# Camber and camber thrust

> Negative static camber is run so the loaded outside tyre has an even contact pressure at the limit, not mainly for camber thrust. The cost is braking/traction patch, inner-shoulder heat and tyre-supplier limits.

Area: Tyres · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/tyres-camber-camber-thrust

## L1 · Foundation

**Camber** $\gamma$ is the inclination of the wheel plane from vertical, seen from the front. Top of the wheel leaning towards the chassis is **negative** camber.

A cambered rolling tyre produces a lateral force even at zero slip angle, called **camber thrust**, because the leaning contact patch is curved and the tread is forced along an arc. Motorcycle tyres live on it. On a wide, flat racing car slick it is small: camber stiffness is only a fraction of cornering stiffness per degree, so it is not why we run camber.

The main reason is **contact patch shape under load**. In a corner:
1. the body rolls (1–2° on a GT, well under 1° on a stiff formula car), tilting the outside wheel towards positive camber;
2. the tyre itself deflects laterally, so the tread rolls under and loads the outside shoulder;
3. suspension geometry recovers part of that (camber gain in bump).

Static negative camber pre-compensates so that, at peak lateral load, the outside tyre presses the whole tread width evenly onto the road. Typical static values:

| Car | Front static | Rear static |
|---|---|---|
| GT3 | ~ −3.0 to −4.0° | ~ −2.0 to −3.0° |
| GT4 / Cup | ~ −2.5 to −4.0° | ~ −2.0 to −3.0° |
| Formula (F4–F2) | ~ −2.5 to −4.0° | ~ −1.0 to −2.5° |

The price: in a straight line the patch is narrower and biased to the inner shoulder. That costs braking and traction, raises inner-shoulder temperature and can cause **inner-shoulder blistering**. Tyre suppliers often publish a **maximum camber** (and sometimes a minimum pressure) for exactly this reason. Respect it, especially on high-speed tracks.

## L2 · Practitioner

**Setting camber trackside.**
- Start from supplier and manufacturer guidance (the car's base setup sheet). On a new track type adjust in 0.25–0.5° steps.
- **Probe temperatures** (inner/middle/outer) are the classic camber read. A rough guide on most slicks: the inner shoulder 5–10 °C hotter than outer at the pit-lane probe means the camber is in a sensible range. Equal or outer-hotter means more negative camber could be used; inner 15+ °C hotter means too much. Segers' corner-by-corner IR analysis showed that the same wheel can want more camber as the outside wheel and less as the inside wheel. Static camber is always a compromise across corners.
- **Track bias** matters: on a clockwise circuit with mostly right-handers, the left tyres are outside tyres most of the time. Asymmetric camber (left more negative than right) is common and legal in most series.

**Dynamic camber estimate.** Outside-wheel camber to the road is roughly

$$\gamma_{dyn} \approx \gamma_{static} + \phi\,(1 - k_{cg}) + \gamma_{tyre}$$

with roll angle $\phi$, camber recovery fraction $k_{cg}$ (how much of the body roll the geometry gives back) and tyre-deflection camber $\gamma_{tyre}$. Example GT3 front: −3.5° static, 1.5° roll, 50% recovery gives −2.75°. The tyre's own lateral deflection adds roughly another +0.5–1°, leaving around −2° to the road, which is close to the optimum for many GT slicks under peak load.

**Interactions.**
- More negative front camber usually sharpens turn-in and mid-corner front grip, but lengthens braking distances and increases inside-front lock tendency.
- Rear camber trades lateral stability against traction. Many RWD cars run less rear camber at tracks with heavy traction demand.
- Stiffer roll (bars/springs) reduces roll, so less camber compensation is needed. Changing roll stiffness without revisiting camber leaves performance on the table.
- Camber plus toe causes scrub drag and heat. High camber at high-speed tracks (Monza, Le Mans) raises shoulder temperatures on the straights.

## L3 · Advanced

**Camber thrust in numbers.** For a radial racing slick, camber stiffness $C_\gamma$ is roughly an order of magnitude smaller than $C_\alpha$ per degree. Tread width and belt stiffness resist the curved-path mechanism, so a degree of camber is worth only a fraction of a degree of slip angle in lateral force. The useful camber effect on the outside tyre is that **peak μ** depends on inclination. Tyre data typically shows peak $F_y$ maximised at some negative inclination (often −1° to −3° to the road for car slicks), falling either side. Camber therefore shifts and reshapes the curve, not only adding an offset.

**Inside wheel.** Body roll takes the inside wheel towards more negative camber relative to the road: $\gamma_{in} \approx \gamma_{static} - \phi\,(1 - k_{cg})$. Camber gain in droop gives some of that back, but less than all of it (−3.5° static, 1.5° roll, 50% recovery gives about −4.25°). With large static camber, the inside tyre can therefore run on its inner shoulder at very negative effective camber, which overheats that shoulder (Segers' Table 8.2 example: inner shoulder heating "too much" whenever the wheel is on the inside). Segers' remedy is more dynamic camber change combined with less static camber, which helps the inside wheel without giving up the outside one. If the inside tyre is lightly loaded its force contribution is small. On slow, high-roll corners, though, it matters.

**Geometry trade-off.** More camber gain in bump (short swing-arm) keeps the outside tyre upright in roll and allows less static camber, so it is better in a straight line. But it also changes camber in heave and pitch, so aero-loaded cars see camber change with downforce. Formula cars with very stiff heave springs need less gain; softer-sprung GT cars need more. Roll-centre height is coupled to the same link geometry (see the suspension-geometry domain).

**Data method.** With three IR sensors per tyre, build the **spread channel** $\Delta T = T_{in} - T_{out}$ and gate it by lateral G sign, so you look at the wheel as the outside and as the inside tyre separately. Lap-average spread per wheel is a good camber statistic (Segers §8.8 reports a lap-average spread of ~7 °C on the left front as acceptable and ~15 °C on the right front as too much camber). Correlate with **lap time and balance**, not only with temperature uniformity: a slightly uneven spread is often the fastest option.

## L4 · Expert

**Why "even temperatures" is not the objective.** Temperature distribution reflects where energy is dissipated, which depends on local contact pressure *and* local slip velocity. Under combined slip the outer shoulder of the outside tyre may slide more. The fastest camber can therefore show a non-uniform spread. Treat the probe spread as a constraint (avoid blistering and overheated shoulders) and lap time or balance as the objective.

**Structural effects.** Camber changes belt tension distribution, so it changes the **effective cornering stiffness** and the **conicity-like** lateral forces in a straight line, and therefore changes straight-line stability and steering pull with asymmetric settings. High front camber combined with toe-out produces opposing camber thrusts and slip forces that cancel in force but add rolling resistance and heat.

**Simulation caveat.** Most Magic Formula fits model inclination effects on μ and stiffness fairly well around the test inclinations but extrapolate poorly beyond ±4–5°. Kinematic camber in sims must include compliance (camber compliance under $F_y$ in GT uprights, hubs and bushes is typically a few hundredths of a degree per kN, i.e. a few tenths of a degree at the limit), or predicted optimum static camber will be too small.

**Regulatory edge cases.** Supplier camber limits may be checked by scrutineers (static at a defined ride height). Running compliance-generated dynamic camber beyond the static limit is how some teams recover lap time, which is exactly what the limits are trying to prevent for durability reasons. It is a structural-safety question, not a grip one: excessive inner-shoulder loading at high speed has caused tyre failures in several series.

## Key formulas

**Camber thrust (linear)**

$$F_{y\gamma} \approx C_\gamma\,\gamma$$

- C_\gamma: camber stiffness (N/deg), small vs C_α for car slicks
- \gamma: inclination to road (deg)

**Outside-wheel dynamic camber (approx.)**

$$\gamma_{dyn} \approx \gamma_{static} + \phi\,(1 - k_{cg}) + \gamma_{tyre}$$

- \phi: body roll angle (deg)
- k_cg: roll camber recovery fraction (0–1)
- \gamma_{tyre}: tyre-deflection camber (deg)

**Temperature spread channel**

$$\Delta T_{spread} = T_{in} - T_{out}$$


## Trackside takeaways

- On car slicks, negative camber is about patch pressure on the loaded outside tyre, not camber thrust.
- Static camber costs braking/traction and heats the inner shoulder. Respect supplier camber limits.
- Probe spread inner hotter by ~5–10 °C is a typical healthy range; 15+ °C points to too much camber.
- Less roll (stiffer bars/springs) means less camber compensation needed. Revisit camber after roll-stiffness changes.
- Gate IR spread by corner direction: the same wheel may want more camber outside and less inside.

## By car category

### GT3

Body roll of ~1–2° and soft-ish springs mean large static camber (front often −3.5° or more). Supplier camber limits are relevant at high-speed tracks. Asymmetric left/right camber is common for clockwise/anticlockwise bias.

### One-make Cup

Cup cars often have camber ranges defined by the series, and a control tyre with known inner-shoulder sensitivity. Engineers tend to run near the allowed maximum front camber and fine-tune with pressures.

### FIA F2

Pirelli-prescribed camber limits apply. With high downforce and stiff heave control, roll is small, so dynamic camber is close to static plus compliance. Inner-shoulder overheating on long straights is a known durability concern.

### IndyCar

On ovals, camber is set asymmetrically: the right-side (outside) wheels run substantial negative camber, while the left side can even run positive. Road-course settings are closer to symmetric.

### TCR

MacPherson front struts have poor camber recovery in roll, so TCR cars need a lot of static front camber (several degrees, usually at or near the limit of the allowed adjustment). Inner-shoulder wear on the front is the price.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior (Camber thrust and inclination effects)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 17 Suspension Geometry (Camber change in roll)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.8 Camber Evaluation with Tire Temperature Sensors
