# Operating windows: temperature, hot vs cold pressure, TPMS

> A race tyre only delivers its grip inside a temperature and pressure window. You set cold pressures, but the tyre works at hot pressures, so the engineer’s job is predicting the build-up and verifying it with TPMS.

Area: Tyres · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/tyres-temperature-pressure-windows

## L1 · Foundation

A slick compound's friction depends strongly on temperature. Too cold and the rubber is stiff and glassy (poor grip, risk of graining); too hot and it becomes soft and greasy (grip falls, wear and blistering rise). Each compound has a **working window**. As rough orders of magnitude for surface temperature: harder compounds roughly 90–120 °C, softer ones 70–100 °C. Read the supplier data for your tyre. Segers §8.5 shows how to find the window from your own data: plot lateral G against tyre temperature and look at where the upper envelope peaks.

**Pressure** controls patch size and carcass stiffness. You set **cold** pressure in the garage, but the tyre works at **hot** pressure. Gas in a closed volume obeys roughly $p/T$ = constant (absolute units):

$$p_{hot,abs} = p_{cold,abs}\,\frac{T_{hot}}{T_{cold}}$$

**Example:** cold 1.40 bar gauge at 20 °C (2.41 bar absolute, 293 K). Air temperature in the tyre at running is 80 °C (353 K): $2.41 \times 353/293 = 2.91$ bar abs = **1.90 bar gauge**. That is +0.5 bar, roughly **0.1 bar per 12 °C** of gas temperature at these pressures.

Typical **hot** targets (orders of magnitude; the supplier sets the real numbers): GT3 slicks ~1.8–2.0 bar; Cup cars similar; LMP/Hypercar ~1.7–1.9 bar; formula cars (F4–F2) ~1.3–1.7 bar.

Remember **gauge vs absolute**: gauges and TPMS read gauge pressure (relative to atmosphere), but the gas law needs absolute pressure, so add ~1.013 bar. Forgetting it is the classic error: scaling the gauge value by $T_{hot}/T_{cold}$ predicts only about 55–60% of the real build-up (here +0.29 instead of +0.49 bar), so the cold set comes out too high and the tyre runs over-pressure.

## L2 · Practitioner

**The engineer's pressure loop.**
1. **Target**: hot pressure from the supplier window and your own data (balance, temps, wear).
2. **Predict build-up**: from previous runs at similar ambient/track temperature, fuel load and driver. Typical build-ups: GT3 from cold (no blankets) +0.4–0.7 bar; from blankets much less, because the blanket already raised the gas temperature.
3. **Set cold** (or blanket-hot) pressure = target − predicted build-up.
4. **Verify with TPMS** and correct for the next set.

**TPMS realities (Segers §8.2):**
- Pressures and gas temperatures take **several laps to stabilise**, often 4–7 laps on a GT car, even after pre-heating. Judging balance or setup changes in the first 2–3 laps of a run is risky: the front/rear pressure ratio is not yet at its stable value.
- RF dropouts show as spikes to zero. Build alarms that also check the TPMS temperature signal, so a dropout isn't mistaken for a puncture.
- Use the ideal-gas correction to compute an **equivalent cold pressure at a reference temperature** (e.g. 20 °C) from TPMS hot readings. Comparing sets on that basis removes ambient variation.

**Rules.** Many series now enforce **minimum pressures** with TPMS (minimum hot or minimum running pressure, with penalties); supplier minimum starting pressures are common in formula series. Running under the limit is a regulation risk as well as a tyre-safety one.

**Tyre warmers.** Where allowed (F1, and some national GT and sports-car series), blankets bring the carcass and gas up to blanket temperature (regulated, typically 70–100 °C), so set pressures are "hot set" and build-up is small. Where banned (WEC since 2023, with a one-off exemption for Le Mans 2023; many GT championships; F2, F3, F4/FR; IndyCar; Super Formula), the out-lap is a big variable. Track temperature, driver warm-up technique and the first few corners decide when you hit the window.

**Pitfalls:** nitrogen vs air matters mainly through **moisture**. Wet air builds more pressure as water vaporises, so use dry gas. Rim and brake heat soak raise gas temperature in heavy-braking stints (fronts in particular), so pressures can keep climbing through a stint. Plan for the stint's end condition as well as its middle.

## L3 · Advanced

**Thermal structure.** A tyre has (at least) three relevant temperatures:
- **Surface** (what IR sensors see): responds within fractions of a second to sliding power ($F\cdot$slip$\cdot V$), cooled by air and track.
- **Bulk/tread core** (what a needle probe reads in the pits): slower, tens of seconds to minutes. It governs compound stiffness and hysteresis, and therefore grip.
- **Carcass/gas**: slowest. Gas temperature sets pressure, and it is fed by the carcass and by rim heat from brakes.

Segers' Eq. 8.3 (after Nowlan) is a single-node version: heating from $\sqrt{(F_y\alpha V)^2 + (F_x\kappa V)^2}$, cooling to air and track. It explains why temperature builds in long loaded corners and falls on straights, and why a driver's style (V-shape vs long trail braking) shifts temperatures.

**Finding the window from data.** Plot $|a_y|$ (or an axle-force estimate) against axle-average surface temperature for many corners. The **upper envelope** peaks inside the window (Segers' example: ~1.8 g achieved with fronts 53–73 °C and rears 61–93 °C). Then build **time-in-window** channels: per-lap percentage of time each tyre is below, inside, or above the window. These are excellent run-chart statistics for comparing setups and drivers.

**Pressure as a tuning parameter.** Within the allowed range, pressure trades:
- higher: smaller patch, higher carcass stiffness (sharper response), lower hysteresis heat in the carcass, higher surface sliding, usually higher load sensitivity;
- lower: bigger patch, more carcass flex (more heat in the sidewall and shoulders), softer vertical rate (helps mechanical grip on bumps, changes ride heights by ~1 mm per 0.1 bar on many cars).

Tyre **vertical stiffness** scales with pressure. On aero cars a 0.1 bar change moves ride height and aero balance, so pressure changes are not purely tyre changes.

## L4 · Expert

**Stint planning and the moving target.** Because gas temperature lags surface temperature, the pressure you see at lap 3 is not the pressure at lap 20. For endurance stints, model pressure vs lap with a first-order lag plus a brake-heat term and fit the coefficients from TPMS data across stints. Use that to choose a start pressure that **centres the stint** in the window rather than hitting target at lap 5 and overshooting by lap 25.

**Ambient corrections.** Track temperature affects the surface and bulk window. Ambient affects starting gas temperature. A 10 °C change in starting gas temperature changes predicted hot pressure by ~0.08–0.1 bar at the same build. Many teams use a correction table (cold set vs garage temperature) and log the actual tyre-gas temperature at fitting.

**Minimum-pressure regimes** distort the optimum, and which rule applies changes the levers. Under a **minimum cold/starting pressure**, the grip-optimal running pressure is often below what the legal start produces, so teams want *less* build-up: they limit gas heating (rim and brake-duct cooling) and raise *tread* temperature through slip, camber and warm-up technique instead. Feeding brake heat into the rim would raise pressure further, the opposite of the aim. Under a **minimum hot/running pressure** (TPMS-enforced), running pressure is pinned near the limit anyway, so rim heat mainly changes which cold set you need and how far pressure falls on cool laps. Brake-duct blanking is then a pressure-security lever (for example behind a safety car), not a grip lever.

**Uncertainty you should communicate:** TPMS sensors have ~±0.02–0.03 bar accuracy and their gas temperature is measured at the rim, not in the bulk gas. Hot pressure targets from suppliers carry tolerance bands. Don't chase 0.01 bar trends across sets without enough laps to be statistically meaningful.

## Key formulas

**Ideal-gas pressure build-up (absolute units)**

$$p_{hot,abs} = p_{cold,abs}\,\dfrac{T_{hot}}{T_{cold}}, \quad p_{abs} = p_{gauge} + 1.013\,\text{bar}$$

- T: gas temperature in kelvin

**Equivalent cold pressure from TPMS**

$$p_{cold,gauge} = (p_{TPMS} + 1.013)\,\dfrac{T_{ref} + 273.15}{T_{TPMS} + 273.15} - 1.013$$

- p_TPMS: measured gauge pressure (bar)
- T_TPMS: TPMS gas temperature (°C)
- T_ref: reference temperature (°C)

**Rule of thumb build-up**

$$\dfrac{dp}{dT} = \dfrac{p_{abs}}{T} \approx 0.008\,\text{bar/K} \;(\approx 0.1\,\text{bar per } 12\,\text{K})$$


## Trackside takeaways

- You set cold pressure; the tyre works at hot pressure. Always do gas-law maths in absolute units.
- ~0.1 bar per 12 °C of gas temperature at typical race pressures.
- Pressures take several laps (often 4–7) to stabilise. Don’t judge balance on lap 2.
- Find your real temperature window from data: lateral G vs tyre temp, upper envelope.
- Pressure changes tyre vertical stiffness too, so on aero cars it moves ride height and aero balance.
- Respect supplier and regulation minimum pressures. TPMS-enforced penalties are common.

## By car category

### GT3

No tyre warmers in most major GT3 championships, so the out-lap and the first 2–4 laps are cold-tyre laps. Minimum running pressures are monitored by TPMS in many series. Build-up from cold is typically ~0.4–0.7 bar depending on track and ambient.

### FIA F2

No tyre blankets: Pirelli designs the F2 compounds to switch on at a much lower temperature than the F1 tyres. Cold set is well below the running target, so the build-up is large, supplier minimum starting pressures apply, and out-lap and first-sector warm-up decide qualifying.

### FIA F3

No blankets. Out-lap warm-up, track temperature and the first sector decide when tyres reach their window, and qualifying out-lap preparation (weaving, braking, slip) is a key performance item.

### Hypercar (LMH/LMDh)

Warmers banned in WEC since 2023 (with a one-off exemption for Le Mans 2023), and at every round including Le Mans since 2024. Michelin compounds must reach temperature on the out-lap, and multi-stint (double/triple) planning of pressures and compounds is central to race strategy.

### Super Formula

No tyre warmers and a light, high-downforce car: cold-tyre out-laps are notoriously tricky, and the Yokohama tyres’ warm-up behaviour drives qualifying run plans.

### IndyCar

No tyre warmers. Pressures and stagger on ovals are tuned together; on road courses, alternate (softer) tyres have a narrower temperature window and degrade faster.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.2 Working with Tire Pressure Monitoring Systems (Stabilisation, RF dropouts, ideal gas law)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.4 Where Does Tire Temperature Come From?
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.5 Working Temperature Range of the Tires
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior (Temperature and pressure effects)
