inch Pirelli tyres, the carry-over Mecachrome 3.4 L naturally aspirated V6 (380 hp @ 8,000 rpm), a 3Mo 6-speed gearbox and F1-style hydraulic DRS. Teams receive everything from the series promoter. The FIA technical regulations list exactly what may be changed: wing configurations from the user manual, springs/torsion bars from the supplied list, damper clicks free and valves only from the manual range, diff ramps from approved parts plus preload shims, camber within Pirelli limits.
Gear ratios are defined by the FIA for each competition, so teams do not choose them. The minimum mass is 729 kg without fuel (including driver; 2026 regs, 722 kg in 2025). With 30 identical cars, small setup changes and data comparison with teammates decide grid positions measured in hundredths.
Specification
| Mass | 729 kg minimum without fuel, including driver (2026 FIA F3 technical regulations; 722 kg in 2025) |
| Power | 380 hp @ 8,000 rpm; 420 Nm |
| Engine | Mecachrome V634 3.4 L 95° V6 naturally aspirated |
| Gearbox | 3Mo 6-speed longitudinal, electro-hydraulic paddle shift; ratios defined per competition |
| Differential | Limited-slip; ramp angles and preload adjustable within approved parts |
| Tyres | Pirelli P Zero 16-inch slicks (three compounds in the range) and Cinturato wets |
| Aero | New 2025 aero package optimised for following; hydraulic DRS; HDF rear wing only raced at Monaco |
| Brakes | Spec brake system from the promoter |
| Electronics | Spec ECU and data acquisition; FIA ADR |
| Chassis | Carbon/kevlar monocoque, halo; double wishbone pushrod with twin dampers |
Regulations & BoP
- FIA F3: spec Dallara F3 2025 supplied by the promoter; Type 1/2/3 part classification controls modifications.
- Minimum mass 729 kg without fuel (2026 regs; 722 kg in 2025).
- Gear ratios defined by the FIA for each competition.
- Springs/torsion bars, damper valves, diff ramps: only from approved/promoter range; damper clicks free.
- Wings: user-manual configurations only; HDF only raced at Monaco.
- Tyres: Pirelli 16-inch; minimum pressures and maximum camber policed.
Engineering focus
- Fine-tuning a spec car where small changes decide qualifying in a 30-car field
- Tyre preparation and management (minimum pressures, max camber, few sets)
- Data comparison vs teammates (braking, minimum speed, throttle)
- Diff ramps and ARBs for entry/exit balance
- Race strategy with DRS and sprint/feature formats
What can be adjusted
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Springs / torsion bars | Only those specified by Dallara and supplied by the F3 promoter | ◐ Limited | Platform vs mechanical grip. A stiffer front holds front-wing height under braking (front wing is ground-effect sensitive). Softer helps over kerbs and at bumpy street-type tracks. |
| Anti-roll bars (front / rear) | Within the Dallara range | ◐ Limited | Main mid-corner balance tool. 1 step stiffer front ≈ +1–2 % front LLTD → more mid-corner understeer. |
| Packers / bump rubbers | Only solid packers, metal wool washers and bump rubbers on damper shafts | ◐ Limited | High-speed platform tool: sets where travel stops under aero load. Use to stop the car touching down at the end of long straights. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Damper clicks | Free within the adjustment range of the supplied damper | ● Free | Transient and kerb tool. LS rebound for entry stability, LS bump for turn-in/platform. Confirm with damper-velocity histograms. |
| Damper valves | Only valves listed in the Dallara user manual | ◐ Limited | Event-level choice (street vs permanent circuit). |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Ride heights / rake | Pushrod adjustment; plank wear rules | ● Free | Main aero balance tool. More rake = more front bias and more total load, up to the point where the floor loses performance. Check plank wear. |
| Camber | Within supplier range and Pirelli maximum camber | ◐ Limited | Pirelli's maximum camber is policed at all times. Most teams run near the limit for qualifying and back off for tyre life only if needed. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Toe (front / rear) | — | ● Free | Rear toe-in for stability and traction. Front toe for turn-in. Toe also adds tyre temperature: useful for warm-up, harmful for long-run overheating. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Front wing configuration | Configurations from the Dallara user manual | ◐ Limited | Main front aero trim for high-speed balance. |
| Rear wing configuration | User-manual configurations; HDF only raced at Monaco | ◐ Limited | Track downforce/drag choice. It also changes how much DRS gains. |
| DRS | Hydraulic DRS, enabled by race control | ○ Fixed | Not a setup item, but the rear wing choice changes DRS effectiveness. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Brake bias | Driver-adjustable | ● Free | No ABS. Drivers adjust bias through a stint as fuel and tyre grip change. Rear lock-ups on low-fuel qualifying laps are common. |
| Brake duct taping | Tape allowed for temperature optimisation only | ◐ Limited | Keep brakes in their temperature window at cold events. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Engine | Spec, sealed | ○ Fixed | No maps or power adjustment. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Gear ratios | Defined by the FIA for each competition | ○ Fixed | Same ratios for all cars at each event. Gearing becomes a line and shift-point question. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Diff ramp angles / preload | Ramp parts from the promoter; preload spacers/shims | ◐ Limited | Main entry/exit tool beyond ARBs. More coast lock = stable entry but understeer. More drive lock = traction but power understeer. |
| Parameter | Range | Freedom | Notes |
|---|---|---|---|
| Tyre pressures | Above Pirelli minimum at all times | ◐ Limited | Minimum pressures are policed, so start pressures have to keep the tyres above the minimum. Pressure is not a free balance tool. |
| Tyre allocation | Limited Pirelli sets per event | ◆ BoP / homol. | Very few new sets: one-lap qualifying preparation (out-lap, push-lap timing) is a big part of the engineer's job. |
Typical complaints & first tools
| Driver / car issue | Usual first fix |
|---|---|
| Mid-corner understeer in slow corners | Softer front ARB, reduce diff coast lock, check front pressures |
| High-speed understeer | Front wing configuration step up or more rake |
| Rear tyre overheating in the race | Less rear toe-in, softer rear ARB, coach throttle application |
| Front lock-ups | Bias rearward, check brake temperatures (tape ducts if cold) |
| Exit oversteer | Adjust diff drive ramp, softer rear ARB, more rear wing |