# Tyre degradation: graining, blistering, thermal vs wear deg, management

> Lap time lost over a stint comes from distinct mechanisms (graining, blistering, thermal degradation, wear) with different signatures and different cures. Diagnose the mechanism before changing the car or the driver’s approach.

Area: Tyres · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/tyres-degradation-management

## L1 · Foundation

**Degradation** is the loss of tyre performance over a stint, usually measured as **lap time lost per lap after correcting for fuel burn**. The main mechanisms:

| Mechanism | What happens | Visible sign | Typical cause |
|---|---|---|---|
| **Graining** | Surface rubber tears into rolls ("grains") that stick to the tread; the tyre rides on them | Ridged, rough surface across the tread | Tread too **cold** for the sliding it is asked to do; green/dusty track; soft compound |
| **Blistering** | Rubber overheats internally; gas pockets form and burst, leaving craters | Holes/craters, often on one shoulder or centre | **Bulk** too hot: high camber, high pressure, overload, hot track |
| **Thermal degradation** | Surface/bulk above window; rubber gets greasy, grip falls; partly recoverable if cooled | High IR temps, falling grip, balance drift | Overdriving, sliding, wrong balance |
| **Wear** | Tread rubber removed; compound ageing over heat cycles | Tread depth reduced, wear indicators | Distance, abrasion, sliding energy |

**Fuel correction.** A car gets faster as fuel burns. A rough figure is **~0.02–0.04 s per kg per lap** depending on track length and car, so over a 60 kg stint the car gains roughly 1.2–2.4 s from fuel alone. Raw lap times can hide real degradation.

**Graining is often temporary.** Once the grains wear off (a few laps if the driver manages the sliding), the tyre "cleans up" and pace returns. **Blistering is not**: the damage is structural and progressive.

## L2 · Practitioner

**Diagnosis in data.**
- **Fuel-corrected lap time trend.** Linear slope = steady deg (wear/thermal). A dip that recovers = graining that cleaned up. An accelerating loss ("cliff") = wear-through or thermal runaway.
- **Grip-factor run charts** (Segers §8.1): average combined G gated for grip-limited situations (overall >1 G, cornering lateral >0.5 G, braking long <−1 G, traction long >0 with lateral >0.5 G, aero lateral >1 G above 120 km/h). Which factor drops tells you which axle and phase is degrading: traction grip falling means rears; cornering and aero grip falling with stable traction means fronts.
- **Balance drift.** Average understeer angle per lap (Segers §7.5) trends towards oversteer when rears degrade faster (typical RWD GT on traction-limited tracks) and towards understeer when fronts degrade (front-limited, long-corner tracks).
- **Temperatures and pressures**: rising surface temperature and time-above-window plus falling grip factor point to thermal deg.

**Setup and driving levers:**
- **Rear thermal deg on exit**: softer rear roll stiffness, more diff power-ramp locking only if it reduces wheelspin, a gentler TC map, short-shifting, earlier but smoother throttle.
- **Front graining**: reduce front sliding. Less entry understeer (balance), more front pressure or camber to bring temperature up faster on a cold day, a driver warm-up phase (no hard sliding for the first laps).
- **Blistering**: reduce bulk temperature. Less camber, lower pressure if within limits (careful: more carcass heat), reduce sliding, cooler brake ducts if rim heat feeds the tyre.
- **Wear**: reduce sliding energy. Balance, toe (excess toe scrubs), smooth inputs.

**Tyre management for drivers** is an engineering-agreed plan: lift-and-coast before key braking zones (cooler fronts, saves fuel), protect the rears on traction-limited exits, avoid sliding in long high-energy corners, and change the brake bias and TC through the stint as balance drifts.

## L3 · Advanced

**Mechanisms in more depth.**
- **Graining** occurs when the tread surface is stiff (below its glass-transition-related window) but asked to slide. The surface fails in tension and the rubber rolls up. It is promoted by cold tread, smooth/green tracks (less micro-texture penetration, more sliding), and high **sliding velocity**. Front graining from understeer is the classic case. Grains can appear on the rear from wheelspin on cold tyres.
- **Blistering** is driven by heat generated inside the tread by hysteresis (cyclic deformation) faster than it can be conducted away. Thick tread on new tyres, high pressure (centre blistering) and excessive camber (inner-shoulder blistering) are typical. Once a blister forms, local contact pressure changes and the damage propagates.
- **Thermal degradation** has a **recoverable** part (surface or bulk above window: cool it and grip returns) and an **irreversible** part (chemical/structural changes after repeated heat cycles: the rubber is "cooked"). A tyre that was overheated in a qualifying push is not as good on its second run.
- **Wear** often makes the tyre slightly *faster* for a while (less tread squirm, stiffer, better response, cooler) until compound loss or rubber thickness hits a limit.

**Quantifying deg.** Fit fuel-corrected lap time $t(n) = t_0 + d\cdot n + c\cdot n^2$ per stint, compound and track temperature. The linear term $d$ is the strategist's deg rate. The quadratic term catches cliffs. Typical orders: GT3 race tyres a few hundredths to ~0.15 s/lap; aggressive formula compounds (F2 option) can be 0.1–0.3 s/lap with a cliff. Always separate **track evolution** (rubbering-in typically makes the track faster over a session) from deg by comparing with other cars on similar tyre age.

**Setup for the stint, not the lap.** The fastest qualifying setup often overloads the limiting tyre. Race setups move balance slightly towards protecting the tyre that degrades first (e.g. more understeer at stint start on a rear-limited car), accepting a slower lap 1 for a faster average.

## L4 · Expert

**Model-based degradation management.**
- **Energy metrics.** Tyre energy per lap $E_i = \int |F_i \cdot v_{slip,i}|\,dt$ (from a vehicle model or estimated from forces and slip) correlates better with wear and thermal deg than temperatures alone. Comparing $E_i$ per wheel per corner shows where the driver and setup spend the tyre, and where management (lift, smoother release, different line) is cheapest in lap time.
- **Lap-time sensitivity vs tyre-life sensitivity.** For each corner, estimate Δlap-time and Δenergy for a management action (e.g. 10 m lift-and-coast before T1). Management is efficient where Δenergy/Δtime is large: usually long, high-speed, sliding-dominated corners for fronts and low-gear exits for rears.
- **Thermal runaway.** Above the window, grip falls, so the driver must slide more for the same speed, generating more heat: positive feedback. Engineering response: change the target to *stay below* the knee (lower driver aggression in specific corners) rather than recover afterwards.
- **Interaction with pressures.** As bulk temperature rises over a stint, hot pressures rise, contact patch shrinks, and load sensitivity worsens. Thermal deg can therefore show up as a balance change through pressure even when μ at the surface is stable. Start-pressure choice is a degradation tool.
- **Strategic edge cases:** short-fill stints on used tyres, safety-car restarts with cold, grained tyres, and a cliff that arrives earlier on hot afternoons. A good race engineer briefs the driver on the expected deg curve and the in-car tools (bias, TC, diff, ARB if available) before the stint, not during it.

## Key formulas

**Fuel-corrected lap time**

$$t_{corr}(n) = t(n) + k_f\,m_{fuel,burnt}(n)$$

- k_f: fuel sensitivity (s per kg per lap), ~0.02–0.04
- m_{fuel,burnt}: fuel used since stint start (kg)

**Degradation fit**

$$t_{corr}(n) = t_0 + d\,n + c\,n^2$$

- d: linear deg rate (s/lap)
- c: curvature (cliff indicator)

**Tyre energy per lap**

$$E_i = \int_{lap} \left|\mathbf{F}_i \cdot \mathbf{v}_{slip,i}\right|\,dt$$


## Trackside takeaways

- Correct lap times for fuel (~0.02–0.04 s/kg/lap) before calling degradation.
- Graining = too cold for the sliding and often cleans up; blistering = bulk too hot and doesn’t recover.
- Use grip-factor run charts (overall/cornering/braking/traction/aero) to see which axle and phase is degrading.
- Balance drift over a stint (understeer angle per lap) shows which axle is going first.
- Thermal runaway is positive feedback: manage to stay below the knee rather than recovering afterwards.

## By car category

### GT3

Rear-traction degradation on RWD cars is the most common stint limiter. Expect understeer angle to trend towards oversteer as the stint goes on. TC maps and brake bias are the in-stint tools. Double-stinting tyres in endurance races makes deg modelling a strategic weapon.

### FIA F2

Pit-stop-mandatory races with two compounds. Option-tyre degradation can be large with a pronounced cliff, and managing the rear tyres in the first stint is often decisive. Graining on cooler days is a recurring theme.

### Hypercar (LMH/LMDh)

Multi-stint tyre use and compound choice across day/night temperature swings make thermal degradation the central variable. Hybrid deployment and the front-axle drive on LMH cars alter which axle degrades.

### TCR

The outside front tyre is the limiter: it brakes, steers and drives. Front graining on cold days and front shoulder wear are typical, and drivers manage with lift-and-coast and reduced exit wheelspin.

### IndyCar

Alternate (softer) road-course tyres degrade faster with a strong falloff, so strategy hinges on how many laps to run on each. On ovals, right-side tyre wear and temperature drive the stint.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.1 Estimating Grip Levels (Grip-factor channels and run charts)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §7.5 The Understeer Angle (Balance trend over a stint)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.5 Working Temperature Range of the Tires
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior
