Cars / Dallara F2 2024
FIA F2 · FIA Formula 2 Championship (F1 support)

Dallara F2 2024

The third-generation FIA F2 car (2024–2026+). It is a Dallara chassis with ground-effect-influenced floor, F1-style wings, DRS and 18-inch Pirelli tyres, powered by the Mecachrome V634T 3.4 L single-turbo V6 (~620 hp) through a Hewland 6-speed. Front suspension uses torsion bars and the rear coil springs, both with twin dampers. Carbon brakes (Carbone Industrie discs/pads, Brembo calipers).

Like F3, everything comes from the promoter, and the FIA technical regulations define exactly what can change. Gear ratios are specified by the FIA for each competition. Springs and torsion bars come only from the supplied list, damper valves only from the user-manual range, diff ramp parts from the promoter (plus preload shims), and wing configurations only from the user manual. The HDF rear wing can only be raced at Monaco. Pirelli minimum pressures and maximum camber are policed. Minimum mass is 793 kg without fuel (2026 regs; 785 kg in 2024). Most of the performance difference comes from tyre management (especially in the sprint/feature race format with mandatory pit stop), platform and diff, and the driver.

Specification

Mass793 kg minimum without fuel, including driver (2026 FIA F2 technical regulations; 785 kg in 2024)
Power~620 hp @ 8,750 rpm; ~583 Nm
EngineMecachrome V634T 3.4 L V6 single turbo
GearboxHewland 6-speed sequential, paddle shift; ratios defined by FIA per competition
DifferentialLimited-slip; ramp angles from promoter parts, preload via spacers/shims
TyresPirelli P Zero 18-inch slicks (two compounds per event), Cinturato wets; OZ wheels
AeroGround-effect-influenced floor, F1-style front wing, rear wing with DRS; HDF rear wing only raced at Monaco
BrakesCarbone Industrie carbon discs and pads, Brembo 6-piston calipers; spec parts only
ElectronicsSpec ECU and data acquisition; common ECU configuration files; FIA ADR
ChassisCarbon/aluminium honeycomb monocoque, halo; front torsion bars, rear springs, twin dampers; wheelbase 3,135 mm

Regulations & BoP

  • FIA F2: spec Dallara F2 2024; all parts from the F2 promoter. Type 1/2/3 parts classification defines what can be modified.
  • Minimum mass 793 kg without fuel (2026 regs; 785 kg in 2024).
  • Gear ratios defined for each competition by the FIA.
  • Springs/torsion bars, damper valves, diff ramps: only from approved/promoter range.
  • Wings: user-manual configurations only; HDF rear wing only raced at Monaco.
  • Tyres: Pirelli; minimum pressures and maximum camber from Pirelli's technical preview are policed. No tyre heating devices.
  • Brakes: only promoter-supplied discs and pads.

Engineering focus

  • Tyre management over the feature race (two compounds, mandatory stop) and sprint race on used tyres
  • Platform control: torsion bars, packers, ride height and rake for a floor-sensitive car
  • Diff ramp/preload for entry stability vs rotation
  • Carbon brake temperature management with duct taping
  • Data comparison vs teammates in an identical car

What can be adjusted

ParameterRangeFreedomNotes
Front torsion barsOnly bars specified by Dallara and supplied by the F2 promoter◐ LimitedFront ride and roll stiffness. Stiffer front holds the floor and front wing at a stable height (ground-effect floor is sensitive to front ride height) but reduces mechanical grip over bumps and kerbs.
Rear springsOnly springs supplied by the F2 promoter◐ LimitedRear platform and traction. With ~620 hp turbo torque, a softer rear helps traction out of slow corners at the cost of rear ride-height control at speed.
Anti-roll bars (front / rear)Within Dallara range◐ LimitedMid-corner balance tool. 1 step stiffer front bar ≈ +1–2 % front LLTD: more mid-corner understeer, quicker response.
Packers / bump rubbersOnly solid packers, metal wool washers and bump rubbers on damper shafts◐ LimitedMain high-speed platform tool. Packers decide where the floor stops dropping under load. Too much front packer causes snappy high-speed understeer/oversteer transitions as the car goes onto the stops.
ParameterRangeFreedomNotes
Damper clicksFree within the adjustment range of the supplied damper● FreeThe fine-tuning tool. LS rebound for entry stability, LS bump for platform and turn-in, HS for kerbs. Change 2 clicks at a time and confirm on damper-velocity histograms.
Damper valvesOnly valves listed in the Dallara user manual◐ LimitedEvent-level choice (e.g. street circuit vs smooth permanent track). Valve changes need dyno checks.
ParameterRangeFreedomNotes
Ride heights / rakePushrod adjustment; plank 5 mm nominal, wear limits apply● FreeMain aero balance tool on a floor-influenced car. Lower and more rake = more downforce but more pitch sensitivity and plank wear. Check plank wear after every run.
CamberSpacers in hub/upper wishbone mount, supplier range, within Pirelli max camber◐ LimitedPirelli max camber is policed. Running at the limit is common, so the real camber choice is often how far below the limit you go for tyre life in the feature race.
BallastOnly in locations specified by Dallara◐ LimitedWeight distribution trimming within allowed positions.
ParameterRangeFreedomNotes
Toe (front / rear)—● FreeRear toe-in for stability and traction. Front toe-out for turn-in. Toe also heats tyres: reduce for long feature-race stints if overheating.
ParameterRangeFreedomNotes
Front wing configurationOnly configurations described in the Dallara user manual◐ LimitedFront flap angle is the main balance trim between sessions. Pair with rear wing to keep the aero balance target.
Rear wing configurationUser-manual configurations; HDF only raced at Monaco◐ LimitedTrack-specific downforce/drag level. Low-drag at Monza/Baku. DRS effectiveness depends on the wing chosen.
DRSRace-control enabled○ FixedNot a setup item, but the wing choice changes DRS speed gain.
ParameterRangeFreedomNotes
Brake biasDriver-adjustable● FreeCarbon brakes need temperature. Bias rearward for rotation but watch rear lock-ups on low-fuel qualifying laps.
Brake duct tapingDucts may be partially or fully taped for temperature only◐ LimitedCarbon discs below their window give poor bite. Tape at cold tracks, open fully at Bahrain/Monza.
ParameterRangeFreedomNotes
Side-pod / radiator tapingTape on stone guard or plate on radiator face for temperature only◐ LimitedCooling vs drag. Small but real gain at cold events.
EngineSpec, sealed; common ECU configuration○ FixedNo maps or power adjustment.
ParameterRangeFreedomNotes
Gear ratiosDefined by the FIA for each competition○ FixedSame ratios for all cars at each event. Gearing problems become shift-point and line problems.
ParameterRangeFreedomNotes
Diff ramp angles / preloadRamp parts from promoter; preload spacers ground / circular steel shims◐ LimitedMain entry/exit tool beyond ARBs. More coast ramp lock = entry stability but understeer. More drive lock = traction but power understeer. Preload affects low-speed behaviour.
ParameterRangeFreedomNotes
Tyre pressuresAbove Pirelli minimum at all times (TPMS monitored)◐ LimitedMinimum pressures are policed. Start pressures are set so the tyres never drop below the minimum. Pressure is not a free balance tool.
Tyre allocation / compoundsTwo Pirelli compounds per event; limited sets◆ BoP / homol.Mandatory use of both compounds in the feature race. Plan which sets to save for the race.

Typical complaints & first tools

Driver / car issueUsual first fix
Mid-corner understeer in slow cornersSoften front ARB, reduce diff coast lock, check front pressures not too high
High-speed instability / car "touches down"Raise ride height or add packer, check plank wear and damper potentiometer data
Rear tyre overheating in feature raceReduce rear toe-in, soften rear ARB, coach smoother throttle; adjust diff drive ramp
Front lock-ups on low-fuel qualifying lapsBias rearward slightly, check brake temperatures (tape ducts if cold)
Power oversteer out of slow cornersSofter rear spring/ARB, adjust diff drive ramp, more rear wing